Tnx Dick …. Sounds like that will work … I’ll take a close look at it …. The
big microHam cable assembly between MK2R+ and K3 is currently using the K3
straight key jack but I should be able to make a Y adapter to run both lines in
….
Don
Sent from Mail for Windows 10
From:
Please consider joining us for the weekly Elecraft SSB Net on Sundays at
18:00z (UTC) on 14.303.5. Note that for states that have Daylight Savings
Time the local time will change to an hour later, but the UTC time (18:00z)
remains the same.
Net control, Eric WB9JNZ, sends the report for this
Knut -
A friend got an IC-7610 and waited about ONE YEAR... they obviously did not
have thousands on the shelf when it was announced.
Dave - K9FN
On Wed, Mar 7, 2018 at 7:12 PM ab2tc wrote:
> Hi,
>
> Well, isn't this fairly typical behavior by Elecraft on a major new product
>
Just wondering if the low power K3S kit with extra filters etc is offered as a
special?
Seems they usually have the 100W factory combos.
Sent from my iPhone
__
Elecraft mailing list
Home:
You might run a cable from the KPA1500 back panel TUNE connector to the K3
straight key input. The KPA1500 pulls the tip of the connector low when it
needs to do an ATU tune (because you pressed the ATU TUNE button, or we're
doing an "swr-initiated" tune. I use a 3.5mm TRS plug to plug (the
I do miscellaneous switching chores at my remote station with two devices:
a remotely-controlled AC power strip and a remotely-controlled DC relay
board. Either could be adapted to your requirements IF your switch has
digital inputs such as four independent control lines. I don't know if
either of
Great, old photos are worth as much as the texts themselves!
I consider myself a bit of a "hobby-defined individual" and I've
participated in 26 of these activities at some level, and a few others in
passing. But ham radio surpasses them all! I'm also still active in SCUBA
diving, flying,
I’m just getting to know my new KPA1500 and am having a ball doing so …. it is
a gem!one minor problem: I’m using the key line interrupter in the Aux
cable since I am keying through a microHam MK2R+ (the K3S/KPA1500 is one of two
radios connected through the MK2R+ ….. so the key line must
Anyone have one of these they want to part with?
Please reply offline.
Dennis W1UE
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Thanks for all the quick replies from everyone,
I have secured a replacement board and am looking forward to getting the
K3 on the air.
Thanks again to all that replied.
Tom
Wa8WZG
__
Elecraft mailing list
Home:
Hi,
Well, isn't this fairly typical behavior by Elecraft on a major new product
introduction? Get used to it. Sure, Icom and the other big two probably have
thousands of units on the shelf when they make a product announcements, but
they have a different business model.
AB2TC - Knut
Hi Jim,
To All.
I am new to the list ,I just bought a "new to me" K3. I am having issues
with the rs 232 interface with it. I need to replace the KIO3 board. Is
there anybody out there that has moved up to the KIO3B kit, that may
have their old KIO3 board for sale.
Thanks in advance,
Tom
WA8WZG DM34
Hi Jim,
Not broken down by prepaid levels but they did say in the Early
Notification email this:
Deposit Preorders will be shipped from the first production run in the order
received, followed by non-deposit orders.
So I wasn't sitting at the computer when the announcement hit but
Torrey ... In my case, the notification email was sent at 7:15pm Thu 8/24/2017
MDT and confirmation of my order number 110356 was sent at 7:36pm Thu 8/24/2017
MDT (my number preceeds yours by only 8 and my confirmation
preceeded yours by 11 minutes) Other than the fact that
Hi,
I just received my KXPD2 and needed a case to protect it.
Couldn't find one so I created one to print in my 3D printer :-)
Thought I share it for anyone who find it useful:https://
www.youmagine.com/designs/kxpd2-case
73 de SM0XHJ
Stephen,
In DATA A, use the SHIFT (PBT II) to shift the passband down.
The widest passband is 3000 Hz. which is consistent with your 400 to
3500 Hz observation. I suggest shifting it to 150 to 3150 Hz. It will
work fine for most soundcard data modes.
The K3/K3S has the same behavior, but
I placed my order with a $1000 deposit on 8/31. I expect them to put those who
fully prepaid for their amplifiers first and those who put a $3000 deposit next
in line.
73, Jim N7US
-Original Message-
KPA1500 S/N 45 arrived at my Utah qth yesterday (Tuesday March 6) after
shipping
Don,
You have my full attention!
The "early notification email is "postmarked" at 8:28 pm CDT on August 24th.
My full prepayment receipt with confirmation # is time stamped at 8:47 pm CDT
on August 24th.
So, I have a fully paid order confirmed 19 minutes after the notification email
was sent.
1. I had fun.
2. I read the Guide before, during, and after the test.
3. I started to 20m and was confused. Partly because I was not
hearing the FOX and was seeing stations below 1K with "R-12" reports.
4. On 20m, it did not help that XE1GK was calling CQ on top of W1/KH7Z
+/- 1HZ
Hi Rob,
>From the Utility info on the web site:
X86-based Linux: GTK+ 2.8 or later, glibc-2.4, libstdc++.so.6 and cURL.
64-bit Linux requires 32-bit compatibility libraries.
If you do a search of the reflector archives you should be able to find a
list of the 32 bit libraries needed:
Great...good luck and have fun. I ordered Aug 30 so should have by the 4th
of July.
Richard
*W7ZR* ex:5C5Z, CN2ZR, K2JSP, W6SBZ, W7KXR, K9ZIJ, W9KNF, W0KDF, W0MQU,
J68ZR, KC6ZR, PJ4/W7ZR, KH2,W7ZR, KH6/W7ZR, V31ZR, VK4AAZ, XE2DV
*Be joyful in hope, patient in affliction, faithful in prayer*
Hi Dennis.
Have you checked what is available here:
http://www.remoterig.com/wp/
73, Yngvi TF3Y
On Wed, Mar 7, 2018 at 1:30 AM, Dennis Ashworth
wrote:
> My original post (below) morphed into a thread on standards, etc ... the
> discussion was insightful and useful
KPA1500 S/N 45 arrived at my Utah qth yesterday (Tuesday March 6) after
shipping on Friday March 2. For those of you who are closely watching
shipment progress and serial numbers, my prepaid order was placed on Aug 24 ten
minutes after the “now accepting orders” email had been sent …… and the
The T.O. Keyer has been sold. Thanks for the replies.
Gus Hansen
KB0YH
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This
Whoa, a Linux question? Excellent.
Looks the HarfBuzz shared libraries got updated (probably along with your
window manager of choice) and the kx3util needs to be rebuilt (relinked?
Not certain of the proper dev-speak here) to reference the newer
libraries. (Sorry if I'm preaching to the
Looking in dmesg, I found this:
[ 3817.471455] traps: kx3util[7873] general protection ip:f6771298
sp:ffb24f08 error:0 in libharfbuzz.so.0.10705.0[f6742000+ae000]
On Tue, Mar 6, 2018 at 7:42 PM, Robert Felmey wrote:
> Hi,
>
> Seems like there is a problem with the KX3 Utility
No one ever got fired for specifying AMP products. (now TE)
https://www.mouser.com/pdfdocs/ENG_DS_82042_StdTermsSplices_0708.pdf
de AJ4TF
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home:
27 matches
Mail list logo