Re: [gentoo-user] dma_intr: status=0x51
Hemmann, Volker Armin wrote:
On Saturday 08 October 2005 04:15, Matthias Langer wrote:
I just bought myself a new harddrive. While everything seems to work
fine so far, I recognized these messages from dmesg:
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
I'm using vanilla-sources-2.6.12.5.
Here are some other parts from dmesg, which are included to describe the
relevant hardware in detail:
SiI680: IDE controller at PCI slot :00:09.0
SiI680: chipset revision 1
SiI680: BASE CLOCK == 133
SiI680: 100% native mode on irq 10
ide0: MMIO-DMA , BIOS settings: hda:pio, hdb:pio
ide1: MMIO-DMA , BIOS settings: hdc:pio, hdd:pio
...
Probing IDE interface ide1...
hdc: _NEC DVD_RW ND-3540A, ATAPI CD/DVD-ROM drive
hdd: Maxtor 6L250R0, ATA DISK drive
hdd: max request size: 64KiB
hdd: 490234752 sectors (251000 MB) w/16384KiB Cache, CHS=30515/255/63,
UDMA(133)
hdd: cache flushes supported
Finally, this is what i get from hdparm -i /dev/hdd:
Model=Maxtor 6L250R0, FwRev=BAH41G10, SerialNo=L59CY5SH
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=16384kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null):
Maybe someone can give me a hint what might be wrong with my configuration.
first off all, you should never mix ata and atapi devices (harddisks and
opticals) on one channel. That is known for making problems.
Your error message could be have two origins: your cable is defective or not
properly seated (easy to check), or your harddisk is on its way to the great
vendor in the sky.
Get a different cable. Connect the drive with this new cable. ONLY connect the
drive, not the burner. Does the error still occurs? Bring back the harddisk,
where you bought it.
Well, I tried to connect the drive to another cable with success.
However, with this cable, which seemed to be an older one, the drive was
restricted to UDMA(33).
My theory about these messages now is the following:
The HD I'm talking about is not directly connected to the ide-cable, but
via a rather old 'HD-Box'. Thus I have:
Controller-Modern IDE-Cable-HD-Box-Old IDE-Cable-HD.
I think that the 'Old IDE-Cable' part is causing the troubles. However I
can't verify that without rearranging a bulk of ide-drives.
I'll buy myself a new box and tell you about the results.
Thanks for your hints, Matthias
--
gentoo-user@gentoo.org mailing list
Re: [gentoo-user] dma_intr: status=0x51
Matthias Langer wrote:
Hemmann, Volker Armin wrote:
On Saturday 08 October 2005 04:15, Matthias Langer wrote:
I just bought myself a new harddrive. While everything seems to work
fine so far, I recognized these messages from dmesg:
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
I'm using vanilla-sources-2.6.12.5.
Here are some other parts from dmesg, which are included to describe
the
relevant hardware in detail:
SiI680: IDE controller at PCI slot :00:09.0
SiI680: chipset revision 1
SiI680: BASE CLOCK == 133
SiI680: 100% native mode on irq 10
ide0: MMIO-DMA , BIOS settings: hda:pio, hdb:pio
ide1: MMIO-DMA , BIOS settings: hdc:pio, hdd:pio
...
Probing IDE interface ide1...
hdc: _NEC DVD_RW ND-3540A, ATAPI CD/DVD-ROM drive
hdd: Maxtor 6L250R0, ATA DISK drive
hdd: max request size: 64KiB
hdd: 490234752 sectors (251000 MB) w/16384KiB Cache, CHS=30515/255/63,
UDMA(133)
hdd: cache flushes supported
Finally, this is what i get from hdparm -i /dev/hdd:
Model=Maxtor 6L250R0, FwRev=BAH41G10, SerialNo=L59CY5SH
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=16384kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null):
Maybe someone can give me a hint what might be wrong with my
configuration.
first off all, you should never mix ata and atapi devices (harddisks
and opticals) on one channel. That is known for making problems.
Your error message could be have two origins: your cable is defective
or not properly seated (easy to check), or your harddisk is on its
way to the great vendor in the sky.
