>
> Hi There:
>
> I’m in need of a 120/240 slide switch used on the AC-4 power supply.
> If anyone out there has one please let me know. Email my QRZ address.
> Thanks very much. Gary W9VS
___
Drakelist mailing list
Drakelist@zerobeat.net
Hello again to the list:
I want to buy a 9.6MHZ crystal used in the
FS-4 synthesizer. If you have one and
want to sell it please let me know.
Email me at my QRZ email address.
Thanks very much. Gary Thostenson W9VS
---
This email has been checked for viruses by Avast antivirus software.
My T-4XC tunes up normally in the tune mode. When I switch to CW and key down I
get full output no matter where the gain control is set. The only way I can
reduce output is to detune the RF tune control.
John Meyer K8IHY
Hi All...I could use a good condition tuning dial for a R4, R4-A or R4-B.
Mine is terrible.
Thanks,
73,
Lee
-Original Message-
From: Evan Rolek k9...@aol.com
To: 1oldlens1 1oldle...@ix.netcom.com; drakelist drakelist@zerobeat.net
Sent: Mon, Dec 16, 2013 6:27 pm
Subject: Re:
well I had a bad night.
I got this broke W4 from ebay. the pickup sensor was messed up. got that fixed.
Set the calibration trimmers and the thing worked like a charm.
except
I couldn't set the needle to zero. the setting screw moved the needle, but not
to zero. So I decided to fix it.
Greetings to the list:
I am looking for a replacement antenna switch for an MN-2000 Tuner. I recently
acquired this tuner, but it looks like in it's former life someone smoked the
antenna switch. From the looks of it, it appears to haver been hotswitched.
The ceramic portion of the
Have a ac-4 with a open primary winding,any suggestions?
anyone have a spare transformer they care to sell?
thanks
dale wt4t
___
Drakelist mailing list
Drakelist@zerobeat.net
http://mailman.zerobeat.net/mailman/listinfo/drakelist
Looking for a Drake ac-3 or Ac-4 supply. Does not have to be
working ,as long as the supply transformer is operational. Cosmetics not
important. cnn do Pay Pal + to USPS MO.Please get back off list.
thanks
dale wt4t___
Drakelist
Looking for one of the small black VOX gain or delay knobs for the TR7.
Please email me at: fl...@k8ac.net
73, K8AC
___
Drakelist mailing list
Drakelist@zerobeat.net
http://mailman.zerobeat.net/mailman/listinfo/drakelist
Need help repairing Drake C-Line. Anyone within a couple of hours drive
of Lexington, KY?
TNX
Peter___
Drakelist mailing list
Drakelist@zerobeat.net
http://mailman.zerobeat.net/mailman/listinfo/drakelist
Does anyone have a TR-7 Up-Converter board they would like to sell?
Thanks!
LLOYD-K4HWB___
Drakelist mailing list
Drakelist@zerobeat.net
http://mailman.zerobeat.net/mailman/listinfo/drakelist
Contact Charlie Talbot _pincon@erols.com_ (mailto:pin...@erols.com)
He parts out TR-7s and might well have what you need.
73,
John, W4AWM___
Drakelist mailing list
Drakelist@zerobeat.net
Does anyone have the Email address for John Kriner, KA8GSP or his company
The Mann!! Electronics? I've tried the internet and QRZ but came up
empty.
Thanks,
Bill Taylor
KD4LXC
Woman is 53 But Looks 25
Mom reveals 1 simple wrinkle trick
jkri...@cinci.rr.com___
Drakelist mailing list
Drakelist@zerobeat.net
http://mailman.zerobeat.net/mailman/listinfo/drakelist
I am stil looking to buy a few Stock R4C Xtals. Mine are way off
frequency...they are:
7.0 Mhz (18.1 Mhz)
28.5 Mhz (39.6 Mhz)
These are Stock R4 any Xtals so they aren't scarce.
73
Bill KB9IV___
Drakelist mailing list
Drakelist@zerobeat.net
For some reason...Garey K4OAH...is not getting my e-mails???
