New line card inserted about a week ago, along with a new 10g service. Last
night the LC crashed with the following;
000504: May 17 03:41:24.011 CDT: %CONST_DIAG-SP-3-HM_TEST_FAIL: Module 4
TestMacNotification consecutive failure count:5
000505: May 17 03:41:24.015 CDT:
We are working on setting up a test where we run a GRE tunnel across the
Internet, put OSPF between the tunnel and inject routes.
I can get OSPF to form an adjacency but i cannot get routes to
redistribute, nor inject by a network statement.
Anyone do such ? Any help or suggestions would be
these documents can be helpful.
http://www.cisco.com/image/gif/paws/41940/dmvpn.pdf
http://www.cisco.com/image/gif/paws/29240/dcmvpn.pdf
Alberto
-Original Message-
From: cisco-nsp-boun...@puck.nether.net [mailto:
cisco-nsp-boun...@puck.nether.net] On Behalf Of Chris Lane
Sent: December
We do not run IPv6 currently from this site, ipv6 is not enabled on box.
when i ping google.com i get the following response.
ping google.com
Translating google.com...domain server (64.17.248.2) [OK]
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001:4860:4001:800::100E,
All
I have 2 7600s directly connected ~ interfaces are Layer3 (IP) ospf/bgp
protocols running acroos
Loopbacks configured,
version: s72033-advipservicesk9_wan-mz.122-33.SXH7.bin
here is where i am messing up.
i created a vlan x
put my cross connects in here.
but the VC is down..
my ldp
running a 7600 with s72033-advipservicesk9_wan-mz.122-33.SXH7
actually just installed device, added crypto key rsa ~ all normal here,
noting unusual to report.
but, oddly this is what i am seeing when i try and ssh to box.
The remote system refused the connection.
I have loaded ssh to 100s of
on the client?
On Thu, Feb 23, 2012 at 2:56 PM, Chris Lane clane1...@gmail.com wrote:
running a 7600 with s72033-advipservicesk9_wan-mz.122-33.SXH7
actually just installed device, added crypto key rsa ~ all normal here,
noting unusual to report.
but, oddly this is what i am seeing when i try
Hello
If you have the following physical scenario
custABROCADE CER--CISCO ROUTER--BROCADE CER---custA
When i build a Virtue Lease Lines on the Brocades will this traverse through
the Cisco router? I am not sure How to configure the Cisco for LSP
signalling so the packets can
We are running a dual stack 3750
running c3750-advipservicesk9-mz.122-35.SE2.bin code.
I just started receiving this High CPU ~ i can't find much info on a HPM
main process.. Any help would be appreciated.
dr.lax0001.D.ca#sh processes cpu sorted | e 0.0
CPU utilization for five seconds: 65%/1%;
All
I have a problem with my 3750 which i have inserted here:
*write*
*startup-config file open failed (Device or resource busy)*
*
*
I have looked up and see you clear a particular line where the idea is
another user has locked up the nvram.
i don't have another user logged into my router:
sh
I am running c3750-advipservicesk9-mz.122-35.SE2 on a 3750 TS, i have a few
bgp neighbors running. Bringing a new customer session online getting this
error:
BGP:x.x.x.x open failed: Connection timed out; remote host not responding,
open active delayed 27729ms (35000ms max, 28% jitter).
I have
to match the ip they are using for
their update source?
Seeing the configs would help a lot..
On 16 September 2010 19:53, John Neiberger jneiber...@gmail.com wrote:
On Thu, Sep 16, 2010 at 12:39 PM, Chris Lane clane1...@gmail.com wrote:
I am running c3750-advipservicesk9-mz.122-35.SE2 on a 3750
All,
Running a C3750 48TS on 12.2(35)SE2 . Used very simple AAA method for
authentication with radius, 4 lines of AAA.
