The RigExpert TI-5 has been sold. Thanks for looking. Max NG7M
On Sat, Mar 25, 2017 at 9:42 AM, M. George
wrote:
> Up for sale if my RigExpert TI-5 with factory K3 cable set, original box,
> manual etc...
>
> If someone wants to add KIO3B functionality to their K3
Good Evening,
After two spotless weeks the sun has a new speckle. There was a
decent solar breeze earlier in the week too. Auspicious thoughts here.
I am hoping for more band noise and better reception. They seem to
correlate. If the band sounds like I am in the middle of cotton ball
Hi everyone
I have managed to get the encoder turning reasonable freely. I put a
very small amout of WD40 on the shaft where it enters the housing bush.
And then did as Don suggested repeatedly and firmly pushed the knob up
at the low point. After quite a lot of pushing it began to loosen up
On 3/25/2017 1:26 PM, Al Lorona wrote:
However, the paper had simply repeated what was in another paper
that's been out there for years. Jack Smith, K8ZOA, made much
better measurements that I would encourage anybody to read.
However, I've been told that DX Engineering, which acquired Jack's
Selling the house and moving to an apartment so selling my beloved Elecraft
K line.
K3 serial # 758
100 w module
KRX3-F 2ND RECEIVER Factory installed
KFL3A 250 HZ 8 POLE FILTERS (2) Factory installed.
KFL3A -500 HZ Factory installed.
KDVR3 Digital Voice Recorder Factory Installed
That paper is based on the old AGC parameter ranges. They were expanded
by firmware 4.51
A more recent discussion with charts can be found on Fred Cady's website
http://www.ke7x.com/home/miscellaneous-k3-information/agc-4-51.
There is additional information in my website "Noisy K3" article
The Clifton Laboratories paper from 2009 is still obtainable via the Internet
Archive's Wayback Machine at this link:
https://web.archive.org/web/20161225060408/http://cliftonlaboratories.com/Documents/Elecraft%20K3%20Transceiver%20AGC%20Parameters%20and%20S-meter.pdf
-Brian, N9ADG
Just wondering if it will be replaced with another model!!
Ken.. G0ORH
Sent from my iPad
> On 25 Mar 2017, at 17:26, Al Lorona wrote:
>
>
> You probably remember that I recently put out a little tutorial to the group
> on the K3 AGC. Immediately after I put those
If it doesn’t (or can’t) show up in firmware, there are external solutions that
can accomplish this — for example the Buddipole PowerMini. I keep one in-line,
even without a solar panel connected for just this purpose. It will both alarm
and disconnect the external battery when it reaches a
You probably remember that I recently put out a little tutorial to the group on
the K3 AGC. Immediately after I put those measurements out there, some of the
gurus here told me that it could be confusing, and might be misunderstood, so I
pulled it. I don't know who told the ARRL Contest
FS: MicroHam DigiKeyer II
- Very good unit with cable for Elecraft K3. Original boxes and disc.
Will include extra cost numeric key pad. $265 shipped conus.
- Jeff @ k...@att.net
-
__
Elecraft mailing list
Right now there is just the "Bat Min" setting that gives an alarm if the
present voltage drops to a set value in the configuration menu. (Automatic
shutdown happens at 7.0V according to the manual.) I use an external LiFePO4,
and internal NiMH. These have different specs. I would like to see
Up for sale if my RigExpert TI-5 with factory K3 cable set, original box,
manual etc...
If someone wants to add KIO3B functionality to their K3 for a lot less than
the upgrade to the KIO3B, this is a very clean and slick solution. With
the TI-5, you have one USB cable to your computer and then
Make sure the KPA3A is enabled in the CONFIG menu.
73,
Brian, K0DTJ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list
On 3/25/2017 7:36 AM, efortner wrote:
...
WMTR HP. The power control will not go past 12 watts. The auto calibration
works fine on 5 watts but when finished next takes me to the 1 milliwatt cal
instead of 50 watts. Following directions to set power to 50 watts does not
work.
Any suggestions.
Hello,
Doing some downsizing and I have the following for sale.
Pelican 1400 Case Yellow
Foam is cut out for a K2 radio.
Asking $70 shipped to the lower 48 States.
Please email me direct.
73
Ron Polityka
WB3AAL
__
Elecraft mailing
I have had a glitch in my software and trying to reconfiger my K3s. The tx
filters got switched in the software some how. I now have the filters sorted
out but doing the wattmeter calibration and cannot get Config WMTR LP to
change to
WMTR HP. The power control will not go past 12 watts. The
Perhaps a new, legal limit power amplifier should be non-linear so as to
achieve very high efficiency. Broadcasters seem to use such designs
routinely, and the latest QEX described a ham version under development.
__
Elecraft mailing
18 matches
Mail list logo