Please contact me to do a relay to him.
After the first one comes forward...I'll annouce I have one...so others
can know I have someone.
Thanks,
73,
Lee, KC9CDT
___
Drakelist mailing
thereto.
*From:* Michael Sue Trussell mailto:mtruss8...@comcast.net
*Sent:* Saturday, January 07, 2012 5:33 PM
*To:* drakelist@zerobeat.net mailto:drakelist@zerobeat.net
*Subject:* [Drakelist] Need a fan for my T-4XC Transmitter?
I need to replace my old 30 year old 110 volt fan on my transmitter. I
*Subject:* [Drakelist] Need a fan for my T-4XC Transmitter?
I need to replace my old 30 year old 110 volt fan on my transmitter. I know a few of you have
used the twelve 12 volt fans and some have used the 110 volt version. What I would like to know
where I can get power so I don’t have to plug
Everything on my radio bench is plugged into a suitably large power strip
(I run my T4X barefoot). The wall wart for the fan is plugged into it, as
is the soldering iron. This has the benefit of ensuring nothing is left on
unintentionally.
Chuck, K1OM
On Sat, Jan 7, 2012 at 5:33 PM, Michael
my computers have my signature with various pearls of wisdom appended
thereto.
From: Michael Sue Trussell
Sent: Saturday, January 07, 2012 5:33 PM
To: drakelist@zerobeat.net
Subject: [Drakelist] Need a fan for my T-4XC Transmitter?
I need to replace my old 30 year old 110 volt fan on my
.
John Stark.
All my computers have my signature with various pearls of wisdom appended
thereto.
From: mailto:mtruss8...@comcast.netMichael Sue Trussell
Sent: Saturday, January 07, 2012 5:33 PM
To: mailto:drakelist@zerobeat.netdrakelist@zerobeat.net
Subject: [Drakelist] Need a fan for my T-4XC
5:33 PM
To: drakelist@zerobeat.net
Subject: [Drakelist] Need a fan for my T-4XC Transmitter?
I need to replace my old 30 year old 110 volt fan on my transmitter. I know a
few of you have used the twelve 12 volt fans and some have used the 110 volt
version. What I would like to know where I
I need to replace my old 30 year old 110 volt fan on my transmitter. I know
a few of you have used the twelve 12 volt fans and some have used the 110
volt version. What I would like to know where I can get power so I don't
have to plug the fan in every time I turn the rig on. I would like the fan
See these pics. the power comes from the 12v filament system.
https://picasaweb.google.com/captcurt08/DrakeFanInstall
https://picasaweb.google.com/captcurt08/R4BFan?authkey=Gv1sRgCP_B8eCBk669Wg
If you have any questions, email me.
Curt
KU8L
On 1/7/2012 5:33 PM, Michael Sue Trussell wrote:
Well, given the low cost of surplus DC fans, the low noise when
running them on lower voltages, and the modest energy consumptionI
just leave mine on all the time!
On 1/7/12, Michael Sue Trussell mtruss8...@comcast.net wrote:
I need to replace my old 30 year old 110 volt fan on my
While servicing my R4A my wonderful boatanchor,test gear decided to go south.
I need a alignment done on the receiver ,but my first 2 choices are booked
nearly into summer, anyone have a good service tech that I could use.
thanks
dale wt4t
___
Looking for the plug in AM filter for a R4C.
thanks
dale wt4t
___
Drakelist mailing list
Drakelist@zerobeat.net
http://mailman.zerobeat.net/mailman/listinfo/drakelist
- Original Message -
From: Jim Pruitt wa7...@charter.net
To: Drakelist@zerobeat.net
Sent: Monday, July 18, 2011 6:23 PM
Subject: [Drakelist] Need mic info on Shure model
19B209459P1
I acquired a Shure model 19B209459P1 microphone at a
hamfest a couple monts ago. It looks similar
Dear Drake enthusiasts -
I am looking for a 25.000 mHz overtone crystal for the Drake 2B.
If anyone has one, please contact me directly at k8...@yahoo.com with details.