Happened to log into router today only to notice that i can't configure
device, my credentials don't match and i have this in the log
%AAA-3-BADMETHOD
This entry is on AUG 2nd,
All,
I have a 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX on a 6509
running s72033-advipservicesk9_wan-mz.122-33.SXH7.bin
Interface built as layer3 with a p2p site to site
experiencing tons of Input queue drops but no other errors on port.
cr.nyc1.ny#sh int g3/2
GigabitEthernet3/2 is
patterns that will be seen here.
You may also want to check the output of 'show fabric'..
- Jared
On Jul 21, 2010, at 11:58 AM, Chris Lane wrote:
All,
I have a 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX on a 6509
running s72033-advipservicesk9_wan-mz.122-33.SXH7.bin
All,
I am configuring an MPLS peer between devices.
I am forcing the 6509 globally to use LDP as the protocol and also now have
forced the interface
mpls label protocol ldp
mpls ip
the same.
yet when the LDP neighbor session come UP i get a this in logs:
TAGCON-3-TDPID TDP Id/Addr mapping
We are an ISP and have many customer neighbor sessions on our router. One of
my customers BGP sessions started flapping yesterday. The bridge we have to
them has no errors or disconnects. So i debugged the bgp session and
recieved the following. Also to note the customer router is a Juniper.
FYI:
this helps
Billy
Chris Lane wrote:
We are an ISP and have many customer neighbor sessions on our router. One
of
my customers BGP sessions started flapping yesterday. The bridge we have
to
them has no errors or disconnects. So i debugged the bgp session and
recieved the following. Also
Wanted to close out issue, customer had a memory and broadcast issue from
their Own customer.
Thanks to all
On Tue, May 25, 2010 at 9:30 AM, Chris Lane clane1...@gmail.com wrote:
I had an extended ping going to customer IP during our troubleshooting and
i never lost a packet or had loss when
Thank you Peter, problem i don't have the option to use Auto Qos on
interface, which i believe to be a line card issue or Ios.
still trying to determine.
Regards,
Chris
On Thu, May 20, 2010 at 6:07 PM, Peter Rathlev pe...@rathlev.dk wrote:
On Thu, 2010-05-20 at 13:53 -0400, Chris Lane wrote
All,
I need to run Auto QoS for a Cisco soft phone on a 6509 running IOS
122-33.SXH1
according to the cisco docs this feature was released with this train and
later.
i believe its my line cards which are:
1 48 48-port 10/100 mb RJ45 WS-X6148-45AF
SAL085281YQ
2 48 48 port
we currently have at least 40 Cisco 3750s as our distribution platform. I am
starting to move away from the 3750 and onto the 6509. Building my first
config, which is transitioning the 3750 to the 6500, i cannot use vlan
1007-1300 (which i currently do use in the 3750) due to it
Can't modify
,
On Sat, Apr 17, 2010 at 12:32:52PM -0400, Chris Lane wrote:
we currently have at least 40 Cisco 3750s as our distribution platform. I
am
starting to move away from the 3750 and onto the 6509. Building my first
config, which is transitioning the 3750 to the 6500, i cannot use vlan
1007-1300
again - this might be interesting for other readers
as well, so it's useful to keep the list in CC:)
On Sat, Apr 17, 2010 at 01:21:32PM -0400, Chris Lane wrote:
Router#sh vlan internal usage
[..]
I need all these vlans, how do i remove the above to make available?
