Hello all:
I recently attempted to upgrade from 2.1 to potato and observed the
following:
When using deselect for upgrade purposes the symbolic link between
/bin/bash and /bin/sh was removed following the upgrade of bash.
Following the loss of this sym-link all upgrade attempts failed with
the
Hello all:
For the past couple of days I have been trying to install potato on a
system. I have encountered problems. The problem is with libc6.
I have tried to remove, -force-remove etc with dpkg without success.
I am running 2.2.12 on this PC.
Following is the command I have issued and the
Hello Neil:
via the card configuration tool from the manufacturer,
you should be able to change the IRQ and I/O mapping
for the card(s) in question.
Peter
Neil Booth wrote:
I have 2 PCI Planex ethernet cards in my machine, the first uses
tulip.c as its driver, and the second uses de4x5.c.
Hello:
What I find amazing about M$95/98 is that if you turn off
the screen saver, many problems disappear.
Peter
[EMAIL PROTECTED] wrote:
I have already sent this message to the list but I don't know
if it has arrived because of problems with my subscription
address, so I resend it:
I
Hello:
edit /etc/hosts.deny and comment out the PARANOID line.
Bounce your portmap deamon or reboot your system and it should work.
Peter
Mahendra D. Khandkar SBO wrote:
Respected Sir,
I have installed Debian Linux 2.0 on a Pentium 90 Mhz machine.
I am trying to
Hello all:
Does anyone know if the SMC Ether EZ 10/100 NIC is support
in Linux.
Peter
begin:vcard
n:Iannarelli;Peter
tel;fax:1+ 416 929 1056
tel;work:1+ 416 929 1885
x-mozilla-html:FALSE
url:http://www.GenXl.com
org:GenX Internet Labs.;Operations
adr:;;238a Gerrard St. East
Hello:
I use the exact same card and it works fine.
Make sure you don't have any interupt conflicts.
Peter
Fredrik Jonsson wrote:
Hi,
According to the Hardware-HOWTO Linux should support the 3Com 509B
Ethernet card. When I try to install the driver I get an error and during
booting a
Hello all:
NIC card question .
Does anyone know if the D-link DFE-530TX NIC
is supported ?
Peter
begin:vcard
n:Iannarelli;Peter
tel;fax:1+ 416 929 1056
tel;work:1+ 416 929 1885
x-mozilla-html:FALSE
url:http://www.GenXl.com
org:GenX Internet Labs.;Operations
adr:;;238a Gerrard St. East
This message is associated with the physical card and
the settings the card will try to run in graphics mode.
Check you card to make certain you are selecting the
proper manufacturer and model and check the frequency
(Horz and Vert) capabilities of your monitor.
Run xf86config once you have all
Hello:
I running potato with a 2.2.10 SMP kernel.
I boot my system klogd used 99% of the CPU
as reported by top.
What could I be doing wrong ? ( thats loaded )
Peter
begin:vcard
n:Iannarelli;Peter
tel;fax:1+ 416 929 1056
tel;work:1+ 416 929 1885
x-mozilla-html:FALSE
url:http://www.GenXl.com
Then explain why xosview version 1.7.1 on potato
reports the activity of both CPUs.
Sean 'Shaleh' Perry wrote:
On 24-Jun-99 Marcus Johansson wrote:
Hi!
We have a HP-UX box with dual cpu's, and the 'top' program shows the status
of
both cpu's, and even which cpu the processes are
Nico:
uucp package for cu.
Peter
Nico De Ranter wrote:
Howdy,
I need to talk to my serial port. On other Unices I would
use tip or cu. Any idea which package contains these tools?
(I know they both exist for Linux since I used them before,
unfortunately I reinstalled Debian and I
Hello:
Assuming all your users are using bash,
put your global environmental setting in
/etc/profile
Peter
Marco Maggesi wrote:
I am looking for the appropriate place where to put some
basic environmental definition like:
PAGER=less
so that they take effect to every user (unless
Hello all:
Does anyone know if Debian GNU/Linux support
an SMC 1211TX NIC. ( any kernel version )
Peter
begin:vcard
n:Iannarelli;Peter
tel;fax:1+ 416 929 1056
tel;work:1+ 416 929 1885
x-mozilla-html:FALSE
url:http://www.GenXl.com
org:GenX Internet Labs
adr:;;238a Gerrard St.