Thanks and 73,
Jim, K8OZ
___
Drakelist mailing list
I am setting up a 2NT with a VFO. The easiest way to connect seems to
be to connect the output of the vfo to a crystal socket. I would like to
try as a plug an FT-243 crystal holder with the crystal removed and the
vfo output soldered to the two holder pins. Anybody willing to part
with an
Looking for a 17 and 12 meter crystal for a r-4. 29.1 and 35.6. used or nos
or new,please get back off line.
thanks
dale wt4t
___
Drakelist mailing list
Drakelist@zerobeat.net
http://mailman.zerobeat.net/mailman/listinfo/drakelist
I have a working AC-4 for $100 plus shipping.
George K4GM
On 4/3/2011 4:48 PM, y...@aol.com wrote:
Anyone have a AC-4 supply. Plan to rebuild the supply with heathkit
shop board and parts. Will consider all as long as the transformer is
good.
thanks
dale wt4t
please contact me off list.
Hi
Anyone have a ssb filter 2.nd IF 5695 Khz, stock or Inrad, Main tuning
and preselector knob for R-4C. Needed to rebuild my R4-C .
Thanks
73´s
Martin, OZ1CXX
Please contact me off list. m...@forum.dk
___
Drakelist mailing list
Drakelist@zerobeat.net
Anyone have a AC-4 supply. Plan to rebuild the supply with heathkit shop board
and parts. Will consider all as long as the transformer is good.
thanks
dale wt4t
please contact me off list. y...@aol.com
___
Drakelist mailing list
Hi Michael:
That sounds like perhaps a RFI issue. What does the SWR indicate with
the 2700? What does the TR7 Refl indicator show?
I run a TR7 here with a TR7 with and without a linear using the MN2000.
THe Windom I use has real issues with rf on the feed coax above 20M and
even tho the
@zerobeat.net
Sent: Thu, Mar 17, 2011 1:17 pm
Subject: Re: [Drakelist] Need a Tuner for my L4B
Hi Michael:
That sounds like perhaps a RFI issue. What does the SWR indicate with
the 2700? What does the TR7 Refl indicator show?
I run a TR7 here with a TR7 with and without a linear using the MN2000
Fellow enthusiasts,
I'm still trying to get an L-75 working properly. While I have made some
progress (replaced the bandswitch, all fixed capacitors in the output circuit
and RF choke/trap, etc.) there is still a problem remaining. I have identified
three different factory wirings for the
Hi everyone..
Working on a friend's R-4B and I need:
6HS6
12BE6
6EH5
6BZ6
tubes...
Anyone out there that can help out?
He is also looking for a nice T-4XB,AC-4 and MS-4??
PLease contact off list
Thanks,
73,
Lee, KC9CDT
___
Drakelist mailing list
Tonight I found a bad crystal in the R-4B..It is the standard 80 mtr
one ...14.6 mhz
I substituted one I had to cover 3.0 - 3.5 and the 80 mtr position
worked so I know it's the crystal. So I need another one
Also I would like these 3 crystals to add 3 more band segments if
possible:
20.6
Hi gang..working on a R-4b with 9 tubes...lots of corrosion so I can't
read some of the tube types. Letering is worn off tube.
Lots of audo distortion and weak output...think it may be the final AF
amp.
It looks like it might be a 6EH5??
What is the final AF amp tube?
73,
Lee
The audio output tube is the 6EH5. If you are really working on a R4B,
you really need at the minimum the manual, which should be downloadable on
the internet. Really should have Garey's CD with all the manuals and parts
locators for the things you WILL run across during the fix. It pays for
I am working on a Drake UV-3 tri-bander with a non-working 440 Mhz section.
Making progress, however the VCO uses a push-pull arrangement that has the SPF
796 (Drake P/N 3030355) matched pair of JFETs. One JFET had excessive leakage
on its gate so I need to replace. I can't seem to find any
Hello to the list,
I did something stupid and now I need a T-9 (80-20 meter RF coil) for my
TR-4. I assume, but could be wrong, that they are the same for the whole 4
line. I also need a #12 fuse lamp, since there is not one in my TR-4. Does
anyone have these parts that they are willing to
On Sat, 28 Aug 2010 09:24:22 -0600, J. Steven Cochrane wrote:
I did something stupid
C'mon Steve, fess up! What did you do? :)
73
-Jim
--
Ham Radio NU0C
Lincoln, Nebraska, U.S.S.A.
