Good luck!
Luis Morales
On Fri, Sep 19, 2008 at 9:04 PM, Dae Yeung Um [EMAIL PROTECTED] wrote:
It's a Digium TE121P with Echo Cancellation
Zapata.conf
# Span 1: WCT1/0 Wildcard TE121 Card 0 HDB3/CCS/CRC4 RED RECOVERING
span=1,1,0,ccs,hdb3
cas=1-15:1101
dchan=16
cas=17-31:1101
# Span 2
Hello Humberto
It's cas actually...
Ccs was a transcription mistake.
Thank you
DAE
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Humberto
Figuera
Sent: Thursday, September 18, 2008 8:52 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
be we can meet there and
take a cup of coffee!! I'll try to attend your session. Looks very
interesting.
Thank you again.
DAE YEUNG UM
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Moises Silva
Sent: Thursday, September 18, 2008 1:53 PM
To: Asterisk
: [asterisk-users] Help with MFC/R2
Not really the unicall setup must be idem. So you can see the unicall
channels ?
It's moises are busy i can give you support too
Regards,
Luis Morales
On Sat, Sep 20, 2008 at 12:15 PM, Dae Yeung Um [EMAIL PROTECTED] wrote:
Hi Luis,
But this E1 has 30 channels
, Sep 18, 2008 at 11:49 PM, Dae Yeung Um [EMAIL PROTECTED] wrote:
In fact I see 1101 in the rx bits on all channels...
But I have in parallel one old Panasonic Key Phone system (Actually in
production, to be replaced by asterisk), and it's works perfectly and
immediately once I pass the E1 cables
calls
16-30: for incomming calls
?
Now for make calls your telephone company must be provide MFC-R2
signaling. In your case the logs files show an invalid signal on make
call.
Regards,
Luis Morales
On Fri, Sep 19, 2008 at 10:10 AM, Dae Yeung Um [EMAIL PROTECTED] wrote:
Hello
I got:
[Sep 17
.
Told me more about your hardware:
- E1 cards
- How did you do to connect E1 interface to E1 asterisk's card ?
- You can receive calls ?
Please send us zapata.conf and unicall.conf
Regards,
Luis Morales
On Fri, Sep 19, 2008 at 12:46 PM, Dae Yeung Um [EMAIL PROTECTED] wrote:
All channels 1~15
Anyone has any Idea why I can't place or receive a call?
Your help will be really appreciated!
DAE YEUNG UM
___
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
AstriCon 2008 - September 22 - 25 Phoenix, Arizona
already open the zap device, most likely
Asterisk. Just one application at a given time can open a zap device.
You cannot run testcall and Asterisk at the same time unless you make
sure they don't try to open the same channels.
Moy
On Wed, Sep 17, 2008 at 1:27 AM, Dae Yeung Um [EMAIL PROTECTED] wrote
and if you see 1101 in the rx bits, it means the telco
(or whatever you have in the other end) has blocked their side. If
this is a telco line you need to call them and tell them to unblock
your lines.
On Wed, Sep 17, 2008 at 10:33 PM, Dae Yeung Um [EMAIL PROTECTED] wrote:
Thank you for the reply
10 matches
Mail list logo