[time-nuts] A Lady H mystery
I don't think Heather v5.0 ever worked with the ACE-III. Heather uses the TSIP primary and secondary timing messages to drive the display. The ACE-III (and SV6) don't output those messages. The next release of Heather has SV6 support and also supports the Trimble TAIP protocol that these receivers can also support. Those receivers can also speak NMEA... perhaps your receiver had been configured for NMEA until the power blew? ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
Re: [time-nuts] A Lady H mystery
polarized tantalum in correctly? Regards, Jerry > On Dec 19, 2017, at 2:20 PM, Dan Raewrote: > > I've been trying to get LH (V5) to control and set position for the GPS board > in one of my GPSDOs. It is a Trimble "Lassen Ace III" Rx according to > itself. LH auto detects it quickly enough, reports it as a TSIP receiver but > then shows a screen saying "LOG: OFF", a blank graph grid and nothing much > else. No data apparently, so how did it autodetect? > > I've been beating my head against this for two days; it used to work fine but > since a tantalum went on the TTL to RS232 convertor (since replaced along > with the receiver itself just in case) it won't perform for me. LH performs > fine for all the other units here as it always has and the Trimble Monitor > program works on this one. > > I'd really appreciate someone telling me gently what stupid thing I'm doing > or not doing :^) > > Thanks, > > Dan - ac6ao > > ___ > time-nuts mailing list -- time-nuts@febo.com > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
Re: [time-nuts] A Lady H mystery
I had similar symptoms with LH and T-Bolt. The cause was the serial port. As I change the serial port HW on computer site - T-Bolt was back to track. it was interesting enough that other devices was OK with initial Serial port HW. On 2017-12-19 17:20, Dan Rae wrote: I've been trying to get LH (V5) to control and set position for the GPS board in one of my GPSDOs. It is a Trimble "Lassen Ace III" Rx according to itself. LH auto detects it quickly enough, reports it as a TSIP receiver but then shows a screen saying "LOG: OFF", a blank graph grid and nothing much else. No data apparently, so how did it autodetect? I've been beating my head against this for two days; it used to work fine but since a tantalum went on the TTL to RS232 convertor (since replaced along with the receiver itself just in case) it won't perform for me. LH performs fine for all the other units here as it always has and the Trimble Monitor program works on this one. I'd really appreciate someone telling me gently what stupid thing I'm doing or not doing :^) Thanks, Dan - ac6ao ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. -- WBW, V.P. ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
[time-nuts] A Lady H mystery
I've been trying to get LH (V5) to control and set position for the GPS board in one of my GPSDOs. It is a Trimble "Lassen Ace III" Rx according to itself. LH auto detects it quickly enough, reports it as a TSIP receiver but then shows a screen saying "LOG: OFF", a blank graph grid and nothing much else. No data apparently, so how did it autodetect? I've been beating my head against this for two days; it used to work fine but since a tantalum went on the TTL to RS232 convertor (since replaced along with the receiver itself just in case) it won't perform for me. LH performs fine for all the other units here as it always has and the Trimble Monitor program works on this one. I'd really appreciate someone telling me gently what stupid thing I'm doing or not doing :^) Thanks, Dan - ac6ao ___ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.