date:20140813

Re: [Elphel-support] how to dump code into camera

2014-08-13 Thread gaurav dasondhi

QUESTION

IN ISE WEBPACK DURING IMPLMENT DESIGN I GOT SOME ERRORS. DESIGN SUMMARY AND
ERRORS ARE GIVEN BLOW.

Target Device:

xc3s1200e-5ft256

Product Version:

ISE 12.1

- Warnings:

836 Warnings (1 new) E:/x353original\_xmsgs/*.xmsgs?DataKey=Warning

- Errors:

X 6 Errors (2 new) E:/x353original\_xmsgs/*.xmsgs?DataKey=Error

I GOT THESE 6 EROORS PLEASE PROVIDE SOLUTION.

1.ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
i_compressor/i_quantizator/i_zigzag/i_z5 has a hexadecimal value,
111011001000, which is too large. INIT should
contain a
maximum of 32 bits.
ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
i_compressor/i_quantizator/i_zigzag/i_z4 has a hexadecimal value,
10001100100110110110, which is too large. INIT should
contain a
maximum of 32 bits.
ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
i_compressor/i_quantizator/i_zigzag/i_z3 has a hexadecimal value,
01001010010011011000, which is too large. INIT should
contain a
maximum of 32 bits.
ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
i_compressor/i_quantizator/i_zigzag/i_z2 has a hexadecimal value,
011000110101001000100110, which is too large. INIT should
contain a
maximum of 32 bits.
ERROR:LIT:239 - Attribute INIT on ROM32X1 instance
i_compressor/i_quantizator/i_zigzag/i_z1 has an invalid hexadecimal
value,
h611A7896.
ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
i_compressor/i_quantizator/i_zigzag/i_z0 has a hexadecimal value,
11000110011100110001100111001100, which is too large. INIT should
contain a
maximum of 32 bits.

On Tue, Aug 12, 2014 at 3:58 PM, gaurav dasondhi
gauravdasondhi2...@gmail.com wrote:

Dear oleg
clarify it : bad bitstream can cause losing connection or
damaging the hardware. here damaging hardware means ??

so if i used bad bitstream , then is there any way to keep
camera again to its default setting.?

On Tue, Aug 12, 2014 at 1:03 AM, Oleg support-list@support.elphel.com
wrote:

Guarav,

1. i want to perform correlation between two images ,i have a code
written in verilog but how to dump that code into camera??

If you have a single lens camera (NC353, NC353-... - meaning there's no
10359 board installed that has an extra fpga) :

The src verilog files for the system board fpga are here:
http://elphel.cvs.sourceforge.net/viewvc/elphel/elphel353-8.0/fpga/x3x3/
In short, you need to add your code to the project, but most likely it
won't fit in the fpga or won't meet the timing the fpga on the system board
is almost full.

If you manage to create a bitstream - it should be called x353.bit and
copied it to the camera /etc/ - after rebooting the fpga will be configured
with a new bitstream.
If the camera doesn't have the serial output port on the side (NC353-369)
- it will be hard to debug possible problems - bad bitstream can cause
losing connection or damaging the hardware.

2. is iverilog 0.9.5-1 will work instead of 0.9.3 and is we need to
install icraus verilog as we already have ISE WEBPACK.??

iverilog 0.9.5-1 should work - never tested though. For verilog
verification you can use both ISE Webpack or Icarus Verilog + GTKWave.

3. i installed mplayer by command line but as i typed : mplayer rtsp://
192.168.0.9:554 -vo x11 -fs -zoom then camera is in working mode but we
got blurred image??

Blurred - compared to http://192.168.0.9:8081/bimg?

*SO WHAT I DID IS IT OK OR I NEED TO INSTALL SOMETHING ELSE *

For verilog:
ISE Webpack, Icarus and GTKWave

For the camera software:
cross-compiler, get the camera firmware built from cvs
http://wiki.elphel.com/index.php?title=Elphel_Software_Kit_for_Ubuntu#Build_Elphel_Software
-
then you can modify sources and rebuild it. KDevelop makes it easier to
navigate through the project.
Building the firmware requires to have the NFS server set up.

ImageJ plugins are mostly for our calibrated/stereo/multi-sensor cameras.
You can use them as a base to write your own plugin for correlation, for
example.

Best regards,
Oleg Dzhimiev
Electronics Engineer
phone: +1 801 783 x124
Elphel, Inc.

___
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

Re: [Elphel-support] how to dump code into camera

2014-08-13 Thread Oleg

Hi,

Is it during synthesis or implementation?

I think the last time it was built it was ISE WebPack 9.1 or 10.1 - and was
ok. 14.7 looks like working as well. I check the Synthesis only.

