Re: [Elecraft] Ideas for an FT8 Radio

They can put it on a separate module. There's space for at least a Raspberry Pi Zero in there, so it could be put on a dedicated board of its own. That way, it wouldn't be software in the main system firmware, it'd be a separate, optional module with its own license. THAT can be GPL. You can sell

Re: [Elecraft] Ideas for an FT8 Radio

As long as the developer is using any part of the WSJT-X code it cannot be added to closed source firmware.    It doesn't matter that it can be done. It would be in violation of the GPL Neil, KN3ILZ On 12/30/2018 8:59 PM, John Harper wrote: Here's the thread - scroll down to message #27527:

[Elecraft] Happy New Year!

Ken and I want to wish all you Elecraft folks a very happy and prosperous new year. 88 / 73 ! Rose (N7HKW) and Ken (K0PP) __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

Re: [Elecraft] Happy New Year from Germany

Well, we are all getting older and hopefully wiser, hi.  Got mine in 1957. ALWAYS the best effort I ever did, except the XYL of course...  Cheers, from the west coast. Mel, K6KBE From: Doug Turnbull To: 'Bob DeHaney' ; elecraft@mailman.qth.net Sent: Monday, December 31, 2018 3:59 PM

Re: [Elecraft] Ideas for an FT8 Radio

That explains the complete and utter failure of the K1 and KX1 to gain any popularity. 73, Dennis NJ6G Happy New Year! On 12/30/2018 17:56, Devin Butterfield wrote: I also agree that a one-mode radio wouldn’t be of interest for very long. — Regards, Devin / K6DRS

Re: [Elecraft] Happy New Year from Germany

Good Man Bob. I also so add HNY to all our fellows and sisters.We are licensed in the same year. My ticket arrived one week after turning 16 and was the best present.So guess I am but a pup but yes it is great to wake up each morning. We share a great hobby for both youth and when

[Elecraft] Happy New Year from Germany

Vy 73 de Bob DJ0RD/WU5T who will be 79 this month, still a Ham since 1960. Yes, I am happy when I wake up in the morning  __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

Re: [Elecraft] KAT500/KPA500 with Icom 7600 accessory cable

Hi Ken, If you haven't seen them, these may be a help to you. http://www.ke7x.com/home/k-line-introduction-and-set-up-guide Cheers and 73, Fred KE7X For all KE7X Elecraft books and the new "Successful Ham Radio Operator's Handbook", see www.ke7x.com

Re: [Elecraft] KAT500/KPA500 with Icom 7600 accessory cable

Ken, If that Send cable is the only one you have connected between your Icom and the KAT500, you need to feed a bit of RF to initiate a TUNE The KAT500 will first look for a saved L/C combination for that antenna and frequency and will switch to that rather than doing a TUNE.  Secondly, it

[Elecraft] 2019

Happy New Year to Elecraft staff and all of The Elecrafters. -- 73 Penna, OH2G, OH2CG K3 S7N 3791 & KX3 S7N 6624 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm

Re: [Elecraft] KPA1500 problem

Roy, The very first thing you do is attach a dummy load to the antenna jack on the back of he amp and isolate the problem to the amp or feedline and/or antenna.  If you don't have one, you should purchase one right away. I have seen the type of fault many times, and a good percentage of the it

Re: [Elecraft] KPA1500 problem

" My KPA1500 (s/n 121) has developed a problem: When applying power (15-20W) from the K3 to the amp, it immediately faults to:low gain fault ratio 3 (sometimes ratio 2 to ratio 6). The SWR indicator shows high SWR as the amp faults. 100w only from exciter will cause ATU to tune to 1:1 but

Re: [Elecraft] KAT500/KPA500 with Icom 7600 accessory cable

Thank you Jack Sorry for the delay was helping to prepare for todays town wide charity dinner, where we typically feed 4-500 people Will check when I get back home later today.   From: Jack Brindle To: Ken B Cc: "elecraft@mailman.qth.net" Sent: Sunday, December 30, 2018 9:53 PM