On Fri, 2016-06-03 at 13:49 -0700, Ali Nematollahi wrote: > That was a great point Dan. It went one step forward: > > .... > [ 2299.953517] [sched_delayed] sched: RT throttling activated > [ 2300.344384] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11) > NetworkManager[2845]: <info> (wlan0): using nl80211 for WiFi device > control > [ 2300.379934] wlcore: loaded > [ 2300.382856] wlcore: driver version: > NetworkManager[2845]: <info> (wlan0): driver supports Access Point > (AP) > mode > NetworkManager[2845]: <info> (wlan0): new 802.11 WiFi device > (carrier: > UNKNOWN, driver: 'wl18xx_driver', ifindex: 5) > NetworkManager[2845]: <info> rfkill0: found WiFi radio killswitch > (at > /sys/devices/ocp.2[ 2300.415536] wlcore: compilation time: Thu Jun 26 > 11:35:53 2014 > /47810000.mmc/mmc_host/mmc2/mmc2:0001/mmc2:0001:2/wl18xx.2.auto/ieee8 > 0211/phy0/rfkill0) > (driver wl18xx_driver) > NetworkManager[2845]: <info> devices added (path: > /sys/devices/ocp.2/47810000.mmc/mmc_host/mmc2/mmc2:0001/mmc2:0001:2/w > l18xx.2.auto/net/wlan0, > iface: wlan0) > NetworkManager[2845]: <info> device added (path: > /sys/devices/ocp.2/47810000.mmc/mmc_host/mmc2/mmc2:0001/mmc2:0001:2/w > l18xx.2.auto/net/wlan0, > iface: wlan0): no ifupdown configuration found. > NetworkManager[2845]: <info> wpa_supplicant running > NetworkManager[2845]: <info> (wlan0): device state change: unmanaged > -> > unavailable (reason 'managed') [10 20 2] > [ 2300.952925] wlcore: PHY firmware version: Rev 8.2.0.0.195 > [ 2301.042483] wlcore: firmware booted (Rev 8.8.0.0.13) > NetworkManager[2845]: <info> (wlan0) supports 1 scan SSIDs > NetworkManager[2845]: <info> (wlan0): supplicant interface state: > starting > -> ready > NetworkManager[2845]: <info> (wlan0): device state change: > unavailable -> > disconnected (reason 'supplicant-available') [20 30 42] > > root@beaglebone:/etc/NetworkManager/system-connections# ifconfig > eth0 Link encap:Ethernet HWaddr ec:24:b8:cf:e0:be > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) > Interrupt:56 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > UP LOOPBACK RUNNING MTU:65536 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) > > wlan0 Link encap:Ethernet HWaddr 5c:31:3e:ce:be:5b > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) > > > > I see the supplicant-available message and wlan0 comes up as it did > before > but still there's no IP address nor SSID is broadcast. Should I do an > ipconfig to assign an IP to the interface manually? What about SSID > broadcast?
No, you shouldn't need to do that. It looks like NM isn't starting the AP connection at all. Could you run: nmcli -f all dev show wlan0 | grep AVAIL and let's see what connections/profiles NM things the wifi interface can activate. Next, try: nmcli con up Hotspot and lets see what NM says to that. Dan > Thanks! > > On Fri, Jun 3, 2016 at 8:25 AM, Dan Williams <d...@redhat.com> wrote: > > > > > On Thu, 2016-06-02 at 15:03 -0700, Ali Nematollahi wrote: > > > > > > Hi guys > > > > > > I'm trying to use NM to start a WiFi AP mode. I've had some > > > success > > > but a > > > big portion of the process is very unclear to me and I'm hoping > > > to > > > get some > > > help. > > > > > > So I have this NM configuration: > > > > > > # cat Hotspot > > > [connection] > > > id=Hotspot > > > uuid=3e13073d-6d7a-440d-ab2b-4f42c9fdacaf > > > type=802-11-wireless > > > autoconnect=true > > > > > > [802-11-wireless] > > > ssid=AliAP > > > mode=ap > > > security=802-11-wireless-security > > > > > > [802-11-wireless-security] > > > key-mgmt=wpa-psk > > > psk=alisecurepassword984364@234@ > > > > > > [ipv4] > > > method=shared > > > > > > [ipv6] > > > method=auto > > Looks good so far. > > > > > > > > > > > With this, the NM starts up and does what it needs to do (I > > > think): > > > (NetworkManager:2989): NetworkManager-WARNING **: <warn> glib- > > > version: > > > cannot handle SIGUSR1 and SIGUSR2 signals. Consider upgrading > > > glib to > > > 2.36.0 or newer > > > NetworkManager[2989]: <info> NetworkManager (version 1.0.10) is > > > starting... > > > NetworkManager[2989]: <info> Read config: > > > /etc/NetworkManager/NetworkManager.conf > > > NetworkManager[2989]: <info> init! > > > NetworkManager[2989]: <info> update_system_hostname > > <snip> > > > > > > > > NetworkManager[2989]: <info> (wlan0): new 802.11 WiFi device > > > (carrier: > > > UNKNOWN, driver: 'wl18xx_driver', ifindex: 5) > > > NetworkManager[2989]: <info> (wlan0): device state change: > > > unmanaged > > > -> > > > unavailable (reason 'managed') [10 20 2] > > > [ 1424.134834] wlcore: PHY firmware version: Rev 8.2.0.0.195 > > > [ 1424.222506] wlcore: firmware booted (Rev 8.8.0.0.13) > > > [ 1424.244537] wlcore: down > > > [ 1424.664565] wlcore: PHY firmware version: Rev 8.2.0.0.195 > > > [ 1424.752521] wlcore: firmware booted (Rev 8.8.0.0.13) > > > NetworkManager[2989]: <info> (can0): new Generic device > > > (carrier: > > > UNKNOWN, > > > driver: 'c_can_platform', ifindex: 2) > > > NetworkManager[2989]: <info> (can1): new Generic device > > > (carrier: > > > UNKNOWN, > > > driver: 'c_can_platform', ifindex: 3) > > > NetworkManager[2989]: <info> wpa_supplicant stopped > > > NetworkManager[2989]: <info> (wlan0): supplicant interface > > > state: > > > starting > > > -> init > > Looking at the code, I don't think NM is able to talk to > > wpa_supplicant. This line (starting -> init) will only get printed > > if > > D-Bus failed to service activate the supplicant. There's two fixes > > there: > > > > 1) fix whatever problem is wrong with D-Bus service activation; > > this > > requires that D-Bus is built with the same --datadir as > > wpa_supplicant, > > and that the /usr/share/dbus-1/system- > > services/fi.w1.wpa_supplicant1.service file exists and points to > > the > > wpa_supplicant binary. > > > > 2) run the supplicant at system startup with the "-u" (enable D-Bus > > interface) option; either as a system service via your normal > > service > > framework (sysvinit, openrc, systemd, etc) or just launch it > > manually > > somehow. > > > > Once NM can talk to wpa_supplicant, it should start your AP > > connection > > and actually enable the AP on wlan0. > > > > Dan > > > > > > > > > > > # ifconfig > > > eth0 Link encap:Ethernet HWaddr ec:24:b8:cf:e0:be > > > UP BROADCAST MULTICAST MTU:1500 Metric:1 > > > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:1000 > > > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) > > > Interrupt:56 > > > > > > lo Link encap:Local Loopback > > > inet addr:127.0.0.1 Mask:255.0.0.0 > > > UP LOOPBACK RUNNING MTU:65536 Metric:1 > > > RX packets:4 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:0 > > > RX bytes:448 (448.0 B) TX bytes:448 (448.0 B) > > > > > > wlan0 Link encap:Ethernet HWaddr 5c:31:3e:ce:be:5b > > > UP BROADCAST MULTICAST MTU:1500 Metric:1 > > > RX packets:49 errors:0 dropped:21 overruns:0 frame:0 > > > TX packets:49 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:1000 > > > RX bytes:7734 (7.5 KiB) TX bytes:8838 (8.6 KiB) > > > > > > > > > So WLAN0 is up. Great! > > > > > > When I was using "iw" and stuff to set up my AP, I used to start > > > hostapd > > > and udhcpd to set up the IP address, and start broadcasting the > > > SSID. > > > When I get to this point with NM, I was under the impression that > > > NM > > > would > > > take care of all of this. But I cannot see my SSID on my phone. I > > > do > > > have a > > > functioning wpa_supplicant btw. > > > > > > Out of curiosity, I started hostapd and udhcpd. I could get > > > hostapd > > > to work > > > (but not the SSID I set in NM!!) and UDHCPD never worked. > > > > > > I was wondering what I was missing in this and how I can start > > > the > > > broadcast and activate the DHCPD automatically with NM. > > > > > > I'm running NM 1.0.10. > > > > > > > > > > > > Thanks! > > > _______________________________________________ > > > networkmanager-list mailing list > > > networkmanager-list@gnome.org > > > https://mail.gnome.org/mailman/listinfo/networkmanager-list _______________________________________________ networkmanager-list mailing list networkmanager-list@gnome.org https://mail.gnome.org/mailman/listinfo/networkmanager-list