Re: [Elecraft] KX1 build issue after Part 1 of build

Thanks Rod, That fits with my ideas which I put in my last post where I talk about the solution to the problem. But I didn't have a reason for the one digit being brighter. Your idea would complete my theory. 73, --Frank -- View this message in context:

[Elecraft] FS: K3 and P3

I'm selling my K3 and P3. (Overwhelmed by medical bills and need a new car) The K3 has all the upgrades (KIO3B, K3SYN3, NEOGRIP). Also has KAT3A internal tuner and KPA3A 100 watt internal amplifier. Includes KDVR3 which has not been installed and is still in original unopened bag. Finally,

Re: [Elecraft] FS (2) RemoteRig RC-1216H

SOLD Thank You On 5/5/2016 1:23 PM, 'DGB' wrote: I have two RemoteRig RC-1216H units that are surplus to my needs. These are Web based remote controls for SteppIR, ACOM-2000A, Expert 1K-FA,Elecraft KPA500 and Rotators and more. Also have the .PDF user manual. Asking $225 each or $425 for

[Elecraft] Problem with KAT2 Bridge Null Adjustment

Thanks, Don. I did check that, and redid all of T1’s solder joints. No change. I was about to rewind T1 altogether when I decided to check the archives. Using a search method earlier suggested by Phil, W7OX, I found a post by you in 2013 answering the very same question. On reading it

Re: [Elecraft] KX1 build issue after Part 1 of build

I found a solution. I noticed that pressure on the power connector would sometimes cause a reboot. Reflowing a second time with more solder in that area cleared up all my problems. My theory is that short interruptions in power made the system glitch and create the symptoms. Remember that the

Re: [Elecraft] Problem with KAT2 Bridge Null Adjustment

Ted, You will find the problem is with T1. It must be wound and installed exactly as shown in the manual, and that includes the direction of the winding. Your K2 is likely putting out all the power it is capable of, so do those TUNEs for only a short period or you will be replacing the PA

[Elecraft] Problem with KAT2 Bridge Null Adjustment

Advice requested for the following problem: Completed and installed the KIO2. That works fine, so far as it has been tested with the outboard ("twins") KPA100 and KAT100. Next step was to put the amp and high power tuner aside and install a KAT2 in the base K2. [In case it matters, the K2

Re: [Elecraft] New Elecraft Product for Dayton?

I've got that covered. I've got a Lincoln Power MIG 216 welder. On 5/7/2016 7:21 AM, Henry Pollock - K4TMC wrote: For the 'Kit Version' you will have to upgrade your soldering gear to welding equipment! Why wasn't this subject started back on April 1st? 73, Henry - K4TMC -- R. Kevin Stover

Re: [Elecraft] New Elecraft Product for Dayton?

For the 'Kit Version' you will have to upgrade your soldering gear to welding equipment! Why wasn't this subject started back on April 1st? 73, Henry - K4TMC On Fri, May 6, 2016 at 9:36 PM, Rick WA6NHC wrote: > As with all things Elecraft, the new K-room is configurable any

Re: [Elecraft] New Elecraft Product for Dayton?

Whewi started to design a new trailer for the Motorhome so I could upgrade. Gary -Original Message- From: "lstavenhagen" Sent: ‎7/‎05/‎2016 12:27 PM To: "elecraft@mailman.qth.net" Subject: Re: [Elecraft] New Elecraft Product for