No
Bias is independent as to front/rear connections.
I use my headset w/bias (CM500) on rear and my Heil HM12 dynamic mic on from
without bias in front jack.
Sent from my iPhone
...nr4c. bill
> On Mar 15, 2018, at 9:33 PM, Bob Harvey - K2PI wrote:
>
> When using a
I used my K2 as a VFO for a Drake 2NT boat anchor transmitter for quite
awhile. Worked great while I worked on a real one that fit the character
of boat anchors better--the K2 version was lacking sufficient drift and
chirp to be convincing. I modified a Siltronix (Swan) CB VFO to fit the
bill.
Harv,
If you have the Rear Panel bias set on, and the Front Panel bias set on,
all you have to do is change MIC SEL fron the front panel to the rear panel.
In other words, no problem.
73,
Don W3FPR
On 3/15/2018 9:33 PM, Bob Harvey - K2PI wrote:
When using a rear panel headset requiring
When using a rear panel headset requiring Bias, what is the state of Bias on
the Front Panel mic connector?
I have a PR-781 Microphone that doesn't require bias, and have it
disconnected from the front panel when using the rear bias'd mic and the RP
bias setting in the menu. Do I need to do
Oh WOW ~ I like the article by Wayne, N6KR*/Extreme QRPp using the KX2,
KX3, K3, or K3S/*
Via this technique I (we) can use the "unit" as a Signal Generator . . .
. as I'm in need of "that" just now, while troubleshooting my Genesis
G59 MKIII sdr transceiver kit
Thanks Wayne !
Cheers, Jan
There has been very low humidity this week, and I have had some shocks at
home.
When we got lots of static discharge shocks after walking on my
mother-in-law's carpet, I put some 1 Meg Ohm resistors under the light
switch cover screw for her to touch in the winter before the switch. Silly
idea
Try a humidifier to reduce the static.
Sent from my iPhone
...nr4c. bill
> On Mar 15, 2018, at 11:08 AM, Chuck Milam, N9KY wrote:
>
> Greetings, All!
>
> I'm getting static electricity shocks through my K-Pod case, and I need
> some suggestions for mitigation.
>
>
All!
Sent from my iPhone
...nr4c. bill
> On Mar 15, 2018, at 1:15 PM, Wes Stewart wrote:
>
> Your message or his?
>
>> On 3/15/2018 8:14 AM, w4grj wrote:
>> What a waste of bandwidthJackW4GRJ
>>
>
> __
>
Warning! Until that dries, it could be very slippery!
On Thu, 15 Mar 2018, Bob McGraw K4TAX wrote:
Mix a solution of 1 part DOWNY fabric softener and 1 part water. Put it
in a spray bottle and mist the carpet. You may need to mist the plastic
chair pad as well. This should take care of the
I guess "3-4 weeks" has become "2-3 weeks" (since 5 weeks ago). so
maybe if we substitute "months" for "weeks" we'll get something more
realistic :/
I still think that each time-relative statement on that page should
include an individual timestamp.
73,
~iain / N6ML
On Thu, Mar 15,
That was was the status on Feb 6th, though:
http://elecraft.365791.n2.nabble.com/KPA1500-ordered-8-24-td7638005.html#a7638028
So I'm failing to see an update
73,
~iain / N6ML
On Thu, Mar 15, 2018 at 1:39 PM, Dennis Moore wrote:
> There is a date at the top of
There is a date at the top of the page, March 15th. So I would preface
the "Due to very large rush..." with "As of March 15th, ..)
73, Dennis NJ6G
On 3/15/2018 12:59, iain macdonnell - N6ML wrote:
It doesn't look updated to me, though. It might also be good if
statements like "Due to very
Ugh! I hope you didn't blow anything by shorting pins together with
the shield of the USB plug!
73,
~iain / N6ML
On Thu, Mar 15, 2018 at 1:18 PM, Michael Blake wrote:
> I am not sure how many of you have noticed the warnings in the K3s and P3
> manual to NOT plug a USB B
I am not sure how many of you have noticed the warnings in the K3s and P3
manual to NOT plug a USB B connector into the 8P8C modular jack lableled
“RS232/P3” on the rear of the K3s. This is a VERY important warning but only
if you read it prior to inserting the USB cable (twice) into the
On Thu, Mar 15, 2018 at 12:54 PM, Eric Swartz - WA6HHQ, Elecraft
wrote:
> Aargh :-) You are correct! My typo..
:) It doesn't look updated to me, though. It might also be good if
statements like "Due to very large rush of orders we received on 8/24,
we expect to continue
*KPA1500s are Shipping!*
*We are still shipping orders from August 24th, the first day we began
taking orders. *Due to very large rush of orders we received on 8/24, we
expect to continue shipping those orders over the next 2-3 weeks.
/Its been a lot of hard work getting the KPA1500 released
Aargh :-) You are correct! My typo..