Get a different cable. Connect the drive with this new cable. ONLY
connect the drive, not the burner. Does the error still occurs? Bring
back the harddisk, where you bought it.
Well, I tried to connect the drive to another cable with success.
However, with this cable, which seemed to be an older one, the drive
was restricted to UDMA(33).
My theory about these messages now is the following:
The HD I'm talking about is not directly connected to the ide-cable,
but via a rather old 'HD-Box'. Thus I have:
Controller-Modern IDE-Cable-HD-Box-Old IDE-Cable-HD.
I think that the 'Old IDE-Cable' part is causing the troubles. However
I can't verify that without rearranging a bulk of ide-drives.
I'll buy myself a new box and tell you about the results.
Well, it was as I expected. After switching to an UDMA(133) compatible
mobile rack the error messages are gone.
Thanks for your hints, Matthias
--
gentoo-user@gentoo.org mailing list
[gentoo-user] dma_intr: status=0x51
I just bought myself a new harddrive. While everything seems to work
fine so far, I recognized these messages from dmesg:
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
I'm using vanilla-sources-2.6.12.5.
Here are some other parts from dmesg, which are included to describe the
relevant hardware in detail:
SiI680: IDE controller at PCI slot :00:09.0
SiI680: chipset revision 1
SiI680: BASE CLOCK == 133
SiI680: 100% native mode on irq 10
ide0: MMIO-DMA , BIOS settings: hda:pio, hdb:pio
ide1: MMIO-DMA , BIOS settings: hdc:pio, hdd:pio
...
Probing IDE interface ide1...
hdc: _NEC DVD_RW ND-3540A, ATAPI CD/DVD-ROM drive
hdd: Maxtor 6L250R0, ATA DISK drive
hdd: max request size: 64KiB
hdd: 490234752 sectors (251000 MB) w/16384KiB Cache, CHS=30515/255/63,
UDMA(133)
hdd: cache flushes supported
Finally, this is what i get from hdparm -i /dev/hdd:
Model=Maxtor 6L250R0, FwRev=BAH41G10, SerialNo=L59CY5SH
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=16384kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null):
Maybe someone can give me a hint what might be wrong with my configuration.
Thanks, Matthias
--
gentoo-user@gentoo.org mailing list
Re: [gentoo-user] dma_intr: status=0x51
On Saturday 08 October 2005 04:15, Matthias Langer wrote:
I just bought myself a new harddrive. While everything seems to work
fine so far, I recognized these messages from dmesg:
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
I'm using vanilla-sources-2.6.12.5.
Here are some other parts from dmesg, which are included to describe the
relevant hardware in detail:
SiI680: IDE controller at PCI slot :00:09.0
SiI680: chipset revision 1
SiI680: BASE CLOCK == 133
SiI680: 100% native mode on irq 10
ide0: MMIO-DMA , BIOS settings: hda:pio, hdb:pio
ide1: MMIO-DMA , BIOS settings: hdc:pio, hdd:pio
...
Probing IDE interface ide1...
hdc: _NEC DVD_RW ND-3540A, ATAPI CD/DVD-ROM drive
hdd: Maxtor 6L250R0, ATA DISK drive
hdd: max request size: 64KiB
hdd: 490234752 sectors (251000 MB) w/16384KiB Cache, CHS=30515/255/63,
UDMA(133)
hdd: cache flushes supported
Finally, this is what i get from hdparm -i /dev/hdd:
Model=Maxtor 6L250R0, FwRev=BAH41G10, SerialNo=L59CY5SH
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=16384kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null):
Maybe someone can give me a hint what might be wrong with my configuration.
first off all, you should never mix ata and atapi devices (harddisks and
opticals) on one channel. That is known for making problems.
Your error message could be have two origins: your cable is defective or not
properly seated (easy to check), or your harddisk is on its way to the great
vendor in the sky.
Get a different cable. Connect the drive with this new cable. ONLY connect the
drive, not the burner. Does the error still occurs? Bring back the harddisk,
where you bought it.
--
gentoo-user@gentoo.org mailing list