You can try:
change all ROM32X1 instances:

ROM32X1 i_z0 ( .A0(rom_a[0]), .A1(rom_a[1]), .A2(rom_a[2]), .A3(rom_a[3]),
.A4(rom_a[4]), .O(rom_q[0]));
...
defparam i_z0.INIT = 32'hC67319CC;

to:

ROM32X1 (.INIT(32'hC67319CC)) i_z0 ( .A0(rom_a[0]), .A1(rom_a[1]),
.A2(rom_a[2]), .A3(rom_a[3]), .A4(rom_a[4]), .O(rom_q[0]));

On 13 August 2014 02:25, gaurav dasondhi gauravdasondhi2...@gmail.com
wrote:

QUESTION

IN ISE WEBPACK DURING IMPLMENT DESIGN I GOT SOME ERRORS. DESIGN SUMMARY
AND ERRORS ARE GIVEN BLOW.

Target Device:

xc3s1200e-5ft256

Product Version:

ISE 12.1

- Warnings:

836 Warnings (1 new)

- Errors:

X 6 Errors (2 new)

I GOT THESE 6 EROORS PLEASE PROVIDE SOLUTION.

On Tue, Aug 12, 2014 at 3:58 PM, gaurav dasondhi
gauravdasondhi2...@gmail.com wrote:

Dear oleg
clarify it : bad bitstream can cause losing connection or
damaging the hardware. here damaging hardware means ??

so if i used bad bitstream , then is there any way to keep
camera again to its default setting.?

On Tue, Aug 12, 2014 at 1:03 AM, Oleg support-list@support.elphel.com
wrote:

Guarav,

1. i want to perform correlation between two images ,i have a code
written in verilog but how to dump that code into camera??

If you have a single lens camera (NC353, NC353-... - meaning there's no
10359 board installed that has an extra fpga) :

If you manage to create a bitstream - it should be called x353.bit and
copied it to the camera /etc/ - after rebooting the fpga will be configured
with a new bitstream.
If the camera doesn't have the serial output port on the side
(NC353-369) - it will be hard to debug possible problems - bad bitstream
can cause losing connection or damaging the hardware.

2. is iverilog 0.9.5-1 will work instead of 0.9.3 and is we need to
install icraus verilog as we already have ISE WEBPACK.??

iverilog 0.9.5-1 should work - never tested though. For verilog
verification you can use both ISE Webpack or Icarus Verilog + GTKWave.

3. i installed mplayer by command line but as i typed : mplayer rtsp://
192.168.0.9:554 -vo x11 -fs -zoom then camera is in working mode but
we got blurred image??

Blurred - compared to http://192.168.0.9:8081/bimg?

*SO WHAT I DID IS IT OK OR I NEED TO INSTALL SOMETHING ELSE *

For verilog:
ISE Webpack, Icarus and GTKWave

ImageJ plugins are mostly for our calibrated/stereo/multi-sensor
cameras. You can use them as a base to write your own plugin for
correlation, for example.

Best regards,
Oleg Dzhimiev
Electronics Engineer
phone: +1 801 783 x124
Elphel, Inc.

___
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

--
Best regards,
Oleg

Re: [Elphel-support] how to dump code into camera

2014-08-13 Thread gaurav dasondhi

Hi

after synthesis i got some warnings as i mentioned in previous mail

*AFTER IMPLEMENT DESIGN: OUTPUT*

ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
   i_compressor/i_quantizator/i_zigzag/i_z5 has a hexadecimal value,
   111011001000, which is too large. INIT should
contain a
   maximum of 32 bits.
ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
   i_compressor/i_quantizator/i_zigzag/i_z4 has a hexadecimal value,
   10001100100110110110, which is too large. INIT should
contain a
   maximum of 32 bits.
ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
   i_compressor/i_quantizator/i_zigzag/i_z3 has a hexadecimal value,
   01001010010011011000, which is too large. INIT should
contain a
   maximum of 32 bits.
ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
   i_compressor/i_quantizator/i_zigzag/i_z2 has a hexadecimal value,
   011000110101001000100110, which is too large. INIT should
contain a
   maximum of 32 bits.
ERROR:LIT:239 - Attribute INIT on ROM32X1 instance
   i_compressor/i_quantizator/i_zigzag/i_z1 has an invalid hexadecimal
value,
   h611A7896.
ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
   i_compressor/i_quantizator/i_zigzag/i_z0 has a hexadecimal value,
   11000110011100110001100111001100, which is too large. INIT should
contain a
   maximum of 32 bits.

