[Elecraft] P3SVGA Wanted

2022-06-01 Thread Bud Governale
I'm looking to purchase a P3SVGA. Please let me know if you have one you'd like to sell. 73, Bud W3LL w...@arrl.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm

[Elecraft] K3 Jumps To High Output In Data Mode During Power Knob Rotation

2017-09-03 Thread Bud Governale, W3LL
The K3 mode button is set to DATA and the transmit mode is DATA A. As I adjust the power output (PWR) knob during continuous transmit, the measured output displayed on the Power Master jumps to a high level. As an experiment, If the output is at a steady 40 W for example, when I slowly and

[Elecraft] P3 Showing Transmit Signal

2015-11-24 Thread Bud Governale
I noticed this weekend that occasionally during transmit instead of the scan freezing in place it would continue scanning showing only my transmit signal with only that signal appearing in the black waterfall. I don't have the P3TXMON. It never did this before. I was viewing the external SVGA

[Elecraft] P3 Freeze

2015-03-02 Thread Bud Governale
Has a non Beta firmware update been released which minimizes the time for the SVGA display to unfreeze between CQ’s during a contest? This made it difficult to find/observe a clear channel in the waterfall between CQ’s or contacts. 73, Bud W3LL w...@arrl.net

[Elecraft] K3 No Transmit When WAV File Is Played

2014-12-11 Thread Bud Governale
When I hit a function key in N1MM the correct wav file plays as heard thru the computer speakers. However the K3 (in SSB mode) does not transmit. Any suggestions? 73, Bud W3LL w...@arrl.net __ Elecraft mailing list Home:

[Elecraft] P3 No Longer Matching K3 Signal Level

2014-04-01 Thread Bud Governale
My P3 always matched S meter signal level to the K3. This morning with the S0 on the K3 ( with antenna disconnected) the P3 is displaying a level about 7 db below the S0 level. With antenna connected the K3 shows S7 while the P3 level on the screen is slightly below S0. What happened and how

[Elecraft] P3 Not Showing Sub Receiver Cursor When Not In Split Mode

2013-12-06 Thread Bud Governale
P3:If I turn on Split I see the sub receiver cursor along with VFO A. However if I just turn on the sub receiver without Split I only see VFO A. I need to see VFO B when tuning VFO B when not in Split Mode. How do I do this? 73, Bud W3LL w...@arrl.net

[Elecraft] P3 SteppIR Connection

2013-10-13 Thread Bud Governale
On what RS232 leg should I connect the SteppIR controller? P3 to K3 Leg or P3 to Computer. I think one leg may carry less traffic. 73, Bud W3LL __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

[Elecraft] K3 Low Audio Output on 2M FM

2013-10-13 Thread Bud Governale
I used for the first time the FM mode on 2M during an EOC Area Exercise this weekend. The K3 has the internal 2M transverter along with a 13 KHz FM filter in the main radio (VFO A) All were having much difficulty with my transmissions due to low audio output. RF out was not the issue with

[Elecraft] K3 PSK-D Split Operation

2012-01-05 Thread Bud Governale, W3LL
When in Data Mode PSK-D (31 bps) I get SPL N/A when trying to operate split. Both VFO's were on the same frequency but could not get VFO B to go up. What do I need to do to go into split operation in this mode? Today VK0TH was operating on 28,121 MHz and listening 400 Hz up. I just could not

Re: [Elecraft] K3 Edgeport Adapter with K3 and SteppIR

2010-04-01 Thread Bud Governale, W3LL
converter. Thanks! 73, Bud W3LL w...@arrl.net - Original Message - From: Joe Subich, W4TV li...@subich.com To: 'Bud Governale, W3LL' w...@arrl.net Sent: Tuesday, March 30, 2010 12:38 PM Subject: RE: [Elecraft] K3 Edgeport Adapter with K3 and SteppIR My K3 serial number is 2285. Not sure

[Elecraft] K3 Edgeport Adapter with K3 and SteppIR

2010-03-29 Thread Bud Governale, W3LL
I have my K3 and SteppIR controller talking perfectly thru the computer logging program and Y cable using a Prolific USB to Serial converter cable. I purchased an Edgeport 8 USB to Serial converter and removed all the Prolific cables to existing devices and connected all directly to the

[Elecraft] K3 Audio/RFI Feedback

2010-01-19 Thread Bud Governale, W3LL
I'm experiencing audio/RFI feedback on 80M between the frequencies of 3650 KHz to 3850 KHz using a full-size 80M vertical 100' from the radio. SWR is under 2:1. No difference if I use the built-in ATU. If I key the K3 and tap the mic once it goes into motorboating with full output (100W). The

