[Elecraft] K3 Jumps To High Output In Data Mode During Power Knob Rotation

The K3 mode button is set to DATA and the transmit mode is DATA A. As I adjust the power output (PWR) knob during continuous transmit, the measured output displayed on the Power Master jumps to a high level. As an experiment, If the output is at a steady 40 W for example, when I slowly and

[Elecraft] K3 PSK-D Split Operation

When in Data Mode PSK-D (31 bps) I get SPL N/A when trying to operate split. Both VFO's were on the same frequency but could not get VFO B to go up. What do I need to do to go into split operation in this mode? Today VK0TH was operating on 28,121 MHz and listening 400 Hz up. I just could not

Re: [Elecraft] K3 Edgeport Adapter with K3 and SteppIR

converter. Thanks! 73, Bud W3LL w...@arrl.net - Original Message - From: Joe Subich, W4TV li...@subich.com To: 'Bud Governale, W3LL' w...@arrl.net Sent: Tuesday, March 30, 2010 12:38 PM Subject: RE: [Elecraft] K3 Edgeport Adapter with K3 and SteppIR My K3 serial number is 2285. Not sure

[Elecraft] K3 Edgeport Adapter with K3 and SteppIR

I have my K3 and SteppIR controller talking perfectly thru the computer logging program and Y cable using a Prolific USB to Serial converter cable. I purchased an Edgeport 8 USB to Serial converter and removed all the Prolific cables to existing devices and connected all directly to the

[Elecraft] K3 Audio/RFI Feedback

I'm experiencing audio/RFI feedback on 80M between the frequencies of 3650 KHz to 3850 KHz using a full-size 80M vertical 100' from the radio. SWR is under 2:1. No difference if I use the built-in ATU. If I key the K3 and tap the mic once it goes into motorboating with full output (100W). The

[Elecraft] K3 Sub Receiver forces FSK D to AFSK A

I've always used FSK D mode. Since updating to 3.57 when I turn on the Sub Receiver the radio goes into AFSK A. How do I stop the SUB from changing FSK D to AFSK A? In the past the radio was always in FSK D and the SUB did not change this. I'm in VFO A and check DATA MD. It says FSK D. Turn

[Elecraft] K3 No Sub Audio In Right Speaker

How can I have the sub receiver audio play from the right speaker along with the main receiver playing in the left speaker? I have no sub receiver audio from the right speaker. I do have audio from the main receiver in the left speaker. Using headphones, I have main in left ear and sub in right

[Elecraft] PSK-D Mode

I made a few PSK31 QSO's today sending in DATA-A mode. However, I like the apparent benefit to PSK-D mode where there is no need to watch ALC levels. I use FSK-D for RTTY which works very well with no need to watch audio levels. In PSK-D, I can Key and send PSK. In the monitor I hear what

[Elecraft] K3 Main Radio plays in Left External Speaker Only

How can I get the main receiver to play from both L R external computer speakers? The main receiver plays in only the left external computer speakers. Using firmware 3.11. K3 audio output is connected to the soundcard input. Soundcard output feeds both the computer and auxiliary speaker

[Elecraft] K3 ERR KEY - Continuous Keying

My K3 display shows ERR KEY when I turn it on. It's been working flawlessly until now and no recent changes have been made. 1.No programs are running on the computer. ERR Key is displayed on the K3 2.If I shut down the computer the ERR Key turns off partway thru the Windows is Shutting

[Elecraft] K3 FSK Passband Frequency

I'm using FSK-D. To tune in an FSK signal I need to use Shift to shift the signal to the right of the passband display on the K3 (centered over the right side arrow). This then places the signal in the center of the MTTY display. However, received signals are now about 0.55 KHz higher than

Re: [Elecraft] K3 FSK Passband Frequency

Hi Ken, Thanks!!! That did it. All is OK now. 73, Bud W3LL - Original Message - From: Ken K3IU To: Bud Governale, W3LL Cc: Elecraft Reflector Sent: Thursday, March 26, 2009 2:55 PM Subject: Re: [Elecraft] K3 FSK Passband Frequency Hi Bud: If you make sure

[Elecraft] K3 Transmit thru Line-In

I can't get any transmit audio via the Line-In connector. Connecting the Mic cable to the rear panel MIC connection produces good transmit power and audio. I know audio is coming from the sound card output because it also drives the computer speaker via its line in connection. I tried moving

[Elecraft] MIC + Line-In Feedback Noise

Thanks to both Eric K3NA and Rich VE3KI, I now have Line-In working. That leads to a new related issue: When MIC + LIN is turned ON I get feedback from somewhere when I key with the foot switch in SSB without saying anything. If I turn MIC + LIN to OFF the feedback is gone. I closed N1MM just

[Elecraft] K3 Line-In Mono

The manual says K3 Line-In is connected to the PC soundcard output using a Mono connector. My PC sound card line output is a stereo connection. It also connects via stereo splitters to PC amplified speakers and other stereo line inputs using stereo connectors. Can I use a stereo connector to

[Elecraft] K3 Accessory Connector

When breaking out K3 Accessory Connector leads to RCA jacks, do all return connections for PTT, Key Out, ALC, +12Vin, Power On, Digiout0 and Digiout1 go to either pins 5 or 12? Bud W3LL [EMAIL PROTECTED] ___ Elecraft mailing list Post to:

[Elecraft] K3 Transverter Control Cable

I'd like to make up a K3 Transverter control cable. Which pins of the Elecraft Transverter J6 DB-9 connector are connected to which pins of the K3 AUX I/O? Bud W3LL [EMAIL PROTECTED] ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You