Hello all:
Quick question about preventing http downloads.
Using the ipchain linux firewall facility I can see how to stop allowing
nodes on a LAN to download files via ftp. My question is using that
same firewall how does one stop these nodes from downloading
files via http?
Thanks in
Hello Matthew:
To change the IP address, network, etc of you NIC
to into /etc/init.d/network.
You will see everything you need there.
Peter
Matthew Wade Roberts wrote:
When I first installed Debian, I entered incorrect information
for the IP addresses of the network. I need to correct
Check out http://metalab.unc.edu/LDP/ . There is lots of information
there.
Peter
José L. Redrejo - ITAIS wrote:
HI, I'm a linux beginner who comes from de world of Windows NT and I'm
getting a little crazy.I have installed liinux without many problems,
KDE and apache and I am working with
Hi Chris:
You might try shutting off auth in /etc/ppp/peers/?
Change it to noauth.
Peter
Chris Kaltwasser wrote:
Hi all -
Hopefully someone here in Debian-user land is familiar enough with pppd to
give me some help with this. I'm trying to get a dialup PPP connection set
up between
Hello all:
Does anyone know if there is a way to pull the
password used to connect/logon to a samba share ?
I know that the user ID can be acquired via %U.
Peter
begin:vcard
n:Iannarelli;Peter
tel;fax:1+ 416 929 1056
tel;work:1+ 416 929 1885
x-mozilla-html:FALSE
url:http://www.GenXl.com
Jor-el:
Why not try creating separate PPP setups under separate shell accounts.
Peter
Jor-el wrote:
Hi,
It seems to me that the current PPP initiation scripts do not
allow one to maintain multiple accounts at one ISP for different users on
the same dial-out machine. The only way
Hello Ken:
Go into /etc/ppp/options. At the bottom of the file
IPX is shut off, simply turn it on.
Peter
Ken McCord wrote:
Does anyone know if IPX support was compiled into slink's PPP? If not,
where do I need to modify the source to add support?
Thanks,
Ken
--
Unsubscribe? mail -s
Hi Chris:
ATM0
Chris Hoover wrote:
Does anyone know the command to tell a modem to turn the sound off?
Also, is there a page somewhere that lists the hayes/at modem commands?
I've been looking for one, but no luck so far.
Thanks,
Chris
--
Unsubscribe? mail -s unsubscribe [EMAIL
Hell William:
I think the offending package is xbanner.
I'm assuming you have installed xdm. SO
/etc/X11/xdm/Xsetup_0 holds the offending line.
ie.
# XBanner - begin
/usr/X11R6/bin/freetemp
/usr/X11R6/bin/xbanner -file /etc/X11/XBanner.ad
# XBanner - end
Just comment it out.
Peter
Hello Tom:
Sounds like your DNS is not setup correctly.
install the bind package and run bindconfig.
Peter
Tom Perkins wrote:
I recently loaded Linux onto my PC (Pentium II) and configured PPP
correctly. I am able to connect to my ISP successfully, but I cannot reach
any ftp site (e.g.
Hello all:
Does anyone know how to prevent one from
CDing out of there home directory from within FTP.
Or can someone tell me where I can read up
about this.
Peter
it this way
userid * 205.208.9.10
Assuming yodeller is the node name, the way you have indicated
above should work. I've tried in on my server as well but it doesn't
seem to work.
Peter Iannarelli
BEGIN:VCARD
N:Iannarelli;Peter
FN:Peter Iannarelli
EMAIL;PREF;INTERNET:[EMAIL PROTECTED
Hello Nigel:
Look in /etc/init.d/network. In there you will see a series
of variable definitions and network commands. Create the
same setup (in that file with different numbers) for your
second NIC.
