Re: [Elecraft] Beep

SW TONE won't silence it? >From page 65 of the KX3 Owner's manual: '... Switch press tones are enabled by default. Using the SW TONE menu entry, you can turn tones OFF, ON,..." 73, Ron AC7AC -Original Message- From: elecraft-boun...@mailman.qth.net

[Elecraft] [K2] On initial Power-up, '"INFO 201" Remains

Need some help here. Been working on my K2 S/N 7770 and got to the point where power is first applied. Upon pressing the Power button, got the INFO 201 message, but it just remained on the display. It never went away and I never saw the ‘7100.00c’. Turned power off and then cycled it back

Re: [Elecraft] Beep

Any hope of killing the beep? this is an old issue.since a lot of changes are in beta maybe this could be considered? In regard to the Elecraft Frequency Memory Editor: When using the QSY capability the KX3 does a beep. Even with the headphones plugged in, the speaker does a

[Elecraft] SignaLink USB has sold

SignaLink has sold. Thanks everyone. 73 George wb5xx Sent from my iPhone __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This

[Elecraft] FS- RemoteRig RRC -1258MkIIs

RemoteRig RRC -1258MkIIs with cables for K3/0 This is for the RRC Control Unit (has the CW control knob) $200 mailed Jack W4GRJ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

[Elecraft] FS:SignaLink USB F/K3/KX3

Never used. Including all cables. $90 shipped. Thanks. George wb5xx Sent from my iPhone __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

[Elecraft] DC insertion into antenna coax

I would be careful about running DC through the coax. Rapid rise and fall times of the DC voltage can generate RF spikes, and the collapse of the field in a DC relay if there is one at the business end can produce high instantaneous voltages back down to the rig end of the feedline. There

Re: [Elecraft] Using T1 with KX2 or KX3

Indeed, that has been done (also by me) and works fine. http://www.jtmiller.com/t1_tuner_project.html The only drawback by the insertion of a bias tee could be that the path for discharging static charges on the antenna is interrupted. 73, Heinz HB9BCB > Am 15.11.2017 um 19:42 schrieb Steve

Re: [Elecraft] Using T1 with KX2 or KX3

Hmmm. That means that it should be trivial to make a DC-blocking circuit that would allow you to pull the ring of J3 to DC (and not RF) ground over the coax to initiate tuning. Then you would have part of the remote control puzzle solved. That's nearly enough to finally get me to buy a T1. On

[Elecraft] P3 died...Is there one available in Reno, NV???

Just got off the phone with Elecraft and they gave me a RMA, but they don't have a P3 loaner available... I will be working the SS this weekend and I'm in need Is there anyone in the Reno area who will not be working the contest who has one with the SVGA card that I could borrow for the

Re: [Elecraft] Using T1 with KX2 or KX3

Understood. The T1 manual indicates that you can manually initiate tuning remotely by pulling the ring of J3 to ground, so running an extra control line from the operating position to the remote T1 could work. It also details the protocol for sending band info to the T1 to recall the previous

[Elecraft] : FS- SignaLink USB for K3 SOLD

SOLD Jack W4GRJ From: w4grj [mailto:w4...@satterfield.org] Sent: Wednesday, November 15, 2017 9:32 AM To: Elecraft@mailman.qth.net Subject: FS- SignaLink USB for K3 SignaLink USB forK3, includes K3 cables $85 mailed please email inquires offline w4...@arrl.net Jack W4GRJ

Re: [Elecraft] K3 / K3S Filters Available

Sorry, I did not mention the plots nor how many poles they are: You can see the current filter bandwidth plots at: http://www.elecraft.com/K3/K3_filter_plots.htm Of these, what I have available for the K3 or K3s are: Two each 2.7 kHZ 5 Pole filters; list 139.95 sell 100.00 each; (OEM SSB)

[Elecraft] FS- SignaLink USB for K3

SignaLink USB forK3, includes K3 cables $85 mailed please email inquires offline w4...@arrl.net Jack W4GRJ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

Re: [Elecraft] Using T1 with KX2 or KX3

Yes, different use case. All my KX's have the internal tuner. But I was thinking of an antenna configuration which would benefit from having a T1 mounted away from the operating position. 73, Barry N1EU On Wed, Nov 15, 2017 at 9:00 AM, Dave Fugleberg wrote: > Barry, I

Re: [Elecraft] Using T1 with KX2 or KX3

Barry, I went through that thought exercise before I ordered my KX2, since I already own a T1. In the end I ordered the internal tuner with the KX2. I have not regretted it for a minute. No extra cables, batteries, or fuss. And it works very well. Since you're concerned about remoting the tuner,

Re: [Elecraft] sharing K3 RS232 to CAT and Remoterig

On 11/14/2017 9:34 PM, Don Wilhelm wrote: > > Let me give you a concrete example of why 2 RS-232 ports cannot share > the same port. Not necessarily. One can successfully share a device like the K3 CAT port between two computers (or a computer and SteppIR controller, computer and Remote Rig

Re: [Elecraft] sharing K3 RS232 to CAT and Remoterig

Hello Joe thanks for the help. This will be an option, dont like too much to rewiring or reconfiguration thinks, dont have skills for that :-( BUT Mitch point me to a solution I need to try On remoterig manual http://www.remoterig.com/downloads/RemoteRig_RRC1258-MkII_Users_manual.pdf page 217

Re: [Elecraft] Using T1 with KX2 or KX3

It is correct understood, Barry. 73, Heinz HB9BCB > Am 15.11.2017 um 11:44 schrieb Barry N1EU : > > I'm looking for confirmation on how I understand the T1 would work with my > KX2 or KX3. When I change bands, I will need to go through a manual > re-tune process. The

[Elecraft] K3 P3 IF connection question

I have recently moved QTH and am now setting up my Elecraft radios in the new shack - in exactly the same configuration as at the previous QTH. No hardware changes, no firmware upgrades, same cable set. Everything is working fine with the K3/P3/KPA500/KAT500 combination, with one exception: The

[Elecraft] Using T1 with KX2 or KX3

I'm looking for confirmation on how I understand the T1 would work with my KX2 or KX3. When I change bands, I will need to go through a manual re-tune process. The memories in the T1 won't automatically recall a setting based on the newly transmitted frequency. In the case of the KX2 or KX3, I