Thanks for the correction.
73,
Eric
/elecraft.com/
On 3/15/2018 12:52 PM, iain macdonnell - N6ML wrote:
Or http://www.elecraft.com/elecraft_shipping_status.htm
73,
~iain / N6ML
__
Or http://www.elecraft.com/elecraft_shipping_status.htm
73,
~iain / N6ML
On Thu, Mar 15, 2018 at 12:49 PM, Eric Swartz - WA6HHQ, Elecraft
wrote:
> We are working hard and have just updated the KPA1500 shipping status as of
> today 3/15.
>
> see:
We are working hard and have just updated the KPA1500 shipping status as of
today 3/15.
see: http://elecraft.com/shipping_status.htm
73,
Eric
/elecraft.com/
On 3/15/2018 11:06 AM, Rick WA6NHC wrote:
It appears that they are still working on the first day orders, which I'm sure
that day
Just a friendly reminder - making personal criticisms other's email postings to
the list, or follow on snide comments by others, just generate unneeded noise on
the list, are clearly outside of the list guidelines, and are not acceptable.
(The delete key is always available if you do not like
Mix a solution of 1 part DOWNY fabric softener and 1 part water. Put it
in a spray bottle and mist the carpet. You may need to mist the plastic
chair pad as well. This should take care of the static issue for quite
some time. If it returns, mist it again.
73
Bob, K4TAX
On 3/15/2018
The real issue here is the lack of household humidity. A humidifier is
probably in the real fix. Several hours of a near-boiling pan of water on
the kitchen stove would likely be enlightening.
Or, get a "real' anti-static (desk size) work mat with wrist strap. I have
one permanently atop my
Chuck,
I'm also in an area of low humidity and such static discharges
are a problem. I have everything grounded together and a small
patch of aluminum foil connected with a 1 megohn resistor. After
a trip across the carpet and before touching anything, I touch the
foil. The resistor prevents
Chuck,
I had this problem in my carpeted shack with a desk chair rolling around
on a vinyl chair pad. After a little testing I determined that the metal
case of the K-Pod is not grounded.
The KPod uses a straight-through 6 conductor cable with identical RJ
connectors on each end. I built a
It appears that they are still working on the first day orders, which
I'm sure that day alone was massive. Mine was confirmed (paid) at 12:54
PM 24 Aug 17 and I've had no notice yet.
Patience, is required.
Rick NHC
On 3/15/2018 10:52 AM, Paul Van Dyke wrote:
The KPA1500 will be on your
Greetings, All!
I'm getting static electricity shocks through my K-Pod case, and I need
some suggestions for mitigation.
Background: I keep my K-Pod on my operating desk just to the right of the
shack computer mouse. I've noticed when I walk over to the desk and grab
the mouse, the K-Pod will
The KPA1500 will be on your door step as fast as they can ship them. IF I
remember, it was going to take a few weeks just to get thru the 1st days
orders.
Paul. KB9AVO
Waiting also . But it will get to me .. Not worried
On Mar 15, 2018 12:17 PM, "Wes Stewart" wrote:
>
Your message or his?
On 3/15/2018 8:14 AM, w4grj wrote:
What a waste of bandwidthJackW4GRJ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Tom,
A long hold of the menu button will put the K3 into terminal mode, then one can
control another with an RS232 cable.
Carl
AB1DD
From: elecraft-boun...@mailman.qth.net on
behalf of Tom Georgens
Hello
I am contemplating building some remote capability for my station. I am
early in the process and want to do some basic testing. Can I just connect
two K3 radios with a Null Modem serial cable or do I actually need the
RemoteRig hardware to make the remote functionality work? It looks
I’m wondering how much worse the problem will be as DirecTV goes to this new
technology that’s being advertised on TV-something about a wireless receiver.
I’ll have to pay more attention. It sounds like something that the girlfriend
may want to wait for. Right now her equipment is
You are, of course, absolutely correct Jim. Know that one model of the sat
receiver uses an RF remote of some sort that many think is the culprit.
Sadly the response from the, understandably RF clueless, sat help lines is
kind of like going to a doctor with the plea "it hurts to do this" and
What a waste of bandwidthJackW4GRJ
Sent from my T-Mobile 4G LTE Device
Original message From: Richard Thorne
Date: 3/15/18 10:56 (GMT-05:00) To: Elecraft Reflector
Subject: [Elecraft] KPA-1500 Deliver Update
Any updates on
Any updates on delivery time? Last one was posted on 02/20.
Thanks
Rich - N5ZC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
I use two different RX antennas in diversity. I have a selection of 7
Beverages on Main and 4 direction switchable Hi-Z RX4SQ on Sub. If I want
to listen on my TX antenna (which is occasionally best), I toggle RX ANT to
switch from the Beverages to TX ANT. If the RX4SQ is not contributing to
35 matches
Mail list logo