Re: [XFree86] XFree86-4.6.0 for Radeon R250 M9
On Mon, 11 Jun 2007, Bharat Kumar Reddy wrote: On 6/11/07, Marc Aurele La France [EMAIL PROTECTED] wrote: On Sat, 9 Jun 2007, Bharat Kumar Reddy wrote: On 6/8/07, Marc Aurele La France [EMAIL PROTECTED] wrote: On Fri, 8 Jun 2007, Bharat Kumar Reddy wrote: I am tring to configure XFree86-4.6.0 for Radeon R250 M9 . However I am seeing V_BIOS not found error. With option NoInt10 I am able to overcome this error. However I am not able to overcome the following errors: (WW) RADEON(1): Mode pool is empty (EE) RADEON(1): No valid modes found I even tried adding the horizantal and vertical refresh rate and also Modeline parameters in monitor section and no hope getting rid of this error. Can anyone help me. Attached the XFree86.log and XF86Config file. I am running FC6 on a Pentium III processor. Please forward a log without the NoInt10 option. I have removed NoInt10 option as specified. I have attached XFree86.log and XF86Config file. Earlier I have started with the attached configuration. When I ran XFree86 -xf86config /root/XF86config.new I have seen the X display coming up for Card0 (82815 CGC) only. I didn't see any display for my card1 (Radeon R250 Moblity 9000). I couldn't figure out the reason for failure in card1 inspite of success in BIOS detection. I have even tried adding the Modeline paramteres and horizantal and vertical refresh rate in Monitor Section. My monitor connected to Card1 is Acer 77c. The adapter will not function without being initialised by its BIOS, and there's not much the driver (by itself) can do about it. So the next step is to figure out why that BIOS can't be retrieved. Towards that end, please send me the output from `scanpci -v` on this system, after a powerdown-reboot, but before any attempt to start an X server. Secondly, you appear to have an incomplete installation of XFree86 4.6.0, as /usr/X11R6/lib/modules/linux/libint10.a is missing. Although I don't think this is relevant to the problem. I have disabled the X by changing the runlevel to init 3 followed by reboot. After reboot I have issued the command scanpci -v and output is attached in scanpci.txt. Thanks. Next, let's try retrieving that BIOS ourselves. Again, before attempting to start any X server, please do, as root, ... pcitweak -r 2:4:0 0x30 You should see ... 0x8012 If so, continue with ... pcitweak -w 2:4:0 0x30 0x80120001 mmapr /dev/mem 0x8012 0x2 | gzip -9 BIOS.gz pcitweak -w 2:4:0 0x30 0x8012 ... and send me (privately, not to the list) BIOS.gz. Please be mindful of typos in the above commands. Yes you are right, int10 is missing under /usr/X11R6/lib/modules/linux. I will check it out the reason for this behaviour. OK. Thanks. Marc. +--+--+ | Marc Aurele La France | work: 1-780-492-9310 | | Academic Information and| fax:1-780-492-1729 | |Communications Technologies | email: [EMAIL PROTECTED] | | 352 General Services Building +--+ | University of Alberta | | | Edmonton, Alberta |Standard disclaimers apply| | T6G 2H1 | | | CANADA | | +--+--+ XFree86 developer and VP. ATI driver and X server internals. ___ XFree86 mailing list XFree86@XFree86.Org http://XFree86.Org/mailman/listinfo/xfree86
Re: [XFree86] XFree86-4.6.0 for Radeon R250 M9
On Mon, 11 Jun 2007, Bharat Kumar Reddy wrote: On 6/11/07, Marc Aurele La France [EMAIL PROTECTED] wrote: On Mon, 11 Jun 2007, Bharat Kumar Reddy wrote: I have disabled the X by changing the runlevel to init 3 followed by reboot. After reboot I have issued the command scanpci -v and output is attached in scanpci.txt. Thanks. Next, let's try retrieving that BIOS ourselves. Again, before attempting to start any X server, please do, as root, ... pcitweak -r 2:4:0 0x30 You should see ... 