TR7/RV7/R7A/L7, TR6/RV6, T4XC/R4C/L4B, NCL2000, SB104A, R390A, GT550A/RV550A,
HyGain 3750, IBM PS/2 - all
Sent: Saturday, August 28, 2010 11:12 AM
Subject: Re: [Drakelist] Need TR4 T-9
On Sat, 28 Aug 2010 09:24:22 -0600, J. Steven Cochrane wrote:
I did something stupid
C'mon Steve, fess up! What did you do? :)
73
-Jim
--
Ham Radio NU0C
Lincoln, Nebraska, U.S.S.A.
TR7/RV7/R7A/L7, TR6
On Sat, 28 Aug 2010 12:30:08 -0600, J. Steven Cochrane wrote:
That's my story and I'm sticking to it!
Great story, Steve. Thanks for sharing. Don't worry about it, every one of us
has pulled a bonehead stunt like that at some point. More than once, I would
guess.
73
-Jim
--
Ham Radio NU0C
Hi all -- I need a cabinet top for a C line receiver. Seems that the top was
thrown into the dumpster as I tried to rescue it from the Estate
groupies. Can anyone help?
Rick NU7Z
___
Drakelist mailing list
Drakelist@zerobeat.net
Have a nice tr-3 ,but has a mickey mouse pto knob and skirt. Looking for
anything from the origional tr series knob and skirt, to a set ,off a set of
wtins. Will consider all.
thanks
dale wt4t
___
Drakelist mailing list
Drakelist@zerobeat.net
Looking for a ac-4,or even a ac-3 supply. Cosmetics not important,need good
choke and transformer. Will consider all.
thanks
dale wt4t
___
Drakelist mailing list
Drakelist@zerobeat.net
http://mailman.zerobeat.net/mailman/listinfo/drakelist
I'm trying to hook up the low level audio output of my R-7A through an LA-7
and it is distorting the audio. I don't have the same problem with the
TR-7A through the LA-7. A copy of the LA-7 instructions/schematic might
help.
Does anyone have a copy or has anyone experienced a similar
Dave - I have no knowledge of the R7 board and don't have the schematic for
that, but did recently do some work on my TR7 digital control board and will
tell you what I found.
Excuse me if I go over some stuff you already know. U201 is simply a BCD to
Decimal decoder. On the TR7, two
Dave -
I just took a quick look at the schematics for both, and it appears that
the boards ARE the same, with the exception that TR-7 version has
additional logic for the transmit enable function that comes out on
Pin 11. There are also input signals, HB (?) Pin 52, and TX Pin 16.
However!
Hi Dave,
I am now looking at the service manual of TR7. It lists two versions of
digital board. One uses PROM and one uses without. The Drake part number for
the prom is 3040082 at location U201. If the part number is the same on the
R7 manual, I can safely assume they are the same.
With the
Because of an accidental solder bridge [that I put] between the +5 10 V buses
on the underside of the parent board I fried the PROM IC, U201 [P/N 3040082] on
the digital control board. Everything else appears OK but all the PROM outputs
stay low although the enable-not input is low the [4]
Hi Karl,
It has been awhile since I have done anything with my L-4B, but as I
recall, the VOX line needs to be grounded for the relay to pull in. If you are
running a T$-7 or most of the Drake 4 lines, this is easy to do. Otherwise,
simply ground the center conductor of the RCA VOX jack on
On Tue, 15 Dec 2009 20:40:39 EST, w4...@aol.com wrote:
It is not really necessary to connect the AGC line. Your manual should tell
you about these connections.
I would definitely connect the AGC line. It's desirable for some very good
reasons.
