Thanks Murphy , I will try it On Friday, August 29, 2014, Murphy McCauley <murphy.mccau...@gmail.com> wrote:
> Remove eth3 from the OVS datapath and make sure it still has the IP you > think it should. > > Please consider not dropping this list. > > -- Murphy > > On Aug 29, 2014, at 12:16 AM, Chanthan Hel <hel.chantha...@gmail.com > <javascript:_e(%7B%7D,'cvml','hel.chantha...@gmail.com');>> wrote: > > Hi Murphy > Eth3 that connects to controller has ip 172.16.0.1 in the same netmask > with controller. > That port is USB port, but I use USB to ethernet adapter. And about what u > said, in bound control! I'm not so clear . How can we assign it to in bound > or out bound controll. > Best regards > > > On Friday, August 29, 2014, Murphy McCauley <murphy.mccau...@gmail.com > <javascript:_e(%7B%7D,'cvml','murphy.mccau...@gmail.com');>> wrote: > >> It's strange that just installing OVS would cause a problem unless you >> assigned the port that leads to the controller to the switch without >> setting up in-band control. >> >> Is eth1 connected to the controller? Does it have a 172.16.x.x address >> or whatever? >> >> -- Murphy >> >> On Aug 28, 2014, at 1:32 AM, Chanthan Hel <hel.chantha...@gmail.com> >> wrote: >> >> Dear all, >> Please help me for this point. >> I install open vswitch in one PC and pox controller in another PC and i >> use Ethernet cable to connect. IP of controller and ovs are in same subnet >> mask. >> >> i install open vswitch as mentioned in installation guide >> >> http://git.openvswitch.org/cgi-bin/gitweb.cgi?p=openvswitch;a=blob_plain;f=INSTALL;hb=HEAD >> >> i added port to switch as shown >> root@pc2-To-be-filled-by-O-E-M:~/openvswitch-1.9.0# ovs-ofctl show s2 >> OFPT_FEATURES_REPLY (xid=0x1): dpid:0000000000002201 >> n_tables:255, n_buffers:256 >> capabilities: FLOW_STATS TABLE_STATS PORT_STATS QUEUE_STATS ARP_MATCH_IP >> actions: OUTPUT SET_VLAN_VID SET_VLAN_PCP STRIP_VLAN SET_DL_SRC >> SET_DL_DST SET_NW_SRC SET_NW_DST SET_NW_TOS SET_TP_SRC SET_TP_DST ENQUEUE >> 1(eth2): addr:00:00:00:00:22:04 >> config: 0 >> state: LINK_DOWN >> current: 100MB-FD AUTO_NEG >> advertised: 10MB-HD 10MB-FD 100MB-HD 100MB-FD COPPER AUTO_NEG >> AUTO_PAUSE AUTO_PAUSE_ASYM >> supported: 10MB-HD 10MB-FD 100MB-HD 100MB-FD COPPER AUTO_NEG >> speed: 100 Mbps now, 100 Mbps max >> 2(eth3): addr:00:00:00:00:22:05 >> config: 0 >> state: 0 >> current: 100MB-FD AUTO_NEG >> advertised: 10MB-HD 10MB-FD 100MB-HD 100MB-FD COPPER AUTO_NEG >> AUTO_PAUSE AUTO_PAUSE_ASYM >> supported: 10MB-HD 10MB-FD 100MB-HD 100MB-FD COPPER AUTO_NEG >> speed: 100 Mbps now, 100 Mbps max >> 3(eth4): addr:00:00:00:00:22:01 >> config: 0 >> state: LINK_DOWN >> current: 100MB-FD AUTO_NEG >> advertised: 10MB-HD 10MB-FD 100MB-HD 100MB-FD COPPER AUTO_NEG >> AUTO_PAUSE AUTO_PAUSE_ASYM >> supported: 10MB-HD 10MB-FD 100MB-HD 100MB-FD COPPER AUTO_NEG >> speed: 100 Mbps now, 100 Mbps max >> LOCAL(s2): addr:00:00:00:00:22:01 >> config: PORT_DOWN >> state: LINK_DOWN >> speed: 100 Mbps now, 100 Mbps max >> OFPT_GET_CONFIG_REPLY (xid=0x3): frags=normal miss_send_len=0 >> >> but when i run pox, i check the ovs status it shows >> >> root@pc2-To-be-filled-by-O-E-M:~/openvswitch-1.9.0# ovs-vsctl show >> 849f606f-023d-435c-9548-1076994ec562 >> Bridge "s2" >> Controller "tcp:172.16.0.9:6633" >> Port "s2" >> Interface "s2" >> type: internal >> Port "eth3" >> Interface "eth3" >> Port "eth2" >> Interface "eth2" >> Port "eth4" >> Interface "eth4" >> It means no connection to controller and I can't ping to controller >> either. But before installing ovs i can ping to controller. I don't know >> what happen. >> Best regards >> Chanthan >> >> >> -- >> Mr. Chanthan Hel >> Electrical engineering, Faculty of Engineering, >> Chulalongkorn University (CU) >> >> *Phone: +66 81 456 84 27* >> >> >> > > -- > Mr. Chanthan Hel > Electrical engineering, Faculty of Engineering, > Chulalongkorn University (CU) > > *Phone: +66 81 456 84 27* > > > <IMG_0924.JPG> > > > -- Mr. Chanthan Hel Electrical engineering, Faculty of Engineering, Chulalongkorn University (CU) *Phone: +66 81 456 84 27*
