Thanks Tim!
The width setting doesn't affect it here either as it turns out. What does
affect it however is which roofing filter I use which in turn incidentally
is switched by using the width control.
Your findings made me look more and I do still have chirp but with the
different filter
Somebody has asked the same before. But nothing has been replied.
Now I have the same problem.
Page 49 of the KPA100 instructions calls for testing the resistance between
ground and the tab of Q9 on the KPA100 board (or center conductor of the PA
KEY
output jack, J7).
According to the
Has anyone managed to get Fldigi for Windows version 3.12.3 working with
their K3? The last version that worked was 3.11.5.
The new version just hangs, never appears on screen, and has to be
terminated. If I clear the configuration folder it will start, but hangs
when pointed at the K3.xml file.
I have received a couple of direct replies - thanks for the insight.
I did leave out a couple details about the problem. I did not notice it
until after I installed the KAT2.
But also, I had never really used headphones for more than a minute or two
until the day I started hearing this. I
Hi Ed,
The manual indicates that the LED will come on if an unrecognized
command is issued by the controler chip.
Did the modification change anything on the connector J3?
In off-chance, disconnect the two PCBs, clean the connectors and
re-assemble?
Just some off-the cuff thoughts.
Duane
N1BBR
Kurt Wiksten wrote:
Maybe this is not the right forum but...
I want to use my K3 in CW-contests using N1MM software.
I am using a HP-Laptop with Windows XP and the Elecraft KUSB USB to serial
converter.
When working CW I am using my Bencher manipulator connected to the K3.
How do I get the
Julian,
which OS do you use? I'm using fldigi-3.12.3 under Linux (Gentoo,
compiled from the sources) and it works fine. But I'm using the hamlib
functions to control the transceiver and not RigCat...
Regards
Thomas, DL3DTH
Am Dienstag, den 28.07.2009, 08:32 -0700 schrieb Julian, G4ILO:
Has
Thanks for the sugestions Duane, but the mods have nothing to do with the DSP
unit... that's why it is perplexing to me. After the connectors are cleaned
there is no change and even with the mods out of circuit the issue persists.
BTW... all the present mods do is to light LEDs to indicate
Julian,
You might try the fldigi support list, linux...@yahoogroups.com.
Leigh/WA5ZNU
Has anyone managed to get Fldigi for Windows version 3.12.3 working with
their K3? The last version that worked was 3.11.5.
The new version just hangs, never appears on screen, and has to be
terminated. If I
I have noticed some strange behavior in the K3 regarding the noise
blanker (NB) and the sub receiver. If I have the sub receiver turned
off and am listening to the main receiver with the noise blanker turned
on, then enable the sub receiver, the noise blanker is turned off in the
main
Sent from my iPhone
Begin forwarded message:
From: Karl MARDERIAN karl...@sbcglobal.net
Date: July 27, 2009 12:32:11 PM PDT
To: elecr...@mail.qth.net
Subject: LP Pan sound card
Can one use a laptop with the LP Pan? Or do you need a an advanced
sound card.
I personally would be using
Karl,
You can but performance will suffer.
You'll more than likely be limited to 48 or 96Khz of display.
The USB E-MU 0202 will do much better if your laptop has the horse power
to run it.
Karl MARDERIAN wrote:
Can one use a laptop with the LP Pan? Or do you need a an advanced
sound card.
Yes, of course. And verified the dummy load was working correctly with
an MFJ 259.
N5GE wrote:
Doug Person wrote:
Hi Folks,
Installing the KPA3 and KAT3 is pretty straight forward. That's why
I don't understand what's wrong. Looks like ANT1 and ANT2 are both
open. I can see the
If the Mac is one of the reasonably recent Core (2) Duo models, it should be
able to handle the EMU-0202 at full b/w...
~Iain
On Tue, Jul 28, 2009 at 11:45 AM, R. Kevin Stover rksto...@mchsi.comwrote:
Karl,
You can but performance will suffer.
You'll more than likely be limited to 48
On Jul 28, 2009, at 12:02 PM, Iain MacDonnell - N6ML wrote:
If the Mac is one of the reasonably recent Core (2) Duo models, it
should be
able to handle the EMU-0202 at full b/w...
Unless E-MU has updated their Mac OS X drivers recently, you can use
the E-MU 0202 and 0404 only up to 96k
On Jul 28, 2009, at 12:14 PM, Kok Chen wrote:
Unless E-MU has updated their Mac OS X drivers recently, you can use
the E-MU 0202 and 0404 only up to 96k samples/sec with a Mac
My mistake.
Iain has informed me that the original poster has intended to use
Bootcamp. In that case, the E-MU
The problem seems to be that I am using the Virtual Serial Port Emulator
software to allow multiple programs such as KTune and KComm to control the
K3 at the same time as Fldigi. Something has changed in the latest version
of Fldigi so that it will no longer work with VSPE. Not even Hamlib will
I removed the KAT3 and reinstalled the KANT3. SWR now normal.
Doug -- K0DXV
At 22:59 07/27/2009, you wrote:
Hi Folks,
Installing the KPA3 and KAT3 is pretty straight forward. That's why I
don't understand what's wrong. Looks like ANT1 and ANT2 are both open.
I can see the leads
Dieter,
The link to the K2 LEDs page is http://www.qslnet.de/member/la3za/K2_LEDS.html
and a K2 mod page at http://www.qslnet.de/member/la3za/
73,
Ed
AD7GR - NE Oregon
Novice WDØDRL -CO-1977- Extra since 1984
- Original Message
From: Dieter Mayr d.m...@aon.at
To: Ed K
Battery reads good... 6.2vdc. My DVM may not be dead on but it reads very
close.
Disconnecting and reinserting the battery only resets the clock as I recall.
When I substitute my KAF2 I have audio... only the KDSP2 itself is
malfunctioning.
Ed
- Original Message
From: dw
Hideki,
With power off, check the resistance from the source of Q9 to ground.
If you can check from the lead of Q9 rather than the solder connection.
If it is not zero ohms, you have a soldering problem there.
If the source of Q9 is well grounded, next check the voltage at the Q9
gate
Ed,
Check the soldering for the headers that connect the DSP module to the
board. If there was a marginal solder connection, removing and
re-inserting the module may have made it non-functional.
Did you use good anti-static measures when the DSP module was removed,
stored while it was out of
Charles,
There's a setting in the menu to remember the NB settings.
Switch that on and the problem is solved.
73,
Arie PA3A
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens Charles Johnson
Verzonden: dinsdag 28 juli 2009
Your opinion is valued.
I recently completed my K2. And was thinking of adding DSP.
As a CW op only, would the KDSP2 be a good addition?
Best regards
Dick AD1G
__
Elecraft mailing list
Home:
I suspect there are different opinions, but mine is that it
definitely improves performance. I was amazed at the effectiveness
of the noise reduction, for example.
Bob, N7XY
On Jul 28, 2009, at 6:09 PM, richard gilley wrote:
Your opinion is valued.
I recently completed my K2. And was
Thank you. I've sent your problem report off to the fldigi development
list.
Leigh/WA5ZNU
The problem seems to be that I am using the Virtual Serial Port Emulator
software to allow multiple programs such as KTune and KComm to control the
K3 at the same time as Fldigi. Something has changed in
26 matches
Mail list logo