*AS YOU SUGGESTED IN PREVIOUS MAIL *:

change all ROM32X1 instances:

 ROM32X1 i_z0 ( .A0(rom_a[0]), .A1(rom_a[1]), .A2(rom_a[2]), .A3(rom_a[3]),
 .A4(rom_a[4]), .O(rom_q[0]));
 ...
 defparam i_z0.INIT = 32'hC67319CC;

to:

 ROM32X1 (.INIT(32'hC67319CC)) i_z0 ( .A0(rom_a[0]), .A1(rom_a[1]),
 .A2(rom_a[2]), .A3(rom_a[3]), .A4(rom_a[4]), .O(rom_q[0]));


*IT IS LOOK LIKE*

   ROM32X1(.INIT(32'hC67319CC)) i_z0 ( .A0(rom_a[0]), .A1(rom_a[1]),
.A2(rom_a[2]), .A3(rom_a[3]), .A4(rom_a[4]), .O(rom_q[0]));
   ROM32X1(.INIT(32'h611A7896)) i_z1 ( .A0(rom_a[0]), .A1(rom_a[1]),
.A2(rom_a[2]), .A3(rom_a[3]), .A4(rom_a[4]), .O(rom_q[1]));
   ROM32X1(.INIT(32'h6357A260)) i_z2 ( .A0(rom_a[0]), .A1(rom_a[1]),
.A2(rom_a[2]), .A3(rom_a[3]), .A4(rom_a[4]), .O(rom_q[2]));
   ROM32X1(.INIT(32'h4A040C18)) i_z3 ( .A0(rom_a[0]), .A1(rom_a[1]),
.A2(rom_a[2]), .A3(rom_a[3]), .A4(rom_a[4]), .O(rom_q[3]));
   ROM32X1(.INIT(32'h8C983060)) i_z4 ( .A0(rom_a[0]), .A1(rom_a[1]),
.A2(rom_a[2]), .A3(rom_a[3]), .A4(rom_a[4]), .O(rom_q[4]));
   ROM32X1(.INIT(32'hF0E0C080)) i_z5 ( .A0(rom_a[0]), .A1(rom_a[1]),
.A2(rom_a[2]), .A3(rom_a[3]), .A4(rom_a[4]), .O(rom_q[5]));

*OUTPUT ERROR : DURING SYTHESIS*

ERROR:HDLCompilers:26 - quantizator353.v line 368 expecting ';', found
'i_z0'
ERROR:HDLCompilers:26 - quantizator353.v line 368 expecting 'endmodule',
found '('






On Thu, Aug 14, 2014 at 2:46 AM, Oleg support-list@support.elphel.com
wrote:

 Hi,

 Is it during synthesis or implementation?

 I think the last time it was built it was ISE WebPack 9.1 or 10.1 - and
 was ok. 14.7 looks like working as well. I check the Synthesis only.

 You can try:
 change all ROM32X1 instances:

 ROM32X1 i_z0 ( .A0(rom_a[0]), .A1(rom_a[1]), .A2(rom_a[2]),
 .A3(rom_a[3]), .A4(rom_a[4]), .O(rom_q[0]));
 ...
 defparam i_z0.INIT = 32'hC67319CC;

 to:

 ROM32X1 (.INIT(32'hC67319CC)) i_z0 ( .A0(rom_a[0]), .A1(rom_a[1]),
 .A2(rom_a[2]), .A3(rom_a[3]), .A4(rom_a[4]), .O(rom_q[0]));




 On 13 August 2014 02:25, gaurav dasondhi gauravdasondhi2...@gmail.com
 wrote:

 Hi

 QUESTION

 IN ISE WEBPACK DURING IMPLMENT DESIGN I GOT SOME ERRORS. DESIGN SUMMARY
 AND ERRORS ARE GIVEN BLOW.

   Target Device:

 xc3s1200e-5ft256

 Product Version:

 ISE 12.1

- Warnings:

  836 Warnings (1 new)

- Errors:

  X 6 Errors (2 new)


 I GOT THESE 6 EROORS PLEASE PROVIDE SOLUTION.


 1.ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
i_compressor/i_quantizator/i_zigzag/i_z5 has a hexadecimal value,
111011001000, which is too large. INIT should
 contain a
maximum of 32 bits.
 ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
i_compressor/i_quantizator/i_zigzag/i_z4 has a hexadecimal value,
10001100100110110110, which is too large. INIT should
 contain a
maximum of 32 bits.
 ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
i_compressor/i_quantizator/i_zigzag/i_z3 has a hexadecimal value,
01001010010011011000, which is too large. INIT should
 contain a
maximum of 32 bits.
 ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
i_compressor/i_quantizator/i_zigzag/i_z2 has a hexadecimal value,
011000110101001000100110, which is too large. INIT should
 contain a
maximum of 32 bits.
 ERROR:LIT:239 - Attribute INIT on ROM32X1 instance
i_compressor/i_quantizator/i_zigzag/i_z1 has an invalid hexadecimal
 value,
h611A7896.
 ERROR:LIT:241 - Attribute INIT on ROM32X1 instance
i_compressor/i_quantizator/i_zigzag/i_z0 has a hexadecimal value,
11000110011100110001100111001100, which is too large. INIT should
 contain a
maximum of 32 bits.

Re: [Elphel-support] how to dump code into camera

Re: [Elphel-support] how to dump code into camera

Re: [Elphel-support] how to dump code into camera

3 matches

Site Navigation

Mail list logo

Footer information