Hi folks
I want to configure my ASA for remote access via outside however it
configuration do not work, IP are fake for reasons security. My
configuration is
In the outside interface I have
interface Vlan2
nameif outside
security-level 1
ip address 200.10.45.98 255.255.255.240
telnet
There is a poll about matter.
http://gigaom.com/2009/03/18/why-cisco-not-ibm-should-buy-sun/
Regards
On Thu, Mar 19, 2009 at 12:45 PM, Paul asobihou...@yahoo.com wrote:
That's understood. Lelio said that he thought Cisco would fit well with
Sun.
- Original Message
From:
Hi,
Not sure what you are looking for, but you could use ossec, it is a hids.
http://www.ossec.net/
On Thu, Jan 22, 2009 at 3:51 AM, Dave Kruger
dave.kru...@za.verizonbusiness.com wrote:
also see hping:
http://www.hping.org/
hth
Dave
Andrew Gristina wrote:
netcat
If you have a unix or linux server you can use a cron, using expect or
perl to execute some command in your cisco router.
http://www.ibm.com/developerworks/forums/thread.jspa?threadID=6160tstart=105
Regards
On Tue, Jan 6, 2009 at 2:50 PM, Darryl Dunkin ddun...@netos.net wrote:
If you were
I suggest that you configure a proxy server for Internet Traffic, you can
use it as cache or accelerator, only if you want user surf to the outside
internet over that tunneled connection.
By this way, you can control what kind information is allowed when
they connect to corporate network.
On Mon,
You could forward PPTP protocol to router Cisco. What kind of router Cisco
do you have? What is IOS version?
On Sun, Jan 4, 2009 at 7:12 PM, Brett Looney br...@looney.id.au wrote:
I have a Cisco device that is behind a NAT router already and I am
wishing to make a tunnel to another router
Dear collegues,
I have a router Internet in a branch office Cisco 878 ( the router is owned
for our ISP), it is connected via G.HDSL interface ( it is a Ethernet
Interface).
We have bought a router Cisco 1841 (2 Ethernet Interfaces). I want to know
if is possible reemplace router cisco 878 for our
Hi Pablo,
I think you should execute these commands in routed ports of cisco 1841.
router(config)#bridge 1 protocol ieee
router(config)#bridge irb
router(config)#int fa0/0
router(config-if)#bridge-group 1
router(config-if)#exit router(config)#int fa0/1
router(config-if)#bridge-group 1
Hi list,
Is there some way that I can configure my router to sent alerts to syslog
server or send alerts to a email when bandwitdh utilization is more
80% percent in WAN. Currently, I am trying to configure RMON with examples
Cisco IOS Cookbook, I have configured a cisco 871 to sent alerts to
Hi guys,
I have configured a Cisco ASA 5505 with two LAN's one for inside (servers)
and other for business (users), I can do a ping from business to inside
and viceversa hosts, I can authenticate me in the domani MS only when I
connect a PC in ports of ASA with access vlan 3, however when I
it. Try hard setting your port speed/duplex on the ASA
and switch. GL
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Jorge
Evangelista
Sent: Thursday, March 06, 2008 7:03 AM
To: cisco-nsp@puck.nether.net
Subject: [c-nsp] ASA help configuration
mtr
arping
pathload
pathrate
On Jan 28, 2008 4:12 PM, Garry [EMAIL PROTECTED] wrote:
Joseph Jackson wrote:
Hey all,
Myself and a coworker are trying to get together a list of the top ten
tools
any network engineer shouldn't be without. We're looking for vendor
neutral
tools. So
I had had similar issues with other routers Cisco Soho91, when I set
interface wan to work to a 10Full Duplex force, it could not see in
the configuration, I solve it upgrading my IOS, maybe you have to do it.
2008/1/17 Hiromasa Sekiguchi [EMAIL PROTECTED]:
Hi,
The below command didn't
Hi list,
I have enabled routing in my corporate switch, I had configured a
cisco 2800 from my ISP doing intervlan and I have moved VLANs of
corporation to my switch 3COM 5550G, but actually I have had some
issues putting ACLs, I have got block only traffic for VLAN 40, it
works fine, but for
http://www.blindhog.net/cisco-dual-internet-connections-without-bgp/
On 8/17/07, Tom Storey [EMAIL PROTECTED] wrote:
It can be done, but you must use route-maps in your ip nat inside source
statements instead.
The following configuration uses object tracking to fail over to a backup
link.
I think that you should reduce normal and extended burst, for example
I usually configure these way and it works fine, if I want to limit
64Kbps (for upload download) to 192.168.1.20
Normal Burst = configured rate * (1 byte)/(8 bits) * 1.5 seconds
Extended Burst = 2 * normal burst
Normal
Hi,
Is there anyway for deploy a VPN in mode bridge with Cisco 851 or
other models?, I want to deploy a VPN where I want have some hosts
inside the same subnet of main office, I have read that it is possible
with OpenVPN and Linux (http://www.linux.com/articles/58336). I do
not want to use NAT
Try to make a access-list beetwen your host and the server, then see
logs with the command debug ip packet ACL detail
You can use other commands for tracking the issue as debug packet
debug access-list
http://www.cisco.com/en/US/docs/security/fwsm/fwsm22/command/reference/df.pdf
On 7/24/07,
You can use cacti for monitoring traffic, there are addons that you
can put in it for alarms and netflow.
Trouble ticket express or Otrs for system tickets.
On 7/8/07, Paul Stewart [EMAIL PROTECTED] wrote:
Solarwinds - ran trial of it, didn't impress me much...
Netsaint, Nagios, Big Brother
Juniper Networks sells a boxes called WAN Acceleration
http://www.juniper.net/products_and_services/application_acceleration/wan_acceleration/wxc_application_acceleration/
http://searchnetworking.techtarget.com/originalContent/0,289142,sid7_gci1225932,00.html
On 5/26/07, Jason Plank [EMAIL
20 matches
Mail list logo