0x8012 If so, continue with ... pcitweak -w 2:4:0 0x30 0x80120001 mmapr /dev/mem 0x8012 0x2 | gzip -9 BIOS.gz pcitweak -w 2:4:0 0x30 0x8012 ... and send me (privately, not to the list) BIOS.gz. Please be mindful of typos in the above commands. I booted the machine in init 3 runlevel, login as a superuser (root) and executed the the following commands. # pcitweak -r 2:4:0 0x30 0x8012 # pcitweak -w 2:4:0 0x30 0x80120001 # mmapr /dev/mem 0x8012 0x2 | gzip -9 BIOS.gz # pcitweak -w 2:4:0 0x30 0x8012 Please find the attached BIOS.gz file. Interesting. That adapter says it has no BIOS, which makes me think it wouldn't even work in Windows, unless a driver, very very specific to it, was provided with it. I've never seen this before. You should probably try to convince, if possible, your system BIOS to use it as it's primary display, instead of the Intel adapter, and see what happens. In any case, I doubt very much you will ever be able to make it work with X in the foreseeable future. Unless it is part of the motherboard, I'd be very interested in buying it from you. Marc. +--+--+ | Marc Aurele La France | work: 1-780-492-9310 | | Academic Information and| fax:1-780-492-1729 | |Communications Technologies | email: [EMAIL PROTECTED] | | 352 General Services Building +--+ | University of Alberta | | | Edmonton, Alberta |Standard disclaimers apply| | T6G 2H1 | | | CANADA | | +--+--+ XFree86 developer and VP. ATI driver and X server internals. ___ XFree86 mailing list XFree86@XFree86.Org http://XFree86.Org/mailman/listinfo/xfree86
Re: [XFree86] XFree86-4.6.0 for Radeon R250 M9
On Sat, 9 Jun 2007, Bharat Kumar Reddy wrote: On 6/8/07, Marc Aurele La France [EMAIL PROTECTED] wrote: On Fri, 8 Jun 2007, Bharat Kumar Reddy wrote: I am tring to configure XFree86-4.6.0 for Radeon R250 M9 . However I am seeing V_BIOS not found error. With option NoInt10 I am able to overcome this error. However I am not able to overcome the following errors: (WW) RADEON(1): Mode pool is empty (EE) RADEON(1): No valid modes found I even tried adding the horizantal and vertical refresh rate and also Modeline parameters in monitor section and no hope getting rid of this error. Can anyone help me. Attached the XFree86.log and XF86Config file. I am running FC6 on a Pentium III processor. Please forward a log without the NoInt10 option. I have removed NoInt10 option as specified. I have attached XFree86.log and XF86Config file. Earlier I have started with the attached configuration. When I ran XFree86 -xf86config /root/XF86config.new I have seen the X display coming up for Card0 (82815 CGC) only. I didn't see any display for my card1 (Radeon R250 Moblity 9000). I couldn't figure out the reason for failure in card1 inspite of success in BIOS detection. I have even tried adding the Modeline paramteres and horizantal and vertical refresh rate in Monitor Section. My monitor connected to Card1 is Acer 77c. The adapter will not function without being initialised by its BIOS, and there's not much the driver (by itself) can do about it. So the next step is to figure out why that BIOS can't be retrieved. Towards that end, please send me the output from `scanpci -v` on this system, after a powerdown-reboot, but before any attempt to start an X server. Secondly, you appear to have an incomplete installation of XFree86 4.6.0, as /usr/X11R6/lib/modules/linux/libint10.a is missing. Although I don't think this is relevant to the problem. Thanks. Marc. +--+--+ | Marc Aurele La France | work: 1-780-492-9310 | | Academic Information and| fax:1-780-492-1729 | |Communications Technologies | email: [EMAIL PROTECTED] | | 352 General Services Building +--+ | University of Alberta | | | Edmonton, Alberta |Standard disclaimers apply| | T6G 2H1 | | | CANADA | | +--+--+ XFree86 developer and VP. ATI driver and X server internals. ___ XFree86 mailing list XFree86@XFree86.Org http://XFree86.Org/mailman/listinfo/xfree86
Re: [XFree86] XFree86-4.6.0 for Radeon R250 M9
Hi Marc, I have disabled the X by changing the runlevel to init 3 followed by reboot. After reboot I have issued the command scanpci -v and output is attached in scanpci.txt. Yes you are right, int10 is missing under /usr/X11R6/lib/modules/linux. I will check it out the reason for this behaviour. Regards, -Bharat. On 6/11/07, Marc Aurele La France [EMAIL PROTECTED] wrote: On Sat, 9 Jun 2007, Bharat Kumar Reddy wrote: On 6/8/07, Marc Aurele La France [EMAIL PROTECTED] wrote: On Fri, 8 Jun 2007, Bharat Kumar Reddy wrote: I am tring to configure XFree86-4.6.0 for Radeon R250 M9 . However I am seeing V_BIOS not found error. With option NoInt10 I am able to overcome this error. However I am not able to overcome the following errors: (WW) RADEON(1): Mode pool is empty (EE) RADEON(1): No valid modes found I even tried adding the horizantal and vertical refresh rate and also Modeline parameters in monitor section and no hope getting rid of this error. Can anyone help me. Attached the XFree86.log and XF86Config file. I am running FC6 on a