Then reboot, and away you go
Peter
[EMAIL PROTECTED] wrote:
Thanks for reading this
Hello Daniel:
Joseph Hartmann wrote:
1) I chose 'access method CD-ROM' and it properly found the 'main'
and
'contrib' packages and binaries. Where do I find the 'local'
packages? It
says, this directory is named 'local/binary' on the distribution
site.
Hi Guys:
This is what I do.
I don't log in. Loging in implies V.120. V.120 sucks.
When I get the CONNECT is just start ppp negotiation.
This approach seem to work with several ISPs.
I'm using a Zyxel ISDN modem at 128 so don't be
confused with the init or dialing strings.
Below is my provider
Hello Dennis:
I believe you are mistaken about crontab -e. I use it all the time.
Firstly make sure the cron or anacron package is installed.
The documentation is in /usr/doc. There is also a HOWTO
directory you may want to check out.
Peter
[EMAIL PROTECTED] wrote:
I am slowly moving from
Hello:
This is certainly possible. Your ISP may give you more than 8 IPs depending
upon his/her current block assignment schema.
You will need the following information.
Network interaface address
Broadcast address
Netmask
If possible as your ISP to provide a group of addresses outside of the
Hello Bostjan:
Goto
ftp://ftp.debian.org/debian/dists/stable/main/disks-i386/current/install.html
and it is all explained there.
Peter
Bostjan JERKO wrote:
Hello !
Can anybody tell me how to create basic diskettes for Linux (e.g. Debian) to
install on PC without CD-ROM and than install
Hay there absolute beginner:
That pretty good for a first go around.
To uncompress the .gz files. Use gunzip file-name.
Happy uncompressing.
Peter
Alain Cadenat wrote:
Hy all,
I am an absolute beginner in linux and Debian
I have just download and (successfully) installed the base
hello Rodrigo:
I've never seen problems with a floppy before. Thats a good one.
Try booting a DOS floppy if you can to see what happens.
Try resetting the CMOS to the manufacturers defaults. You may also
try removing the two hard drives on your second IDE chain for the install.
You can
Hay all:
I think md is for the ramdisk.
how much memory is available ?
Peter
Andreas Loosen wrote:
Hi, Peter,
It doesn't seen to be a floppy problem but the md-driver seems to hang.
Ciao
Andreas Loosen
-Original Message-
From: Peter Iannarelli [mailto:[EMAIL PROTECTED
Rodrigo
You certainly have lots of RAM.
Disconnect the two HDs on the 2nd IDE chain and try again.
Check the manufacturers WEB site for firmware updates.
Peter
Rodrigo Moya wrote:
I think md is for the ramdisk.
how much memory is available ?
I've got 64MB of memory
Thanks
begin:vcard
Hello:
Wouldn't it just be cleaner to use dial on demand (diald)
which would automatically bring up and/or turn down the
link based on idle time.
Peter
-Original Message-
From: Moore, Paul [EMAIL PROTECTED]
To: 'Debian Users' debian-user@lists.debian.org
Date: Wednesday, October 21,
Hello:
You can turn off the portmapper vi /etc/init.d/xinetd stop or
/etc/init.d/inetd stop. This however is not recommend because
any requests comming in on ports will not be serviced. Note.
portmaps are used to save system resources. It starts up
listening daemons on an as required basis as
of listening daemons ( ie, in.telnetd ),
as opposed to running in.telnetd as a deamon.
Peter
Miquel van Smoorenburg wrote:
In article [EMAIL PROTECTED],
Peter Iannarelli [EMAIL PROTECTED] wrote:
You can turn off the portmapper vi /etc/init.d/xinetd stop or
/etc/init.d/inetd stop. This however
Hello Nuno:
It looks like the system wasn't shutdown properly.
However your disk may have got itself a bad block.
Try running /sbin/badblock and see what happens.
Peter
-Original Message-
From: Nuno Carvalho [EMAIL PROTECTED]
To: debian-user@lists.debian.org
help.