[Elecraft] K3 Sub Receiver forces FSK D to AFSK A

2009-11-12 Thread Bud Governale, W3LL
I've always used FSK D mode. Since updating to 3.57 when I turn on the Sub Receiver the radio goes into AFSK A. How do I stop the SUB from changing FSK D to AFSK A? In the past the radio was always in FSK D and the SUB did not change this. I'm in VFO A and check DATA MD. It says FSK D. Turn

[Elecraft] K3 No Sub Audio In Right Speaker

2009-10-01 Thread Bud Governale, W3LL
How can I have the sub receiver audio play from the right speaker along with the main receiver playing in the left speaker? I have no sub receiver audio from the right speaker. I do have audio from the main receiver in the left speaker. Using headphones, I have main in left ear and sub in right

[Elecraft] PSK-D Mode

2009-08-10 Thread Bud Governale, W3LL
I made a few PSK31 QSO's today sending in DATA-A mode. However, I like the apparent benefit to PSK-D mode where there is no need to watch ALC levels. I use FSK-D for RTTY which works very well with no need to watch audio levels. In PSK-D, I can Key and send PSK. In the monitor I hear what

[Elecraft] K3 Main Radio plays in Left External Speaker Only

2009-05-18 Thread Bud Governale, W3LL
How can I get the main receiver to play from both L R external computer speakers? The main receiver plays in only the left external computer speakers. Using firmware 3.11. K3 audio output is connected to the soundcard input. Soundcard output feeds both the computer and auxiliary speaker

[Elecraft] K3 ERR KEY - Continuous Keying

2009-04-09 Thread Bud Governale, W3LL
My K3 display shows ERR KEY when I turn it on. It's been working flawlessly until now and no recent changes have been made. 1.No programs are running on the computer. ERR Key is displayed on the K3 2.If I shut down the computer the ERR Key turns off partway thru the Windows is Shutting

[Elecraft] K3 FSK Passband Frequency

2009-03-26 Thread Bud Governale, W3LL
I'm using FSK-D. To tune in an FSK signal I need to use Shift to shift the signal to the right of the passband display on the K3 (centered over the right side arrow). This then places the signal in the center of the MTTY display. However, received signals are now about 0.55 KHz higher than

Re: [Elecraft] K3 FSK Passband Frequency

2009-03-26 Thread Bud Governale, W3LL
Hi Ken, Thanks!!! That did it. All is OK now. 73, Bud W3LL - Original Message - From: Ken K3IU To: Bud Governale, W3LL Cc: Elecraft Reflector Sent: Thursday, March 26, 2009 2:55 PM Subject: Re: [Elecraft] K3 FSK Passband Frequency Hi Bud: If you make sure

[Elecraft] K3 Transmit thru Line-In

2009-03-05 Thread Bud Governale, W3LL
I can't get any transmit audio via the Line-In connector. Connecting the Mic cable to the rear panel MIC connection produces good transmit power and audio. I know audio is coming from the sound card output because it also drives the computer speaker via its line in connection. I tried moving

[Elecraft] MIC + Line-In Feedback Noise

2009-03-05 Thread Bud Governale, W3LL
Thanks to both Eric K3NA and Rich VE3KI, I now have Line-In working. That leads to a new related issue: When MIC + LIN is turned ON I get feedback from somewhere when I key with the foot switch in SSB without saying anything. If I turn MIC + LIN to OFF the feedback is gone. I closed N1MM just

[Elecraft] K3 Line-In Mono

2009-01-10 Thread Bud Governale, W3LL
The manual says K3 Line-In is connected to the PC soundcard output using a Mono connector. My PC sound card line output is a stereo connection. It also connects via stereo splitters to PC amplified speakers and other stereo line inputs using stereo connectors. Can I use a stereo connector to

[Elecraft] K3 Accessory Connector

2008-09-17 Thread Bud Governale, W3LL
When breaking out K3 Accessory Connector leads to RCA jacks, do all return connections for PTT, Key Out, ALC, +12Vin, Power On, Digiout0 and Digiout1 go to either pins 5 or 12? Bud W3LL [EMAIL PROTECTED] ___ Elecraft mailing list Post to:

[Elecraft] K3 Transverter Control Cable

2008-06-24 Thread Bud Governale, W3LL
I'd like to make up a K3 Transverter control cable. Which pins of the Elecraft Transverter J6 DB-9 connector are connected to which pins of the K3 AUX I/O? Bud W3LL [EMAIL PROTECTED] ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You