I had a plan to set up one of my shack K3 rigs as a remote control station
to be used with a K3/0-Mini but have abandoned the plan due to changing
interests and need to raise $$$ to pursue them.
This complete package costs $1320 at current Elecraft packaging.
This package has only been
Folks - Let's rest this thread for now as we have seen a number of posting on
this OT today.
Thread closed.
73,
Eric
Lost moderator
/elecraft.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Dang it... don't know why my setup is adding those asterisks and screwing up
the links... Here they are again:
http://montac.com/images/antenna/tilt_base_iso.jpg
http://montac.com/images/antenna/tilt_base_front.jpg
http://montac.com/images/antenna/tilt_base_top_pin_pulled.jpg
Putting up a multi-band, horizontally oriented loop and I have ZERO
trees in my yard. I am borrowing trees from my two next door neighbors,
but I needed to supply one support for a delta config (yes, I'd prefer a
square).
Didn't like the commercial telescoping masts available, so I designed my
Elecraft recently posted a modification to the K3REF to correct a problem
caused by the K3EXREF. Though specific to frequency changes noticeable on
on 2M and 6M, I suspect it may directly relate to this discussion.
http://www.elecraft.com/K3/mods/K3EXREF%20freq%20shift%20fix.pdf
---
Chuck, AE4CW
Alan,
Thank you for such a clear explanation! I understood the process, and
why, but having someone actually put numbers to it helps in getting
that "gut feeling" as to why... Thank you!!
--
73's, and thanks,
Dave (NK7Z)
For software/hardware reviews see:
http://www.nk7z.net
For MixW support
When Eric VA7DZ, Fred KE7X and I were all experimenting with KRC2s for
our K3s, I also connected mine to the KX3 with the help of Jack Brindle,
KRC2 expert.
Here's what I did to the KRC2 to make it work in between the KX3 and the
computer:
1. Set KX3 menu item RS232 to 19200b. Set the
Thanks, Brendon. Hopefully the miniaturization offered by SMT reduces
the size of the antennas that radiate any trash. :) But that may be
wishful thinking -- W6GJB encountered massive noise on HF that he
tracked down to computer extension speakers with built-in power amps
that were powered
Without repeating a long response to my long post, we do agree on all
key points. Including the fact that the vast majority of manufacturers
get shield bonding wrong.
Here's a link to Henry Ott's website. Scroll down to find a reference to
the latest edition of his book. It is often used as a
I'm on the market for a one or two ft long RG-142 with Crimped BNC Angle Male
on one end and crimped UHF Male on the other end. Could you lead me to a good
source, please?
73,
Luciano PT9KK
__
Elecraft mailing list
Home:
On 3/7/2016 11:56 PM, Jim Brown wrote:
> Actually, switch-mode power supplies run in the range of 10-50 kHz,
> NOT at HF. It is the unfiltered high order harmonics that we hear at HF.
Yep... I was wrong, you are right. Not fundamental, but harmonics. I
should stop writing in the middle of
I would like to try a remote setup from my Florida location that is
antenna restricted. To that end I am looking for a used K3/0 Mini to
experiment with. If anyone has a unit excess to their needs, please
let me know.
Bill
WA8CDU
On 3/8/2016 3:04 AM, Greg VK3VT wrote:
>
> You could get an LP Pan panadapter
> (http://www.telepostinc.com/LP-PAN.html)
and this will allow you receive on a second frequency on your
computer using the VFO B knob to tune (distance from VFO A
determined by the sound card you use - panadapter
While not specific to Elecraft, I'm forwarding this to the reflector because
there has been a lot of discussion from time to time about the use of code
readers and the like. The best code reader is your brain and you can learn
CW as evidenced by the high success rate of the CWA. If you are a
Bob,
Are you driving the audio level sufficiently? Inadequate audio drive is
a common cause of such 'power hunting'.
You can do this off the air - turn the power to zero or connect a dummy
load.
Then turn compression to zero.
Talk normally into the microphone and adjust the MIC GAIN to
Just an unsolicited tribute to the K3's diversity feature. I had been
trying to work 8R1/K9XK in Guyana for a few days without success.
Although I usually do OK with that part of the world, he's been too deep
in the noise. I finally caught the propagation on 17 meters this
afternoon and could
Almost.
The TCXO has no control input and is not tuned; it is only measured.
The measurement information is passed to the radio's MCU which then uses
the data to determine the correct value to command the synthesizer(s),
drive the REF CAL display, and so forth.
73,
Lyle KK7P
The K3EXREF
Hi All
I am new to this list and hope this has not been raised before.
I have a new KX3 with the up to date firmware, this radio is a replacement
for the original KX3 that had the same thing happening.
When you go to 15Mtrs on USB from a different band the output power is very
low on the output
Thanks guys for the detailed and thorough replies - I understand it now!!
Andy G4HUE
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Ross (W6FG)
You could get an LP Pan panadapter (http://www.telepostinc.com/LP-PAN.html)
and this will allow you receive on a second frequency on your computer using
the VFO B knob to tune (distance from VFO A determined by the sound card you
use - panadapter bandwidth can be up to 192KHz). You
20 matches
Mail list logo