--
Unsubscribe? mail -s unsubscribe [EMAIL PROTECTED] /dev/null
begin: vcard
fn: Peter Iannarelli
n: Iannarelli;Peter
org:GenX Internet Laboratories Inc.
adr:20 Madison Ave.;;;Toronto;Ontario;M5R 2S1;Canada
email;internet: [EMAIL
\ /
/\__/ Paul Crowley Nov 8 http://www.hedonism.demon.co.uk/permission /~\
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
begin: vcard
fn: Peter Iannarelli
n: Iannarelli;Peter
org:GenX
]
--
Unsubscribe? mail -s unsubscribe [EMAIL PROTECTED]
/dev/null
begin: vcard
fn: Peter Iannarelli
n: Iannarelli;Peter
org:GenX Internet Laboratories Inc.
adr:20 Madison Ave.;;;Toronto;Ontario;M5R 2S1;Canada
email;internet: [EMAIL PROTECTED
: Peter Iannarelli
n: Iannarelli;Peter
org:GenX Internet Laboratories Inc.
adr:20 Madison Ave.;;;Toronto;Ontario;M5R 2S1;Canada
email;internet: [EMAIL PROTECTED]
title: Engineer
tel;work: 1+ 416 929 1885
tel;fax:1+ 416 929 1056
on which we're of course working?
--
Alex Shnitman
[EMAIL PROTECTED], [EMAIL PROTECTED]
http://alexsh.home.ml.org
--
Unsubscribe? mail -s unsubscribe [EMAIL PROTECTED] /dev/null
begin: vcard
fn: Peter Iannarelli
n: Iannarelli;Peter
org:GenX
Hello j?rg:
I believe #27 or 28 in xf86config should meet your requirements.
Peter
-Original Message-
From: j?rg bode [EMAIL PROTECTED]
Newsgroups: muc.lists.debian.user
To: [EMAIL PROTECTED]
[EMAIL PROTECTED]
Date: Friday, October 09, 1998 7:24 AM
Subject: X11: HELP for ATI 3DChar 4MB
Hello Jens:
Yes -- see xntp3
Peter
-Original Message-
From: Jens Lisner [EMAIL PROTECTED]
To: Debian-User-List debian-user@lists.debian.org
Date: Thursday, October 08, 1998 7:48 AM
Subject: Timeserver?
Hi all!
My provider gave me a timeserver adress. What can I do with it under
Hello Anthony:
There is a file in /usr/sbin call update-rc.d. It permitts
the addition and removal of startup files from the respective
run-level directories.
Peter
-Original Message-
From: Anthony Campbell [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Hello Zheng
What does the dmesg command say? Did it see the card and
load the driver at boot time?
If so, what does ifconfig say?
Peter
-Original Message-
From: Zheng Wang [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Wednesday, October 07, 1998
Try running bindconfig instead.
Peter
-Original Message-
From: Anthony Landreneau [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Wednesday, October 07, 1998 12:25 PM
Subject: named-bootconf failure
Greetings,
named-bootconf is no longer working
Hi:
To my knowledge there is no way to recover the root.
You could however try to re-activate that partition and
see what happens. I doubt it will work because mkfs
resets the inode tables.
When you re-activate/create that partition again everything
on it is reset. So, you have to re-install the
Hello:
In my pap-secrets I have the following
# INBOUND connections
# Every regular user can use PPP and has to use passwords from /etc/passwd
#* moose *
* * *
Peter
-Original Message-
From: Eugene Sevinian [EMAIL PROTECTED]
To:
Hi all:
Does anyone know of any EDI software which
runs under Debian or Linux.
Thanks
Peter
Hi Shao:
Sounds like a DNS issue. When you pinged did you use an
IP address or a fully qualified host.domain.name ?
Check or run bindconfig.
Peter
-Original Message-
From: Shao Ying Zhang [EMAIL PROTECTED]
To: question debian-user@lists.debian.org
Date: Thursday, September 24, 1998
Hello:
My personal preference is Zyxel -- www.zyxel.com
Peter
-Original Message-
From: G. Kapetanios [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Tuesday, September 22, 1998 9:46 AM
Subject: Modem recommendation
Hi all,
I am switching from
Hello Mohan:
I don't know if this is going to work but you can try it.
In your /etc/ppp/options file put a line as follows:
# Set the assumed name of the remote system for authentication purposes
# to n.
#remotename n
name login-name
That is the name to send to login.
