The same happens with my v440 most of the time, but not always.
Am 08.03.2011 11:10, schrieb Mattieu Baptiste: > Hi all, > > I know this setup might not be fully supported but I wanted to report this. > > On my Sun Fire V240 I have two softraid(4) volumes: > - sd4 (UUID a45b5629cc97897e), RAID1 for : /tmp, /var, /usr, /home > - sd5 (UUID 5cd55a71b5790766), RAID0 for data. > > My /etc/fstab is as follows: > 00000000438d5c40.b none swap sw 0 0 > /dev/sd0a / ffs rw,softdep 1 1 > 00000000438d5c40.a /altroot ffs xx 0 0 > a45b5629cc97897e.h /home ffs rw,nodev,nosuid,softdep 1 2 > a45b5629cc97897e.d /tmp ffs rw,nodev,nosuid,softdep 1 2 > a45b5629cc97897e.g /usr ffs rw,nodev,softdep 1 2 > a45b5629cc97897e.e /var ffs rw,nodev,nosuid,softdep 1 2 > 5cd55a71b5790766.k /var/www/ftp ffs rw,nodev,nosuid,softdep 1 2 > > When I try to reboot the machine, it stalls at: > $ sudo reboot > /etc/rc.shutdown in progress... > stopping local daemons: mysqld. > /etc/rc.shutdown complete. > syncing disks... done > sd5 detached > scsibus5 detached > sd4 detached > scsibus4 detached > > The only way to reboot the machine is via ALOM. > > Here is a dmesg: > > Rebooting with command: boot > Boot device: disk0 File and args: > OpenBSD IEEE 1275 Bootblock 1.3 > ..>> OpenBSD BOOT 1.4 > Trying bsd... > Booting /pci@1c,600000/scsi@2/disk@0,0:a/bsd > 6557872@0x1000000+3920@0x16410b0+179568@0x1800000+4014736@0x182bd70 > symbols @ 0xfecd2300 90+403728+254301 start=0x1000000 > [ using 658896 bytes of bsd ELF symbol table ] > console is /pci@1e,600000/isa@7/serial@0,3f8 > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2011 OpenBSD. All rights reserved. http://www.OpenBSD.org > > OpenBSD 4.9 (GENERIC.MP) #2: Wed Mar 2 13:13:28 CET 2011 > r...@test.brimbelle.org:/usr/src/sys/arch/sparc64/compile/GENERIC.MP > real mem = 2147483648 (2048MB) > avail mem = 2101043200 (2003MB) > mainbus0 at root: Sun Fire V240 > cpu0 at mainbus0: SUNW,UltraSPARC-IIIi (rev 2.4) @ 1280 MHz > cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K > external (64 b/l) > cpu1 at mainbus0: SUNW,UltraSPARC-IIIi (rev 2.4) @ 1280 MHz > cpu1: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K > external (64 b/l) > "memory-controller" at mainbus0 not configured > "memory-controller" at mainbus0 not configured > schizo0 at mainbus0: "Tomatillo", version 4, ign 7c0, bus B 0 to 0 > schizo0: dvma map c0000000-dfffffff > pci0 at schizo0 > bge0 at pci0 dev 2 function 0 "Broadcom BCM5704C" rev 0x00, BCM5704 A3 > (0x2003): ivec 0x7c8, address 00:03:ba:bd:ee:a1 > brgphy0 at bge0 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0 > bge1 at pci0 dev 2 function 1 "Broadcom BCM5704C" rev 0x00, BCM5704 A3 > (0x2003): ivec 0x7c9, address 00:03:ba:bd:ee:a2 > brgphy1 at bge1 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0 > schizo1 at mainbus0: "Tomatillo", version 4, ign 780, bus A 0 to 0 > schizo1: dvma map c0000000-dfffffff > pci1 at schizo1 > ebus0 at pci1 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00 > "flashprom" at ebus0 addr 0-fffff, 290-290 not configured > rtc0 at ebus0 addr 70-71: m5819p > pcfiic0 at ebus0 addr 320-321 ivec 0x2e > iic0 at pcfiic0 > "SUNW,i2c-imax" at iic0 addr 0xb not configured > "SUNW,i2c-imax" at iic0 addr 0xc not configured > spdmem0 at iic0 addr 0x5b: 512MB DDR SDRAM registered ECC PC2300CL2.5 > spdmem1 at iic0 addr 0x5c: 512MB DDR SDRAM registered ECC PC2300CL2.5 > spdmem2 at iic0 addr 0x63: 512MB DDR SDRAM registered ECC PC2300CL2.5 > spdmem3 at iic0 addr 0x64: 512MB DDR SDRAM registered ECC PC2300CL2.5 > "ds1307" at iic0 addr 0x68 not configured > "pca9555" at iic0 addr 0x22 not configured > "pca9555" at iic0 addr 0x23 not configured > "pca9555" at iic0 addr 0x25 not configured > "pca9555" at iic0 addr 0x44 not configured > "pca9556" at iic0 addr 0x38 not configured > power0 at ebus0 addr 800-82f ivec 0x20 > com0 at ebus0 addr 3f8-3ff ivec 0x2c: ns16550a, 16 byte fifo > com0: console > com1 at ebus0 addr 2e8-2ef ivec 0x2c: ns16550a, 16 byte fifo > "rmc-comm" at ebus0 addr 3e8-3ef ivec 0x2c not configured > alipm0 at pci1 dev 6 function 0 "Acer Labs M7101 Power" rev 0x00: 223KHz clock > iic1 at alipm0 > ohci0 at pci1 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec > 0x7a7, version 1.0, legacy support > pciide0 at pci1 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4: > DMA, channel 0 configured to native-PCI, channel 1 configured to > native-PCI > pciide0: using ivec 0x798 for native-PCI interrupt > atapiscsi0 at pciide0 channel 0 drive 0 > scsibus0 at atapiscsi0: 2 targets > cd0 at scsibus0 targ 0 lun 0: <TEAC, DV-28E-C, 1.4B> ATAPI 5/cdrom removable > cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > pciide0: channel 1 disabled (no drives) > usb0 at ohci0: USB revision 1.0 > uhub0 at usb0 "Acer Labs OHCI root hub" rev 1.00/1.00 addr 1 > schizo2 at mainbus0: "Tomatillo", version 4, ign 700, bus A 0 to 0 > schizo2: dvma map c0000000-dfffffff > pci2 at schizo2 > siop0 at pci2 dev 2 function 0 "Symbios Logic 53c1010-66" rev 0x01: > ivec 0x729, using 8K of on-board RAM > scsibus1 at siop0: 16 targets, initiator 7 > sd0 at scsibus1 targ 0 lun 0: <SEAGATE, ST336607LSUN36G, 0207> SCSI3 > 0/direct fixed > sd0: 34732MB, 512 bytes/sec, 71132959 sec total > sd1 at scsibus1 targ 1 lun 0: <SEAGATE, ST336607LSUN36G, 0207> SCSI3 > 0/direct fixed > sd1: 34732MB, 512 bytes/sec, 71132959 sec total > sd2 at scsibus1 targ 2 lun 0: <COMPAQ, BF1468A4B3, HPB5> SCSI3 0/direct fixed > sd2: 140014MB, 512 bytes/sec, 286749488 sec total > sd3 at scsibus1 targ 3 lun 0: <COMPAQ, BF14687B56, HPB9> SCSI3 0/direct fixed > sd3: 140014MB, 512 bytes/sec, 286749488 sec total > siop1 at pci2 dev 2 function 1 "Symbios Logic 53c1010-66" rev 0x01: > ivec 0x728, using 8K of on-board RAM > scsibus2 at siop1: 16 targets, initiator 7 > schizo3 at mainbus0: "Tomatillo", version 4, ign 740, bus B 0 to 0 > schizo3: dvma map c0000000-dfffffff > pci3 at schizo3 > bge2 at pci3 dev 2 function 0 "Broadcom BCM5704C" rev 0x00, BCM5704 A3 > (0x2003): ivec 0x75c, address 00:03:ba:bd:ee:a3 > brgphy2 at bge2 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0 > bge3 at pci3 dev 2 function 1 "Broadcom BCM5704C" rev 0x00, BCM5704 A3 > (0x2003): ivec 0x75d, address 00:03:ba:bd:ee:a4 > brgphy3 at bge3 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0 > ifb0 at pci3 dev 1 function 0 "3D Labs Wildcat 5110" rev 0x01 > ifb0: XVR-500 (SUNW,375-3069), 1152x900 > wsdisplay0 at ifb0 mux 1 > wsdisplay0: screen 0 added (std, sun emulation) > siop0: target 0 now using tagged DT 16 bit 80.0 MHz 62 REQ/ACK offset xfers > vscsi0 at root > scsibus3 at vscsi0: 256 targets > softraid0 at root > siop0: target 1 now using tagged DT 16 bit 80.0 MHz 62 REQ/ACK offset xfers > siop0: target 2 now using tagged DT 16 bit 80.0 MHz 31 REQ/ACK offset xfers > siop0: target 3 now using tagged DT 16 bit 80.0 MHz 31 REQ/ACK offset xfers > scsibus4 at softraid0: 1 targets > sd4 at scsibus4 targ 0 lun 0: <OPENBSD, SR RAID 1, 004> SCSI2 0/direct fixed > sd4: 32433MB, 512 bytes/sec, 66423360 sec total > scsibus5 at softraid0: 1 targets > sd5 at scsibus5 targ 0 lun 0: <OPENBSD, SR RAID 0, 004> SCSI2 0/direct fixed > sd5: 280023MB, 512 bytes/sec, 573487616 sec total > bootpath: /pci@1c,600000/scsi@2,0/disk@0,0 > root on sd0a swap on sd0b dump on sd0b > swapctl: adding 00000000438d5c40.b as swap device at priority 0 > Automatic boot in progress: starting file system checks. > /dev/rsd0a: file system is clean; not checking > /dev/sd5k (5cd55a71b5790766.k): file system is clean; not checking > /dev/sd4h (a45b5629cc97897e.h): file system is clean; not checking > /dev/sd4d (a45b5629cc97897e.d): file system is clean; not checking > /dev/sd4g (a45b5629cc97897e.g): file system is clean; not checking > /dev/sd4e (a45b5629cc97897e.e): file system is clean; not checking > setting tty flags > pf enabled > starting network > starting system logger > starting named > starting initial daemons: ntpd. > savecore: no core dump > checking quotas: done. > building ps databases: kvm dev. > clearing /tmp > starting pre-securelevel daemons:. > setting kernel security level: kern.securelevel: 0 -> 1 > creating runtime link editor directory cache. > preserving editor files. > starting network daemons: sshd sendmail httpd ftpd inetd. > starting local daemons: mysqld. > standard daemons: cron. > Tue Mar 8 10:58:39 CET 2011 > > OpenBSD/sparc64 (test.brimbelle.org) (console) > > login:
