Do NOT have power control with KPA100, have power control with base K2
Diode voltage drop values using my DMM's diode test function (fwd/rev bias):
D16 .246/.278
D17 .151/.160
with diodes in place.
73,
Casey
On Thu, November 9, 2017 6:50 pm, Don Wilhelm wrote:
> In normal operation you can
test
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email
I have for sale my K1-2 w/KAT1 and backlight mod, all works as it
should and is in mint condition short of a small scratch on the tuning
knob. Used it twice from my desk, needs a good home where it will get
used. Have all manuals etc.
serial no 02044
Pics available on request, would like $350
Don,
8T line is fine, zero volts.
Enc A voltage varies with turn of the encoder (approx. 5-.3V), but Enc B
does not (.09-.11V).
How can I get to the menu settings without a working encoder?
73,
Casey
On 12/29/2011 4:15 PM, Don Wilhelm wrote:
K2 A to B Instructions
, it doesn't release the rig from mute/PTT, whatever state
it's in. I put the cable back on the desktop and all works there OK.
Haven't had time to take stuff down to the bench to check voltages yet.
73,
Casey
On 7/3/2010 1:29 PM, Mike wrote:
No comfort for you, but my USB to serial
chip
and I have read that for CAT people have better luck with an FTDI based
converter. What is the difference between the chips that makes FTDI
better?
73,
Casey
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
Hi All,
I didn't see in the K2 spec what the TX audio response is, but I assume
it tops out at 3KHz.
Has anyone seen a K2 mod to widen this range, to, say, 4KHz or higher?
73,
Casey, NA7U
__
Elecraft mailing list
Home: http
Hi gang,
This document on the Elecraft web site,
http://bit.ly/solderingtips
says,
[Soldering iron] tip width will normally be in the range of 1/32 (0.79mm)
through 1/8 (3.2mm), depending upon the width of the pad to which you are
soldering. The width of the tip selected should be about 75% to
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
stand, and manuals. In near perfect condition, covers
20/40 meters. $375 plus shipping via Paypal only. Tnx! - Casey, NA7U
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
Hi gang,
As part of my continuing effort to gather the funds
for a new K3, I now have for sale an Oak Hills
Research OHR 100A 40 meter, 5 watt CW transceiver that
works properly, is in mint condition, and comes with
the manual and fused power cord. Note that the 100A
has both RF and AF gain
Hi gang,
Someone who is registered with Wikipedia should add
the Elecraft K3 to this list:
http://en.wikipedia.org/wiki/K3
Thanks 73,
Jeff
NE2J (formerly WB5GWB)
http://www.qsl.net/liqrp
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
Hi gang,
I have for sale a QRP K2 with all available options
installed (except the 100 watt PA). It includes the
KSB2, K160RX, K60XV, KNB2, KDSP2, KAT2, KIO2, KBT2,
Heil hand microphone purchased from Elecraft, and all
manuals. The serial number is 0821. However, all of
the upgrades
Hi gang,
I have a perfectly functioning KAF2 Audio Filter for
the K2 that I am willing to sell for $60 to be paid by
U.S. Postal Service Money Order, and I'll pay for
shipping within the U.S. or Canada.
If you're interested, please email me at [EMAIL PROTECTED]
Thanks very much 73,
Jeff, NE2J
I neglected to mention that the KAF2 I have for sale
was checked out and aligned by Don Wilhelm, W3FPR, in
Feb. 2006.
--- Jeff T. Casey [EMAIL PROTECTED] wrote:
Hi gang,
I have a perfectly functioning KAF2 Audio Filter for
the K2 that I am willing to sell for $60 to be paid
by
U.S. Postal
be placed on the
component side of the board or the bottom side of the board. It may not
matter, but no sense finding out the hard way that it does.
Thanks,
Mike Casey
KC9ORD
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must
Is there a standard setup for the paddles with a keyer? I've just
finished building a KX1 and I have a K2 and with both of these the keyer
is set up to send dahs with the left paddle and dits with the right
paddle. Yet if the bug was the precursor of the present day keyer it
seems that the
20 matches
Mail list logo