In your
-Original Message-
From: Kent West [EMAIL PROTECTED]
To: Kenneth Scharf [EMAIL PROTECTED]
Cc: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Thursday, September 17, 1998 2:28 PM
Subject: Re: How to start PPP?
At 10:03 AM 9/17/1998 -0700, you wrote:
I've been reading the
Hello Hubert:
If you need this driver to run X, starting at card number 227 in the
xf86config program are the Matrox cards.
Peter
-Original Message-
From: Hubert [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Tuesday, September 15, 1998 6:09 AM
Hello Micki:
Are you sure its your card?
Did you run xf86config ?
Look in /var/log/xdm-errors to see what the error message(s) is.
Peter
-Original Message-
From: Micki Heyns [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Monday, September 14, 1998
Hello:
You have enough space.
My recommendation would be to setup a 32 megabyte swap
partition and use the rest for linux and the packages.
Peter
-Original Message-
From: W.N. Beukers [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Friday,
[EMAIL PROTECTED]
To: Peter Iannarelli [EMAIL PROTECTED]
Cc: W.N. Beukers [EMAIL PROTECTED]; debian-user@lists.debian.org
debian-user@lists.debian.org; recipient list not shown: recipient list
not shown:
Date: Friday, September 11, 1998 7:17 AM
Subject: Re: linux
My recommendation would
Hello Gene:
I had the same problem. If you are using smail, in the /etc/smail/config
you can adjust the authentication for a specific IP addresses or subnets.
Thus your server receive e-mail from the location in question.
The line in question is smtp_hello_broken_allow
Peter
-Original
Hello Rick
Provide a trace of a dialin attempt and I'm certain
someone can tell you what is wrong.
Peter
-Original Message-
From: Rick Smith [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Saturday, September 05, 1998 7:27 AM
Subject: PPPD
Hi
I
hello Kenneth:
You have to mount your partition after you create a file system
mkfs [device] - to make a file system before you can
mount it.
Then run df.
Peter
-Original Message-
From: Kenneth Scharf [EMAIL PROTECTED]
To: [EMAIL PROTECTED] [EMAIL PROTECTED]
Cc:
Hello Cristov:
You should be running dselect from the root account.
If you are ignore the above sentence. I personally have
to run dselect several times when performing a raw
install. This is because some of the dependencies must
be satistied before other packages can be installed ( I think ).
Hello Remo:
Within the /etc/init.d/network file your network route command
should be specified ( for your network ). Check this file
to make certain that the route arguments are correct.
Every time you boot your system, the ifconfig and route
directives will be issued based on the contents of
Hello:
Install smail and qpopper. Answer the questions during install.
NOTE - your name server must be setup properly before you
can use SMTP and you should have a fully qualified domain name.
Peter
-Original Message-
From: htyj [EMAIL PROTECTED]
To: debian-user@lists.debian.org
Picked up some reading material for a flight to New Brunswick. Found a
great article on Linux. This really demonstrates the power of knowledge
sharing. Should have been a case study at the big knowledge management
summit in San Diego earlier this year.
Hello:
You say your running X, what is your window manager?
Select 1, fvwm, fvwm95, KDE, also install kdm or xdm.
Peter
-Original Message-
From: Hersh, Harry [EMAIL PROTECTED]
To: 'Rafael Cordones Marcos' [EMAIL PROTECTED]
Cc: Debian Users debian-user@lists.debian.org
Date: Friday,
-Original Message-From:
Peter Iannarelli [EMAIL PROTECTED]To: Debian ISP
debian-isp@lists.debian.orgDate:
Friday, August 21, 1998 6:39 PMSubject: PPP and wtmp not working
together
Hello:
I read today that in 2.0, a ppp account is not
getting logged
into the wtmp file. I decided
Hello:
I have a 90 MHz Compaq with 32 megs of memory.
Its running 1.3.1. For some reason Linux only sees
16 megs of memory. Does anyone know why and
how I can fix this ?
