__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
That's interesting, the RX I/Q signal lines appear to be reversed when
operating the KX3 on 2m.
I guess this makes sense, if you consider the 2m module is using the x4
output of the KX3's local oscillator, so that if you tune to 144MHz for
example, the LO would be running at 48MHz, so that in
I just found out that there's a Rework Kit E850607 for the KPA500. It
replaces Q5 (a FET) with a Darlington Transistor. The kit also includes a
Zener Diode, resistors and capacitors and includes changes to the 12 meter
LP filter. The kit applies to board REV D9 or earlier.
-
Jack WA9FVP
Of course, this is taken care of automatically in the PX3 :-)
Many of the better SDR Console software packages include a
configuration option to swap I/Q above 'N' MHz ... works for
KX3 on 144 MHz and K3 on 50 MHz.
73,
... Joe, W4TV
On 2014-11-03 9:41 AM, Matt VK2RQ wrote:
That's
I bet this has been asked and answered before. My new amp works perfectly.
Another engineering masterpiece from Elecraft. Is it normal for the amp to
be warm all the time whether it is on or off? Mine feels warm on the
bottom and shows about 32C when everything else in the shack is 24C to
On Mon, 3 Nov 2014 19:04:27 -0500, Barry Boothe via Elecraft wrote:
Is it normal for the amp to
be warm all the time whether it is on or off? Mine feels warm on the
bottom and shows about 32C when everything else in the shack is 24C to 26C.
I have not turned mine over to see how warm it
Hello Bob,
I would like to thank YOU for your trip to 4W. I was down to my last 4
zones needed on 80M and putting you in the log recently took that number
down to three zones left. Fantastic job with an HF9V for sure! You had
a very good signal on 80M.
The best part was a confirmation on
Nice site, Jim. Thanks for the link. Very nice
instructions on the amp, too.
Phil W7OX
On 11/1/14, 7:58 AM, James Bennett wrote:
Another option for a tad more power is to roll you own. W6PQL had an article
in the May 2013 issue of QST for building an 80 watt out all mode 2 meter amp:
Hello all,
I have spent a few months trying to fathom this and finally have given
up and need your help...
When in CW mode, and running MixW the following is observed:
1. All bands below 18 MHz, if I move the tuning dial, the frequency
display of MixW moves as expected, and any signals stay
This is on a K3
--
Thanks and 73's,
For equipment, and software setups and reviews see:
www.nk7z.net
for MixW support see;
http://groups.yahoo.com/neo/groups/mixw/info
for Dopplergram information see:
http://groups.yahoo.com/neo/groups/dopplergram/info
for MM-SSTV see:
You may have to put it in CW-R mode to get on the opposite sideband. Â Although
I would think one would use digital soundcard programs in DATA-A mode.
Sent from my U.S. Cellular® Smartphone
div Original message /divdivFrom: David Cole
d...@nk7z.net /divdivDate:11/03/2014 8:53
Hi,
I have tried that... Same thing happens, the radio acts exactly the
same... It is some interaction with MixW I think... If I load FLDigi,
I get the same action, only all the time... I have disabled the
bands.ini in MixW to test, and that seems to make no difference...
--
Thanks and
I generally operate CW at 20KHz spans, with the bottom edge of the
screen at an even 20 KHz boundary. Seems to work well, occasionally
I'll find it different, not sure why.
In SS CW, I noticed that my lower span boundary was often 5 KHz up from
the normal value ... such as 14025. It seemed
Here is the net report for the Elecraft SSB net from November 2, 2014. We had
26 participants.
Station NameQTH Rig S/N
KM4IK Ian GA K3 281
W0CZKen ND
Hi Fred,
When the K3 VFO A frequency gets outside of the P3 displayed span, the
P3 center frequency may change to keep VFO A on-screen, depending on the
setting of the FixMode menu setting. If you set FixMode to Static
then the displayed range should not change no matter what the K3 is
Hi Gary,
I will be one of the 3 operators from 8Q7DV (zone 22) during CQWW CW. We
are leaving from home on the 22nd of Nov and returning on the 4th of Dec so
there will be time before and after the contest. . Sure enough all the rigs
will be by Elecraft (actually a pair of K3 and possibly one
David == David Cole d...@nk7z.net writes:
David Hi,
David I have tried that... Same thing happens, the radio acts exactly the
David same... It is some interaction with MixW I think... If I
David load FLDigi,
David I get the same action, only all the time... I have
17 matches
Mail list logo