I asked this a while ago and now had an out look crash so lost the
information.
Does anyone know where to obtain a thing called a click rule.
Thanks, Phil Parr.
[Non-text portions of this message have been removed]
To listen to the show archives go to link
Dale,
Well, depending on what method they use you can probably say goodbye to
your sprinklers... (LOL)
I had forgotten about the folks who come and take plugs out of the ground.
We had that done once to our yard in Denver and I can not say that it helped
all that much.
Lmy wallet was a little
Tongue oil is a very handy thing to use. You can mix stain with it and
achieve the exact degree of stain you want.
Works really well.
Cy, the Ancient Okie...
-Original Message-
From: blindhandyman@yahoogroups.com [mailto:[EMAIL PROTECTED]
On Behalf Of Geoff Eden
Sent: Thursday, August
Thanks, sounds like I will try to find someone to do it for me. My yard is
about 9000 sq ft. So hopefully I don't get hit in the wallet to bad.
Thanks,
Mike
-Original Message-
From: blindhandyman@yahoogroups.com [mailto:[EMAIL PROTECTED]
On Behalf Of clifford
Sent: Thursday, August
Phil, the NFB store has what I believe you're looking for. These are accurate
to 1/16 inch, very nice tool.
Bill Stephan
Kansas City, MO
(816)803-2469
William Stephan
-Original Message-
From: Phil Parr[EMAIL PROTECTED]
Sent: 9/1/06 1:31:09 AM
To: list
That is good for regular finishing! but for a cutting board, Tongue oil is
the best! It is non-toxic!
- Original Message -
From: Robert J. Moore [EMAIL PROTECTED]
To: blindhandyman@yahoogroups.com
Sent: Friday, September 01, 2006 2:21 PM
Subject: RE: [BlindHandyMan] Finishing a
Hi
Well I have been thinking about buying a Drill Doctor for some time and I
took the plunge and bought one.
I really needed it to service the 150 drills I counted and that does not
include my masonry drills.
There is two sets of drills I can not put my hands on at the moment I need
to find to
The aeration only goes about 1/2 inch into the ground, unless there is a
sprinkler head there that they hit, you shouldn't have any problems.
Jeff and Max in South Dakota!
-Original Message-
From: blindhandyman@yahoogroups.com [mailto:[EMAIL PROTECTED]
Behalf Of Cy Selfridge
Sent: Friday,
Hi
I bought the 300dd you do not need sight because the set up arms grab
the drill in the set up port and as long as you have the drill pushed in
and turn it to lock then it is in the correct position to tighten the
chuck before removing
You then put it into the cutting port and turn it to the
Hi Rae,
Have you used it with masonry bits? and how did it do with them?
Masonry bits are very differently shaped, no under-cut, and the carbide
tipped ones are very hard. Just curious, big masonry bits are very expensive
and they do grind badly when drilling.
Thanks.
Dale Leavens, Cochrane
Hi Robert,
Linseed oil is a fine finish and, except that it might impart some taste to
foods would probably be all right to start with however it is a vegetable
oil and therefore will host bacteria and possibly even other beasties. It
can also go rancid. Otherwise, I use it for a lot of things
Has anyone here used a rat zapper?
[Non-text portions of this message have been removed]
To listen to the show archives go to link
http://acbradio.org/handyman.html
or
ftp://ftp.acbradio.org/acbradio-archives/handyman/
The Pod Cast address for the Blind Handy Man Show is.
Hi Dale
I am going to sharpen my masonry bits later on today I will let you know
whether it is successful or I have destroyed my machine.
There is one in particular needs my attention because it hit some
reinforcing mesh in the cement when I was locking down the frame I made
for my air
Hi Dale
I have just sharpened my Masonry Bits no problems the secret is setting up
correctly in the set up port before sharpening.
It cut a clean sharp edge I was surprised how easy it all turned out.
ray
- Original Message -
From: Dale Leavens [EMAIL PROTECTED]
To:
Hi gang I have a 1 by 11 by 8 foot board that I need to cut for some
shelves.
I do not have a cercular saw. all I have is a hand saw which I really do not
want to use for this project. I also have a small table saw. I don't know
the size of the table saw but suffice it to say it is not a large
You certainly can cut it with a table saw and probably about as accurately
as you would be able to do with a circular saw unless you made a very good
jig.
A small table complicates the task particularly if you are cutting only a
short piece off, the closer to the middle you are cutting the
16 matches
Mail list logo