73
-Jim
NU0C
--
There are 10 types of people
: [Drakelist] Need Help With L7 NOS Front Panel
Hi All:
I have a NOS front panel for my L7 amplifier. It still has the
original protective plastic covering on it that has become brittle
over the years and is stuck fast to the panel. I tried to scrape it
off with my fingernail and still it doesn't want
is tedious, but at least I now know
how to get the job done.
Again, thanx to all.
73,
Jim
W2BVM
- Original Message
From: Al Parker anc...@ec.rr.com
To: Jim DiMauro radio6...@yahoo.com; Drakelist drakelist@zerobeat.net
Sent: Saturday, August 22, 2009 7:11:06 PM
Subject: Re: [Drakelist] Need
Hi All:
I have a NOS front panel for my L7 amplifier. It still has the original
protective plastic covering on it that has become brittle over the years and is
stuck fast to the panel. I tried to scrape it off with my fingernail and still
it doesn’t want to come off. If I try to use
doing as simply
messing about in boats.
Ratty, to Mole
- Original Message -
From: Jim DiMauro radio6...@yahoo.com
To: Drakelist drakelist@zerobeat.net
Sent: Saturday, August 22, 2009 7:04 PM
Subject: [Drakelist] Need Help With L7 NOS Front Panel
Hi All:
I have a NOS front panel
it with a TR5
panel, and it came out looking perfect.
Ron / WB4HFN
-Original Message-
From: drakelist-boun...@zerobeat.net
[mailto:drakelist-boun...@zerobeat.net] On Behalf Of Jim
DiMauro
Sent: Saturday, August 22, 2009 7:05 PM
To: Drakelist
Subject: [Drakelist] Need Help With L7 NOS Front
Replacing a bad cathode bypass capacitor with a fresh one will increase hum
because the low freq gain will be improved along with better bass response.
But you shouldn't have hum in the speaker anyway (only some residual hum in
headphones at low volume) if the audio stage and B+ feed is operating
I am trying to help another Drake fan, but need some of you fellows
experteeism:
He has hum in his early R-4A including with the AF gain turned to
minimum. He replaced the can-cap in it (this one is the 3-section
version, all 100 mfd) and the hum dropped dramatically.
Apparently there was
Tom,
Does he have a spare audio output tube he can sub in to make sure the tube
itself is not causing the hum?? I would try that first, then look at
coupling capacitors that he hasn't yet changed.
73,
Don, WB5HAK
___
Drakelist mailing list
How much hum and via what output? If I use hi-fi headphones on my tube
gear, I can hear hum. OTOH it is not really noticeable with the speaker.
73,
Ron WD8SBB
--- On Wed, 7/8/09, Tom NØJMY n0...@hayseedhamfest.com wrote:
From: Tom NØJMY n0...@hayseedhamfest.com
Subject: [Drakelist] Need
Hello,
Does anyone have a 38.1 crysta laying around? i need to purchase one so i am
trying here first.suggestions on were to fnd one welcomed.
--
Carey Lockhart, KC5GTT
Boerne, Tx. 78006
www.kc5gtt.com
___
Drakelist mailing list
Drakelist@zerobeat.net
I guess they're not actually knobs...I need the little cylindrical plastic
gizmos that cover the lever switches beneath the Reactive and Resistive
controls. Obtainium?
73,
Jim
W2BVM
___
Drakelist mailing list
Drakelist@zerobeat.net
FYI, Ron Wysong's call is K8AY.
73
Lee WB6SSW
---
No trees were harmed in sending this email,
but a whole lot of electrons were terribly inconvenienced.
**
One
site keeps you connected to all your email: AOL Mail,
Hi-I am trying to help a friend finish his T4X. The function switch needs to be
replaced as it has bad wafers. Anyone have a spare or a junker rig with a good
switch? Thanks in advance and 73 Lew KlNDV___
Drakelist mailing list
Drakelist@zerobeat.net
Fellow Drake enthusiasts,
Would any of you have the contact information for the company that sells
metal blower wheels for the L4B? My understanding is that there is a minimum
order of 300, I don't remember the cost. Somebody had contact info about 3 years
ago on the Drake Technical Net and
Evan -
How about Seven (7)! years?