Pentium III processor. Please forward a log without the NoInt10 option. I have removed NoInt10 option as specified. I have attached XFree86.log and XF86Config file. Earlier I have started with the attached configuration. When I ran XFree86 -xf86config /root/XF86config.new I have seen the X display coming up for Card0 (82815 CGC) only. I didn't see any display for my card1 (Radeon R250 Moblity 9000). I couldn't figure out the reason for failure in card1 inspite of success in BIOS detection. I have even tried adding the Modeline paramteres and horizantal and vertical refresh rate in Monitor Section. My monitor connected to Card1 is Acer 77c. The adapter will not function without being initialised by its BIOS, and there's not much the driver (by itself) can do about it. So the next step is to figure out why that BIOS can't be retrieved. Towards that end, please send me the output from `scanpci -v` on this system, after a powerdown-reboot, but before any attempt to start an X server. Secondly, you appear to have an incomplete installation of XFree86 4.6.0, as /usr/X11R6/lib/modules/linux/libint10.a is missing. Although I don't think this is relevant to the problem. Thanks. Marc. +--+--+ | Marc Aurele La France | work: 1-780-492-9310 | | Academic Information and| fax:1-780-492-1729 | |Communications Technologies | email: [EMAIL PROTECTED] | | 352 General Services Building +--+ | University of Alberta | | | Edmonton, Alberta |Standard disclaimers apply| | T6G 2H1 | | | CANADA | | +--+--+ XFree86 developer and VP. ATI driver and X server internals. pci bus 0x cardnum 0x00 function 0x00: vendor 0x8086 device 0x1130 Intel Corporation 82815 815 Chipset Host Bridge and Memory Controller Hub STATUS0x2090 COMMAND 0x0006 CLASS 0x06 0x00 0x00 REVISION 0x02 BIST 0x00 HEADER 0x00 LATENCY 0x00 CACHE 0x00 pci bus 0x cardnum 0x02 function 0x00: vendor 0x8086 device 0x1132 Intel Corporation 82815 CGC [Chipset Graphics Controller] CardVendor 0x8086 card 0x0200 (Intel Corporation, Card unknown) STATUS0x02b0 COMMAND 0x0007 CLASS 0x03 0x00 0x00 REVISION 0x02 BIST 0x00 HEADER 0x00 LATENCY 0x00 CACHE 0x00 BASE0 0x9408 addr 0x9400 MEM PREFETCHABLE BASE1 0x9030 addr 0x9030 MEM MAX_LAT 0x00 MIN_GNT 0x00 INT_PIN 0x01 INT_LINE 0x09 pci bus 0x cardnum 0x1e function 0x00: vendor 0x8086 device 0x244e Intel Corporation 82801 PCI Bridge STATUS0x0080 COMMAND 0x0007 CLASS 0x06 0x04 0x00 REVISION 0x01 HEADER0x01 LATENCY 0x00 PRIBUS0x00 SECBUS 0x01 SUBBUS 0x02 SECLT 0x20 SECSTATUS 0x2280 IOBASE0x7000 IOLIM 0x8fff NOPREFETCH_MEMBASE 0x8010 MEMLIM 0x802f PREFETCH_MEMBASE 0x8040 MEMLIM 0x901f NO_FAST_B2B NO_SEC_BUS_RST NO_M_ABRT NO_VGA_EN ISA_EN NO_SERR_EN NO_PERR_EN pci bus 0x cardnum 0x1f function 0x00: vendor 0x8086 device 0x2440 Intel Corporation 82801BA ISA Bridge (LPC) STATUS0x0280 COMMAND 0x000f CLASS 0x06 0x01 0x00 REVISION 0x01 BIST 0x00 HEADER 0x80 LATENCY 0x00 CACHE 0x00 BYTE_00x01 BYTE_1 0x04 BYTE_2 0x00 BYTE_3 0x00 pci bus 0x cardnum 0x1f function 0x01: vendor 0x8086 device 0x244b Intel Corporation 82801BA IDE U100 STATUS0x0280 COMMAND 0x0005 CLASS 0x01 0x01 0x80 REVISION 0x01 BIST 0x00 HEADER 0x00 LATENCY 0x00 CACHE 0x00 BASE4 0x9c01 addr 0x9c00 I/O BYTE_00x07 BYTE_1 0xa3 BYTE_2
Re: [XFree86] XFree86-4.6.0 for Radeon R250 M9
On Fri, 8 Jun 2007, Bharat Kumar Reddy wrote: I am tring to configure XFree86-4.6.0 for Radeon R250 M9 . However I am seeing V_BIOS not found error. With option NoInt10 I am able to overcome this error. However I am not able to overcome the following errors: (WW) RADEON(1): Mode pool is empty (EE) RADEON(1): No valid modes found I even tried adding the horizantal and vertical refresh rate and also Modeline parameters in monitor section and no hope getting rid of this error. Can anyone help me. Attached the XFree86.log and XF86Config file. I am running FC6 on a Pentium III processor. Please forward a log without the NoInt10 option. Thanks. Marc. +--+--+ | Marc Aurele La France | work: 1-780-492-9310 | | Academic Information and| fax:1-780-492-1729 | |Communications Technologies | email: [EMAIL PROTECTED] | | 352 General Services Building +--+ | University of Alberta | | | Edmonton, Alberta |Standard disclaimers apply| | T6G 2H1 | | | CANADA | | +--+--+ XFree86 developer and VP. ATI driver and X server internals. ___ XFree86 mailing list XFree86@XFree86.Org http://XFree86.Org/mailman/listinfo/xfree86