Peter
BEGIN:VCARD
VERSION:2.1
N:Iannarelli;Peter
FN:Peter Iannarelli
ORG:GenX Internet Laboratories
TITLE:Engineer
Hi Franz:
Send a trace of the PPP negotiation (via the debug option)
and we can tell you why.
Peter
-Original Message-
From: Franz [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Sunday, August 16, 1998 6:23 AM
Subject: pppd
Hi !
Does anyone
Hello Paul:
I use the edquota command. Its pretty easy to use just read the man page.
You should note that quota must be turned on in the kernel and the target
file system must be mounted with quotas on -- i.e. in /etc/fstab
# /etc/fstab: static file system information.
#
# file system
Hello Luiken:
Vesa and X have nothing to do with each other.
If you have a vesa graphics card, I'm sure the appropriate
drive will take full advantage of it.
If you have a Vesa bus on your PC just make certain
that the card you have is defined in the xf86config setup
program. i.e. - ATI MACH 32
Hello Arijan:
If you are currently using ttyS0 for you mouse that is probably
because you to do not have a PS/2 mouse interface. Therefore
creating a mouse device would not be practical. However
if you want a /dev/mouse device simply create a symbolic
link to ttyS0 via the command ln -s
Hello Paul:
Yes there is -- I think.
-Original Message-
From: Paul Miller [EMAIL PROTECTED]
To: Debian User debian-user@lists.debian.org
Date: Wednesday, August 05, 1998 6:20 AM
Subject: user limits
Is there any way to limit background processes?
Check out the ulimit command. More
Hello Cesar:
Your are not wrong.
Peter
-Original Message-
From: Cesar Talon [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Monday, July 27, 1998 5:34 AM
Subject: Mounting Win95 Shares with samba
Hello,
I would like to mount (if possible) a win95
Hello Art:
stdio is in /usr/include however; the compiler, by default
should be looking there via #definestdio.h. Therefore
if this is not happening, you may want to re-install your gcc.
Peter
-Original Message-
From: Art Lemasters [EMAIL PROTECTED]
To: debian-user@lists.debian.org
Hello
all:
Does
anyone know if there is a way to reset a users usage
(login time) in the wtmp file to zero ?
Thanks
in advance
Peter
BEGIN:VCARD
VERSION:2.1
N:Iannarelli;Peter
FN:Peter Iannarelli
ORG:GenX Internet Laboratories Inc.;Engineering
TITLE:Senior Engineer
Hi Phil:
Someone correct me if I'w wrong.
I believe you have to run dselect to install
the rest of the packages that autoup.sh removed
Peter
-Original Message-
From: Phil Dyer [mailto:[EMAIL PROTECTED]
Sent: June 29, 1998 7:48 AM
To: debian-user@lists.debian.org
Subject: hamm
Hi Stef:
In debian it not in.pop3 but in.qpopper.
Peter
-Original Message-
From: Stef Hoesli Wiederwald [mailto:[EMAIL PROTECTED]
Sent: June 28, 1998 9:59 PM
To: debian-user@lists.debian.org
Subject: How to enable pop3?
How can I enable pop3 support in Debian 1.3.1?
I added a line
Hello:
If you are using the bash shell you
can use the ~/.bash_logout file to execute
some commands. In that file you could put a
tput clear to clear your screen.
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
Sent: June 29, 1998 10:42 AM
To:
Hello
all:
Have to
go to Dublin Ireland for a couple of weeks.
Need
internet access while I'm there.
Does
anyone (developer or user) who uses Debian
know of any ISPs in Dublin? Preferable one
who
uses Debian.
Thanks
in advance.
Peter
BEGIN:VCARD
VERSION:2.1
N:Iannarelli;Peter
Hello all:
Yesterday I tried to get the 2.1.108 kernel up and running.
I did get it running however I hand one problem, may ethernet
card (3Com 3C905 vortex) stopped. I am currently running
Debian's latest released kernel 2.0.34 and all is find.
With the 2.1.108 kernel, ifconfig reports the NIC
Hello:
To the best of my knowledge there is no reason why the
3C509 card would not work. You will probably have to
do a kernel rebuild. I suggest you down load the 2.0.34
sources however.