For those of you need replacement blower wheels for L4and L7
Capewell sells them
Part # 5705-8 137 wheel ,#2.75 CCW 1/4 unit price 16.25 each The fan is no
longer plastic its metal ,
*For complete new blower assembly with motor
2 3/4 115V BV 2751-1a
Sorry for the admin posting: what's the procedure for changing email
address on the list? Unsubscribe the old address and subscribe the new?
--
Peter Alterman, Ph.D.
Asst. CIO for EAuthentication, NIH and
Chair, Federal PKI Policy Authority
2008 03:19
To: [EMAIL PROTECTED]
Subject: Re: [drakelist] Need MS7 label strip and 7-line knobs
[EMAIL PROTECTED] writes:
I also need a set of plastic end strips! John. GI3KDR
John, Archives within the last two weeks had the source information on 7
line end plastic pieces.
Carl
Mike, K4QU, is the man with the end caps for the 7 line.
-Original Message-
From: [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Mon, 19 May 2008 10:18 pm
Subject: Re: [drakelist] Need MS7 label strip and 7-line knobs
[EMAIL PROTECTED] writes:
I also need a set of plastic end strips
[EMAIL PROTECTED] writes:
I also need a set of plastic end strips! John. GI3KDR
John, Archives within the last two weeks had the source information on 7
line end plastic pieces.
Carl Hibbard WD8NHK
**Wondering what's for Dinner Tonight? Get new twists on family
favorites
[EMAIL PROTECTED] made an utterance to the drakelist gang
--
Picked up at Dayton what I THOUGHT was a very nice MS7
speaker...but...on closer inspection, it turns out that persons unknown
substituted the metal MS7 label strip
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of [EMAIL PROTECTED]
Sent: 18 May 2008 11:18
To: [EMAIL PROTECTED]
Subject: [drakelist] Need MS7 label strip and 7-line knobs
[EMAIL PROTECTED] made an utterance to the drakelist gang
[EMAIL PROTECTED] made an utterance to the drakelist gang
--
I can help you with the Mode knob. E-mail me off-list...
--
Submissions:[EMAIL PROTECTED]
Trying to finish up my R4B. Previous owner removed the on-off switch BUT took
the mounting wafer off as well. Anyone have one out of a junker? Have Pay Pal
or cash. Thanks-Lew K1NDV
)
To: [EMAIL PROTECTED]
Sent: Sunday, March 30, 2008 9:49 AM
Subject: [drakelist] Need R4B ON-Off switch
Trying to finish up my R4B. Previous owner removed the on-off switch
BUT took the mounting wafer off as well. Anyone have one out of a junker? Have
Pay Pal or cash. Thanks-Lew K1NDV
K1NDV
---Original Message---
From: Don Cunningham
Date: 03/30/08 11:40:48
To: [EMAIL PROTECTED]
Subject: Re: [drakelist] Need R4B ON-Off switch
Lew,
If you don't find what you need from a donor rig, get in touch with me
direct in a week or so. I am replacing the function switch mechanism
Thank you for the information. I have a little of both I.e. Some corrosion
but also some dust and dirt. Guess I'll break out the swabs!! 73 Lew K1NDV
---Original Message---
From: [EMAIL PROTECTED]
Date: 01/18/08 14:51:25
To: [EMAIL PROTECTED]
Subject: Re: [drakelist] Need on-off
[EMAIL PROTECTED] writes:
Also, could use suggestions on best ways to clean the chassis. Thanks-73
Lew K1NDV
Hi,
Can't help with the switch.
By cleaning do you mean dust dirt removal ? If so rubbing alcohol, or
denatured alcohol and Q-tips.
Others recommend Windex on paper towels.
I am working on my R4B. Previous owner took out the on off switch BUT also took
the metal mounting wafer out too!! Anyone have a spare or a junker available?