I also had ascending
Hello,
I have all the sudden taken extremely high CPU:
sh proc cpu sorted | e 0.0
CPU utilization for five seconds: 99%/27%; one minute: 95%; five minutes:
92%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
251 2985921 15274 195490 39.29% 11.05% 6.01% 0
sh spanning-tree
No spanning tree instance exists.
sh controllers cpu-interface
ASICRxbiterr RxunderFwdctfix Txbuflos Rxbufloc Rxbufdrain
-
ASIC0 0 0 0 0 0 0
and router
(Pavel Dimow)
4. Cisco 3750 High CPU (Chris Lane)
5. Re: Cisco 3750 High CPU (Luan Nguyen)
6. Re: Cisco 3750 High CPU (Mack McBride)
7. Re: Cisco 3750 High CPU (David Prall)
--
Message: 1
Date: Wed, 7 Apr
Not sure what Adjust regions is. After a google search nothing turns up.
here is my cpu output:
sh proc cpu sorted | e 0.00
CPU utilization for five seconds: 72%/49%; one minute: 69%; five minutes:
69%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
56 1458890966
All,
I have a GSR 12008 with 2 GRP-B route processors. Running
gsr-k4p-mz.120-32.S11.bin
My GRP failed over about 45 minutes ago to the backup in Slot1 from Slot0.
I keep getting this in my logs.
SEC 0:00:00:06: %MBUS-6-FIA_CONFIG: Switch Cards 0x1F (bit mask); Primary
Clock CSC_1
SEC
Slot0 we think has a defective GRP, we removed and errors are gone. I have a
new GRP being shipped for tomorrow.
Thanks
On Tue, Jul 21, 2009 at 5:07 PM, Aaron dudep...@gmail.com wrote:
Looks like a fabric problem.
On Tue, Jul 21, 2009 at 14:34, Chris Lane clane1...@gmail.com wrote:
All,
I
-Original Message-
From: cisco-nsp-boun...@puck.nether.net [mailto:
cisco-nsp-boun...@puck.nether.net] On Behalf Of Chris Lane
Sent: venerdì 24 aprile 2009 1.09
To: Peter Rathlev
Cc: cisco-nsp@puck.nether.net
Subject: Re: [c-nsp] 3750 High Cpu IP Input
sh platform tcam utilization
CAM
% 0.13% 0 HQM Stack
Proces
1365414 595 9099 0.79% 0.71% 0.64% 0 PI MATM Aging
Pr
168 66256341597193 10.54% 9.76% 8.61% 0 IP Input
On Fri, Apr 24, 2009 at 2:31 AM, Peter Rathlev pe...@rathlev.dk wrote:
On Thu, 2009-04-23 at 19:09 -0400, Chris Lane
doc reads the HULC LED is a possible link flapping yet nothing in
logs indicate.*
*
*
On Fri, Apr 24, 2009 at 5:12 AM, Chris Lane clane1...@gmail.com wrote:
sh ip cef switching statistics feature
IPv4 CEF input features:
FeatureDropConsume Punt Punt2Host Gave
:
FeatureDropConsume Punt Punt2HostNew
i/f
Total0 0 0 0
0
On Fri, Apr 24, 2009 at 2:31 AM, Peter Rathlev pe...@rathlev.dk wrote:
On Thu, 2009-04-23 at 19:09 -0400, Chris Lane wrote:
sh platform tcam
into tcam
Brian
--
*From:* Chris Lane [mailto:clane1...@gmail.com]
*Sent:* venerdì 24 aprile 2009 11.17
*To:* Brian Turnbow
*Cc:* Peter Rathlev; cisco-nsp@puck.nether.net
*Subject:* Re: [c-nsp] 3750 High Cpu IP Input
sh controllers cpu-interface
ASIC
reverse
Drop due to input queue full: 0
Thanks for looking.
On Fri, Apr 24, 2009 at 7:45 AM, junior drr...@ya.ru wrote:
Hi,
Did You check TAC cases?
Can You post this switch current configuration with sh ip traffic command
output?
WBR
Roman A. Nozdrin
Chris Lane wrote:
1 routed
input
Regards
Chris
2009/4/24 Chris Lane clane1...@gmail.com
Yes with a high preference.
2009/4/24 junior drr...@ya.ru
Hello.
Does this switch have default route?
