Michael,
There is no one answer. Does your KX3 operate in voice modes when using
the microphone? If so, there is not a likely problem with the KX3.
Investigate your computer sound card levels to assure that you have
adequate audio levels going to the KX3. You should drive the ALC meter
on
Not enough audio from the computer, not enough Mic Gain? Wrong sound
card selected in Fldigi?
73,
matt
W6NIA
On Mon, 13 Jul 2015 21:20:02 -0400, you wrote:
All,
I have my KX3 connected to a computer and am running FLdigi. For psk31, I
set the KX3 to VOX, and the mode to DATA-A. When I
This looks really cool. Thanks for sharing.
-Nate Burr
KG7PXY
On Jul 13, 2015, at 7:58 PM, inventor61 . invento...@gmail.com wrote:
As an alternative to the Kickstarter project ...
The HobbyPCB RS-UV3 triband FM VHF/UHF building block is also available
(shipping now, no pledge needed),
Hi Andy,
The datasheet for the poly cap is shown here:
http://nichicon-us.com/english/products/pdfs/e-l8.pdf
The cap can be ordered from Digikey as p/n 493-4026-1-ND, or as part
of the Elecraft KBPF3MDKT modification kit.
The cap fits comfortably below the KNB3 board on both main and
It does not compute to order the kit as the postage is too high and the
capacitors appear to be relatively easily available. So my question is what
physical size is the 220mfd solid polymer cap used to bypass the zener in the
BPF mods (enabling reception down to 500KHz). It would appear to be a
Full-sized whip on a VW Beetle? I thought there for a moment maybe you were
the guy with the VW on the cover of CQ for September 1961:
http://hamcall.net/cqcgi/?res=lyr=1961mo=09pg=001
That _had_ to be pretty efficient for a mobile antenna. As I recall from
reading about it originally when I
Thanks that's most appreciated.
Andy
Original message
From : mzil...@roadrunner.com
Date : 13/07/2015 - 15:19 (GMTDT)
To : andy.ne...@btinternet.com
Cc : elecraft@mailman.qth.net
Subject : Re: [Elecraft] Size of 220mfd cap for BPF
Hi Andy,
The datasheet for the poly cap is shown here:
As an alternative to the Kickstarter project ...
The HobbyPCB RS-UV3 triband FM VHF/UHF building block is also available
(shipping now, no pledge needed), has a really superbly designed RF
section, can operate independently from an Arduino, plugs into an Arduino
as a shield if desired, and has
FOR SALE - ELECRAFT KX3 PX3 PANADAPTER
Both the KX3 PX3 are in excellent LIKE NEW CONDITION. Never used in mobile
or portable operation, used strictly as a base station.
KX3 Serial # 3XXX
PX3 Serial # X5XX
KX3 Includes the Following:
KXFL3 Dual-Passband Roofing Filters, FL1 (500/1000HZ),
The Err can show up for several reasons that are not really errors, ie supply
voltage to low for battery level. I would try the old batteries again,
should have been fine. The charger uses 200 ma constant current no matter
how long charge time is set. That is low enough that 2 hrs or 4 hrs
For Sale Elecraft K3/100
Serial Number: 6001
K3/100 - 100 Watt
KAT3 Antenna Tuner
KXV3A Rcv. Antenna / IF Out / Xverter Interface
KFL3A - 2.8 8 Pole Filter
KF3LA - 400 8 Pole Filter
KFL3B - FM 8 Pole Filter
KBPF3 - General Coverage Rcv. Module
Excellent Condition no marks/scratches
Operates as
Last night during one of my frequent (at times) recharging of my KX3 batteries,
I noticed that the charging in a 4-hour cycle stopped with an error after about
2 hours. The VFO-B display of menu status said ERR (probably battery ERR but I
forgot to write it down).
I took all the batteries
Gary,
Since you get no ALC bars when the fault occurs, the problem is either
in your Signalink or the audio input section of the KX3.
It could be as simple as an intermittent audio cable connection or a
fault in the audio wire.
If you have an audio amplifier available (like one of those used
While your test using a dummy load seem reasonable and correct, it would
appear as though you may have an excessive amount of Common Mode current
on the feed line, not being seen by the SWR indication in the radio. I
suggest a Common Mode choke on and at the output of the radio. Perhaps
a
Just as background, this digital setup has been working successfully for
several weeks and as I mentioned in another post I've recently had over
170 contacts in both JT65/JT9 running 5 or 10W (my KX3 has 3rd third
party heatsink). The ALC was appropriately set based on information Don
On 2015-07-13 10:41 AM, rlsla...@gmail.com [Elecraft_K3] wrote:
... I suspect some new firmware to test shortly!
Don't count on it. The filter offsets *are* matched for all
8-pole (250, 500, 1000, 1800, 2100, 2800, 6000, 13000 Hz) filters.
When using a receive bandwidth greater than 2800 Hz
I saw this and thought others may be interested in something like this.
https://www.kickstarter.com/projects/749835103/hamshield-for-arduino-vhf-uhf-transceiver
https://www.kickstarter.com/projects/749835103/hamshield-for-arduino-vhf-uhf-transceiver
It’s an FM transceiver that interfaces with
Hi,
I have added a bit more information to the pages which show the new vs.
old synthesizer differences. Just some clarification comments is all.
Page is at:
http://nk7z.net/wiki/elecraft-k3-macros/elecraft-k3-xlr-to-radio/elecraft-k3-new-synthesizer/
--
Thanks and 73's,
For equipment, and
On 07/13/2015 06:17 AM, Al Gulseth wrote:
Full-sized whip on a VW Beetle? I thought there for a moment maybe you were
the guy with the VW on the cover of CQ for September 1961:
http://hamcall.net/cqcgi/?res=lyr=1961mo=09pg=001
No no, it was a full-sized *CB* whip on a Beetle! About 9 feet
Hello
Is there now, or will there soon be, a video of this unit in operation?
Thanks
Steve KZ1X
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Proud owner of K3, S/N 6001!
Cannot wait!
Frank KG9H
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
I had asked about how to power a Unbranded (Best Buy) Windows 8.1 tablet while
using the
one micro USB for data as well as charging. I received several good
suggestions but have
found another solution.
I bought a DIgi Anywhere USB/5, which allows connecting to 5 USB ports over
Ethernet.
Phil,
In addition to the items already mentioned, be sure that the plug on the
battery pack leads is fully engaged onto the pins on the circuit board. When I
first received my KX3, I had similar symptoms, and that was what the problem
was. (Not Elecraft's fault).
MarkKE6BB
This may not apply to Gary Hawkins' situation with his KX3, but I
have the situation where I get no Tx audio drive to my K3 in digital
modes from the soundcard. Turns out that my XP32 computer is not
doing a handshake at power-up with my emu-0202. Cure is to cycle the
power on the emu0202 to
I purchased this before I found out I didn't need it for the K3. Hooked it up
but never used it. Comes with K3 cable
If interested, contact me off list at:hsherr...@reagan.com
Sent from my Verizon Wireless 4G LTE smartphone
__
Phil,
Check those batteries carefully while they are mounted in the KX3. It
sounds like some of the contacts on the batteries is not making proper
contact with the battery holders. Slightly oversize battery cylinder
diameter, slightly recessed battery contacts, stuff like that can cause
All,
I have my KX3 connected to a computer and am running FLdigi. For psk31, I
set the KX3 to VOX, and the mode to DATA-A. When I send characters from the
FLdigi, I see no bars in the ALC display. What could be wrong?
Michael N3IRT
27 matches
Mail list logo