I've learned to always specify the full path to the image you want to
load. It's safer than assuming that rommon will find the image on its
own on the assortment of drives that the newer, larger devices have
these days.
Justin
Paul Zugnoni wrote:
fwiw, (nearly 2 months later) on our 4948:
"
fwiw, (nearly 2 months later) on our 4948:
"boot system flash cat4500-ipbasek9-mz.122-31.SGA8.bin" with a
config-register of 0x2102 resulted in the switch booting into rommon mode,
with an error message on the console that the device was not specified.
Upon removing that configuration statement an
Antonio Soares wrote:
Since you don't have a "boot system flash" statement in your config, you need a
config-register = 0x2101. This way it will load the
first available image in the bootflash.
Regards,
Antonio Soares, CCIE #18473 (R&S)
amsoa...@netcabo.pt
Just recently we had an iss
09 4:00 PM
> To: Antonio Soares; cisco-nsp@puck.nether.net
> Subject: Re: [c-nsp] need help about switch cisco 4 9 4 8
>
> Thank you
>
> Now I change it to 0x2102
> but it can't boot properly
>
> Can you help?
>
> Thank you
>
> The
K [mailto:chloekcy2...@yahoo.ca]
Sent: sexta-feira, 20 de Fevereiro de 2009 21:00
To: Antonio Soares; cisco-nsp@puck.nether.net
Subject: RE: [c-nsp] need help about switch cisco 4 9 4 8
Thank you
Now I change it to 0x2102
but it can't boot properly
Can you help?
Thank you
The
8473 (R&S)
amsoa...@netcabo.pt
-Original Message-
From: cisco-nsp-boun...@puck.nether.net
[mailto:cisco-nsp-boun...@puck.nether.net] On Behalf Of chloe K
Sent: sexta-feira, 20 de Fevereiro de 2009 19:08
To: cisco-nsp@puck.nether.net
Subject: [c-nsp] need help about switch cisco 4 9 4 8
@puck.nether.net
Subject: [c-nsp] need help about switch cisco 4 9 4 8
Hi
I have problems in this switch 49 48
1/ I can't setup the management interface.
I have another same modeul. I can see there is Fasthernet to set it up as
management port.
2/ After reload, I lost
Hi Rich
Thank you so much for your fast response.
for the 1st quesiton, what is "config-register = 0x1"?
for the 2nd question, I have same model switch
there is int "FastEthernet1" to let me to configure the management int
interface FastEthernet1
no ip address
speed au
ewbhuff | Fax: 914-460-4139
-Original Message- From: cisco-nsp-boun...@puck.nether.net
[mailto:cisco-nsp- boun...@puck.nether.net] On Behalf Of chloe K Sent:
Friday, February 20, 2009 2:08 PM To: cisco-nsp@puck.nether.net Subject:
[c-nsp] need help about switch c
chloe K wrote:
> Hi
>
> I have problems in this switch 49 48
>
> 1/ I can't setup the management interface.
> I have another same modeul. I can see there is Fasthernet to set it up as
> management port.
>
> 2/ After reload, I lost configuration. I did copy run start
> It sai
ruary 20, 2009 2:08 PM
To: cisco-nsp@puck.nether.net
Subject: [c-nsp] need help about switch cisco 4 9 4 8
Hi
I have problems in this switch 49 48
1/ I can't setup the management interface.
I have another same modeul. I can see there is Fasthernet to set it
up as management port.
2/ Afte
| Phone: 914-460-4039
aim: matthewbhuff | Fax: 914-460-4139
> -Original Message-
> From: cisco-nsp-boun...@puck.nether.net [mailto:cisco-nsp-
> boun...@puck.nether.net] On Behalf Of chloe K
> Sent: Friday, February 20, 2009 2:08 PM
> To: cisco-nsp@puck.nether.net
> Subjec
Hi
I have problems in this switch 49 48
1/ I can't setup the management interface.
I have another same modeul. I can see there is Fasthernet to set it up as
management port.
2/ After reload, I lost configuration. I did copy run start
It said that it can't find the Valid boot
13 matches
Mail list logo