Chris Lane wrote:
sh ip traffic IP statistics:
Rcvd: 37788273 total, 24253 local destination
0 format errors, 0
, transport_start 0x0, caller_pc 0x6D1024
source: 74.212.165.187, destination: 224.0.0.252, id: 0x3CDA, ttl: 1,
TOS: 0 prot: 17, source port 58064, destination port 5355
These TTL=1 are causing the high CPU.
On 24 Apr 2009, at 14:26, Chris Lane wrote:
Richard Gallagher found
Having a high cpu with my 3750 not in stack. sh proc cpu | exclude 0.00
CPU utilization for five seconds: 68%/43%; one minute: 69%; five minutes:
70%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
16840336940 92166921437 15.49% 15.76% 15.97% 0 IP Input
.
On Thu, Apr 23, 2009 at 4:01 PM, Peter Rathlev pe...@rathlev.dk wrote:
On Thu, 2009-04-23 at 13:51 -0400, Chris Lane wrote:
Having a high cpu with my 3750 not in stack. sh proc cpu | exclude 0.00
CPU utilization for five seconds: 68%/43%; one minute: 69%; five minutes:
70%
PID Runtime
...@rathlev.dk wrote:
On Thu, 2009-04-23 at 16:15 -0400, Chris Lane wrote:
This box has been in production for over a year and doesn't really do
to much as you can see from my orig thread it moves about 11MB.
This just started late last night yet we didn't add any new customer
nor did
All,Please help me identify why my 3750ME is throwing these errors.
%SCHED-3-THRASHING: Process thrashing on watched message event. -Process=
SSH Process, ipl= 6, pid= 98
-Traceback= 2E4424 2E4B70 D0C404 D0C78C ED455C ED4FE8 ED5A44 ED657C ED6650
CBE0C8 CBE32C CBEA68 CBE914 29BD4C ED996C EDA25b
All,
GSR question, appears Cisco finally got around to updating the IOS train on
12.0.32.S – we have been running S8 for a while but S11 just came out and it
appears to have many new features! One of my routers is running 12.0.32.S6 –
its been so for 2years. I had a bad 8 port FastE lc a while
PROTECTED] wrote:
Hi,
Look for errors in show controller fia.
Maybe the LC was badly seated...
Maybe you have a bad SFC...
There are a lot of possibilities.
Cheers,
Leonardo Gama.
--
*De:* [EMAIL PROTECTED] em nome de Chris Lane
*Enviada:* qua 10/9/2008 15:58
and cooling is in order, ensure
airflow through the chasis hasn't been compromised by an uncovered linecard
slot for instance and a sh env all, sh diag and logs would help.
/eninja
On Tue, Mar 18, 2008 at 4:29 AM, Chris Lane [EMAIL PROTECTED] wrote:
I am getting error
%ENV_MON-2-FAN: Fan
I am getting error
%ENV_MON-2-FAN: Fan array has reached CRITICAL level.
I did a search and found this on Ciscos website.
%ENV_MON-2-FAN : Fan array has reached [chars] level.
ExplanationThere might be a hardware
Has anyone tried to use a 10/100/1000 base T copper based SFP and had a link
run MPLS at 100mbps?
I am trying to configure this in the ES ports and can get the port to go
UP/UP but cannot arp across the link.
The switch port is directly plugged into a GSR FastE port.
Thank you,
Chris Lane
We have built a lab with a Cisco GSR 12008 and 3 3750ME-24TE's.
I am running version 12.2(37)SE1 on all switches
GSR---SW1SW2---SW3
I cannot get the 3750 to enable MPLS on the FastEthernet port
SWITCH
interface FastEthernet1/0/1
no switchport
ip address x.x.x.x subnet
ip flow ingress
Anyone experience this CEF memory issue on a line card that is SHUTDOWN?
%SYS-2-CHUNKBOUNDS: Could not
59.544.5
4 59.045.5
6 56.543.0
7 53.042.5
Does anyone have a suggestion?
Thank
Chris Lane
--
//CL
___
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net
50 matches
Mail list logo