Thanks and 73 Lew K1NDV
Sorry for the excess bandwidth but wonder if somebody could help me with an
email problem.? Many messages I receive have a sender's name and email address,
which seem to be related to the Drakelist.? However, there is no indication
that it is from the Drakelist in the send to field, instead the
Jim Pruitt [EMAIL PROTECTED] made an utterance to the drakelist gang
--
Since QTH lists do not seem to want to let me post this, I wonder if anyone
on this list can help me?
Does anyone know of a source for soldering tips for a
Dennis Monticelli [EMAIL PROTECTED] made an utterance to the drakelist gang
--
I don't know, Jim, but I am also interested in a source for tips
because I have a Wen 75 as my backup iron. You may have to find a
parts unit.
On
Jim Pruitt [EMAIL PROTECTED] made an utterance to the drakelist gang
--
Does anyone have or know of a source for the 74LS445, MC14508B, and MC14558B
chips used in the TR7 DR7?
Thank you.
Jim Pruitt
: Saturday, July 28, 2007 3:17 AM
To: [EMAIL PROTECTED]
Subject: [drakelist] Need TR7 DR7 parts source
Jim Pruitt [EMAIL PROTECTED] made an utterance to the drakelist gang
--
Does anyone have or know of a source for the 74LS445
Get hold of Charlie Talbot, K3ICH [EMAIL PROTECTED]He parts out TR-7s
and may have what you need.
73,
John, W4AWM
**
Get a sneak peek of the
all-new AOL at http://discover.aol.com/memed/aolcom30tour
Hi
?Looking for a Cinch type plug #5ab2... for the accy jack on the back of my
r4c. Would like to get 1or 2 plugs.
thanks
dale wt4t
AOL now offers free email to everyone. Find out more about what's free from
AOL at
ectronics.com/lists/pwrcord.htm pages
_
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On
Behalf Of [EMAIL PROTECTED]
Sent: Thursday, June 14, 2007 11:23 AM
To: [EMAIL PROTECTED]
Subject: [drakelist] need accy plug
Hi
Looking for a Cinch type plug #5ab2... for the accy jack
thanks for ythe info ,will check it out.
dale wt4t
-Original Message-
From: Peter Bent [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Thu, 14 Jun 2007 11:42 am
Subject: RE: [drakelist] need accy plug
Have a couple of sources –
do not have any myself
Hi
Does any body have a set ..or either one? ...crystals for 17 meters? for my
r4c. I beleive they are 29.1 and 29.6.would rather try to find older ones
,before trying to order new from jan crystal.
thanks
dale wt4t
Ron Wagner [EMAIL PROTECTED] made an utterance to the drakelist gang
--
I uploaded copies of the various C line that I had to BAMA. Please have a
look there for reasonable copies. bama.sbc.edu
73,
Ron WD8SBB
On Mon, 21 May
Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On
Behalf Of Garey Barrell
Sent: Monday, May 21, 2007 7:09 PM
To: [EMAIL PROTECTED]
Subject: Re: [drakelist] need help with c-line
Garey Barrell [EMAIL PROTECTED] made an utterance to the drakelist gang
Terry
the r4c I have has sn# 25110 .the tx4c is 28937
dale wt4t
-Original Message-
From: Terry Hamilton [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Tue, 22 May 2007 9:01 am
Subject: RE: [drakelist] need help with c-line
Terry Hamilton [EMAIL PROTECTED] made
Garey Barrell [EMAIL PROTECTED] made an utterance to the drakelist gang
--
Terry -
I have all three versions of the R-4B and both versions of the T-4XB
schematics on my CD for the B Line. They are 2-3 MB each because they
Garey Barrell [EMAIL PROTECTED] made an utterance to the drakelist gang
--
Dale -
Your receiver is a very late version 3, (break at 25900,) and the
transmitter is a late version 2 (last version).
I have all four versions of
Maybe a stupid question. have a new too me c line have the receiver
on the bench. added some filters and changed the two lamps. the meter lamp
works fine, the pto lamp won't light, till I supply a hard ground to the
lamp... then lights ok. traced the ground back to the pto/lamp
1 - 100 of 146 matches
Mail list logo