Peter
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
Sent: July 5, 1998
Hello Gerald:
There is a package called samba. It is from what I
understand equivalent to NT. You can share printers,
CDROMs, directories etc.
Peter
-Original Message-
From: Gerald V. Livingston lI [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date:
Hello all:
-Original Message-
From: Patrick Ouellette [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: May 12, 1998 9:00 AM
Subject: XDM doesn't work
Hello all,
I have had the following problem no 2 different hamm systems:
They are configured to
The creative juices that flow while under the influence always
look really bad the next day. :-)
You are interested in the following:
/etc/ppp --- directory
/etc/ppp.chatscript
/etc/ppp.options_out
Also; if in your state you thought it would be a good time to
recompile your kernel, make sure
Hay James:
When performing a raw install of
Debian,
it will install all necessary
packages
automatically. Form that point
forward
it is up to you what other packages to
install. The packages you select
would
obviously depend upon the
functionality
you desire.
Peter
-Original
Hello all:
Can some point me in the direction or tell me where I can
learn about a poppassd client for linux/unix, Mac and wincrash95.
Thanks in advance
Peter
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Hello Gordon
Try using the letter q. q for quit.
Peter
-Original Message-
From: Gordon von Miller [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Sunday, April 19, 1998 9:34 AM
Subject: [EMAIL PROTECTED]
Debian disk and keyboard echo
Hello,
I
Hello:
Sounds like your dns or default route is not setup properly.
Make sure your default route is the NIC to your ISP and
run bindconfig.
Peter
-Original Message-
From: Atte Koivula [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Sunday, April
Hello all:
This past weekend I did a raw install of hamm.
I have a few problems but I got it running and fairly stabilized.
Because I am The master of disaster I thought I would
fiddle around with the lilo.conf. I changed it such that
it now contains append=mem=64m, then ran lilo.
Now when it
Hay Wolf:
What I would do in this case is remove the hardware that
you don't need to perform an install.
It could be an interrupt problem, or something like that.
Once the system is up and running, you can put the
hardware back in. Just get ride of the sound card and
modem. Also; Make sure your
screwed up my system
On Tue, Mar 24, 1998 at 04:13:40AM -0500, Peter Iannarelli wrote:
[lilo messed up]
Can someone tell me how I can restore the old lilo/boot or
do I have to do a complete re-install of hamm again ?
NOTE: I only have the debian rescue floppy to boot from.
Use the rescue
Hi Michael:
To achieve the look that you want, in your .bash_profile
enter the following:
NODENAME=`tput smso``tput blink`[`hostname`]`tput sgr0`
PS1='${NODENAME}${PWD}'
PS2='${PWD}'
Peter
-Original Message-
From: Michael Agbaglo [EMAIL PROTECTED]
To: debian-user@lists.debian.org
Hello all:
Can anyone tell me how to properly create
a link from the anonymous ftp/pub directory
to another directory located on the same or
on a different file system.
thanks in advance.
Peter
--
TO UNSUBSCRIBE FROM THIS MAILING LIST: e-mail the word unsubscribe to
[EMAIL PROTECTED] .
Hi Bob:
You have to install the print spool software. Use deselect.
Since you are a beginner, install the simple lpr package.
Peter
-Original Message-
From: [EMAIL PROTECTED] [EMAIL PROTECTED]
To: debian-user@lists.debian.org debian-user@lists.debian.org
Date: Thursday, January 29,
-//-GtiMan-//- wrote:
hello,
I have a ATI Rage 3D and i haven't the drivers for this graphic card to
configure Xfrr86...
Within the xf86config program line number 24 is the 3D RAGE
Peter
--
TO UNSUBSCRIBE FROM THIS MAILING LIST: e-mail the word unsubscribe to
[EMAIL PROTECTED] .
Hello Oliver:
Try looking at the mt command. It provides facilities for
manipulating a tape drive.
I have in the past had to use the mt setblk 0 command
to read tapes from Alphas and HPs.
Hope this will help.
Peter
-Original Message-
From: Oliver Elphick olly@lfix.co.uk
To:
1 - 100 of 171 matches
Mail list logo