Re: [Elecraft] Wanted: KXV3

Thanks to all who responded. A board will be on its way to me soon. 73, Wayne K2DT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

Re: [Elecraft] [K2] Sensitivity Spec

Steve, I ran your parameters thru my NF program for three stages using: 1.2 dBNF of 1st stage with 17-dB gain (typical DEMI 10-GHz xvtr spec) followed by 0.1 dB cable loss 1.0 dBNF 2nd stage which nominal for a 144-MHz xvtr and used 10-dB gain followed by0.1 dB cable loss K2 10-dBNF Bw = 500 Hz

Re: [Elecraft] PX3 Lag

Scott, This is definitely a bug, and it’s in my court. Sorry for not responding sooner. I’ll be working on it when I get back from vacation in about a week. 73, Wayne N6KR > On Aug 16, 2017, at 6:59 PM, Scott Russell wrote: > > Roger, > > I found this same issue when

Re: [Elecraft] K2 Display OTS - Request Advice . . . . .

Ted, A blank display is quite unusual. Does "Elecraft" display when the K2 is powered on? First check the DC voltage at the anodes of D6 and D7. In receive D6 should be near 8 volts while D7 anode should be near zero volts. If there is voltage at the anode of D7, the K2 is going into

Re: [Elecraft] PX3 Lag

Roger, I found this same issue when I added the KXPA100 back in the March timeframe. I posted here on the Elecraft list and shortly started an email dialog with Paul, one of Elecrafts Senior Software Engineers. After some testing it was determined that they could re-create the problem and that a

[Elecraft] K2

Test -- R. Kevin StoverAC0H FISTS #11993 SKCC #215 NAQCC #3441 ARRL __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This

[Elecraft] Puzzling packages

Hi Gang! I have two anti-static bags from Elecraft, both labeled "E850235 K3 Digital IO PCB Assm". One package is marked in red pen "Old" and the board in the package is marked "K103 REMOTE I/O MODULE Rev B". The other package is labeled identically, except W/O the handwritten "OLD". The board

[Elecraft] K2 Display OTS - Request Advice . . . . .

The display on my K2 (S/N 7637) just quit. The backlight is on, but not a single digit component appears. The rig has been working FB for over a year. Used it today as the alignment receiver for another K2 being built. All was fine when that process started, both rigs worked as they should,

Re: [Elecraft] PX3 Lag

I haven't verified this, but one thing you might try is to turn PA MODE to OFF on the KX3. You'll then need to turn on/off the KXPA100 manually since the KX3 will no longer be pinging the KXPA100. This should eliminate the cursor/marker lag on the PX3. Kindly, Paul -- View this message

[Elecraft] Camino de Santiago portable operation from Spain

Hi Elecrafters, I'm not sure this is the right place for this, and if not, maybe some of you can point me in the right direction for a more suitable place to post, but I did talk to Wayne about this at Dayton this year. My wife and I are going to do another leg of the Camino de Santiago next

Re: [Elecraft] XMIT button not working in DATA-A mode

On 8/16/2017 12:27 PM, Gene O wrote: > K3 -- While in Data-A mode, I press the XMIT button and the unit does > not transmit fully. Is the K3 in SPLIT? 73, ... Joe, W4TV On 8/16/2017 12:27 PM, Gene O wrote: K3 -- While in Data-A mode, I press the XMIT button and the unit does not transmit

Re: [Elecraft] [K2] Sensitivity Spec

Thanks for your comments, Don. When you test K2's, can I assume you have the signal generator connected directly to the K2 (or through an attenuator) with no antenna connected? Normally, one might hope that a preamp would provide some improvement in receiver noise figure (and hence MDS,

Re: [Elecraft] PX3 Lag

If I remember correctly this is the result of loading on the serial data port. -- View this message in context: http://elecraft.365791.n2.nabble.com/PX3-Lag-tp7633439p7633444.html Sent from the Elecraft mailing list archive at Nabble.com.

[Elecraft] XMIT button not working in DATA-A mode

K3 -- While in Data-A mode, I press the XMIT button and the unit does not transmit fully. It sort of goes into oscillation is the best I can describe it. I am transmitting into a dummy load at about 20 watts. I first noticed this while using WJST F8. At that time I thought this was feed

[Elecraft] KXPA100 Feature request

In addition to my previous post… If ATU-Mod is saved per Antenna, then one could switch, and compare instantly the results, eg. antenna 1 with or without internal tuner, and antenna 2 directly connected or with external tuner, on the same band. 73, Gerald - HB9CEY Hello All My activ setup here

Re: [Elecraft] Win4K3 and Elad S2

I don't believe the Elad is supported... I would ask Tom via the support email listed on the Win4K3 website, he is very responsive. mg NG7M On Wed, Aug 16, 2017 at 6:50 AM, Dan Atchison via Elecraft < elecraft@mailman.qth.net> wrote: > Has anyone successfully installed Win4K3 + an Elad FDM-S2

[Elecraft] WTB - KXAT2

Seeking ATU (KXAT2) board for my KX2. Anyone have one they can part with? Very 73, Mike NK8S Nasty Kharybdis 8 Sailors FISTS #17907 NAQCC #8554 SKCC #15862T​ __ Elecraft mailing list Home:

[Elecraft] PX3 Lag

I recently got a KXPA100. Ever since I hooked it up I noticed that the PX3 marker no longer moves "smooth." It will move across the screen smooth for a bit, lag behind in frequency, then jump to where it should be and then continue. I thought it was a fluke at first but it does it quite

[Elecraft] Win4K3 and Elad S2

Has anyone successfully installed Win4K3 + an Elad FDM-S2 for spectrum control? 73, Dan __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

[Elecraft] Update on the Y-BOX breakout box / ACC splitter for the K3 and K3S

To review, the Y-BOX is a flexible 1x4 splitter and breakout box designed to make it easier to connect multiple devices in parallel to the accessory port of an Elecraft K3 or K3S (or to any device with a DE-15 connector, including ACOM amps, the FlexRadio Flex-6000 series, and the 4O3A Antenna

Re: [Elecraft] Rx antenna protection

DXE ARAV3-1P - DXE RG 5000HD. I've ordered a DXE ARAVS-1P Receive antenna, and DXE RG 5000HD front end protector from USA, I'm building a CW skimmer project in a small ...ish back yard with close by transmitting antennas etc, my investment should ! Fit the bill nicely.I hope. Ken.. G0ORH