BM/AMCC PowerPC 440 GR Rev. B Board: AMCC YELLOWSTONE VCO: 1066 MHz CPU: 533 MHz PLB: 133 MHz OPB: 66 MHz PER: 66 MHz PCI: 33 MHz I2C: ready DRAM: 256 MB FLASH: 32 MB PCI: Bus Dev VenId DevId Class Int 00 0c 1106 3038 0c03 00 00 0c 1106 3038 0c03 00 00 0c 1106 3104 0c03 00 00 0c 1106 3249 0104 0e In: serial Out: serial Err: serial Net: ppc_440x_eth0, ppc_440x_eth1 Hit any key to stop autoboot: 0 => tftp 200000 z2 Waiting for PHY auto negotiation to complete.. done Using ppc_440x_eth0 device TFTP from server 192.168.0.100; our IP address is 192.168.0.101 Filename 'z2'. Load address: 0x200000 Loading: T ################################################################# ################################################################# ################################################################# ######################################################## done Bytes transferred = 1283382 (139536 hex) => bootm ## Booting image at 00200000 ... Image Name: Linux-2.6.19 Created: 2009-03-22 9:52:51 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1283318 Bytes = 1.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.6.19 (r...@debian) (gcc version 4.2.2) #10 Sun Mar 22 02:51:52 9AMCC PowerPC 440GR Yellowstone Platform Zone PFN ranges: DMA 0 -> 65536 Normal 65536 -> 65536 early_node_map[1] active PFN ranges 0: 0 -> 65536 Built 1 zonelists. Total pages: 65024 Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.100:/opt/eldk4.2/ppc_4xlMisrouted IRQ fixup and polling support enabled This may significantly impact system performance PID hash table entries: 1024 (order: 10, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 257024k available (1940k kernel code, 668k data, 148k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 PCI: Probing PCI hardware SCSI subsystem initialized NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 8192 bind 4096) TCP reno registered io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at MMIO 0x0 (irq = 0) is a 16550A serial8250: ttyS1 at MMIO 0x0 (irq = 1) is a 16550A RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize PPC 4xx OCP EMAC driver, version 3.54 mal0: initialized, 4 TX channels, 2 RX channels zmii0: bridge in RMII mode eth0: emac0, MAC 00:10:ec:00:89:89 eth0: found Generic MII PHY (0x01) eth1: emac1, MAC 00:10:ec:80:89:89 eth1: found Generic MII PHY (0x03) in init_module Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx sata_via 0000:00:0c.3: routed to hard irq line 9 ata1: SATA max UDMA/133 cmd 0xFFB0 ctl 0xFFBA bmdma 0xFF60 irq 25 ata2: SATA max UDMA/133 cmd 0xFFA0 ctl 0xFFAA bmdma 0xFF68 irq 25 scsi0 : sata_via ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: qc timeout (cmd 0xec) ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: qc timeout (cmd 0xec) ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: qc timeout (cmd 0xec) in err_mask becoz of exec ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) scsi1 : sata_via ata2: SATA link down (SStatus 0 SControl 310) ATA: abnormal status 0x7F on port 0xFFA7 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 eth0: link is up, 100 FDX, pause enabled IP-Config: Complete: device=eth0, addr=192.168.0.101, mask=255.255.0.0, gw=192.168.0.100, host=ppc, domain=, nis-domain=(none), bootserver=192.168.0.100, rootserver=192.168.0.100, rootpath= Looking up port of RPC 100003/2 on 192.168.0.100 Looking up port of RPC 100005/1 on 192.168.0.100 VFS: Mounted root (nfs filesystem). Freeing unused kernel memory: 148k init INIT: version 2.86 booting Welcome to DENX Embedded Linux Environment Press 'I' to enter interactive startup. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Setting clock : Thu Jan 1 01:01:51 CET 1970 [ OK ] Building the cache [ OK ] Setting hostname ppc: [ OK ] Mounting local filesystems: [ OK ] Enabling /etc/fstab swaps: [ OK ] INIT: Entering runlevel: 3 Entering non-interactive startup FATAL: Module ipv6 not found. Bringing up loopback interface: [ OK ] FATAL: Module ipv6 not found. Starting system logger: [ OK ] Starting kernel logger: [ OK ] Starting rpcbind: [ OK ] Mounting NFS filesystems: [ OK ] Mounting other filesystems: [ OK ] Starting xinetd: [ OK ]
DENX ELDK version 4.2 build 2008-04-01 Linux 2.6.19 on a ppc adding irqpoll, noacpi option to the bootargs is not working. any suggestion??? -- View this message in context: http://www.nabble.com/sata-device-failed-to-IDENTIFY...-tp22655709p22655709.html Sent from the linuxppc-dev mailing list archive at Nabble.com. _______________________________________________ Linuxppc-dev mailing list Linuxppc-dev@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-dev