[Elecraft] KXIBC2 KX2 internal battery charger

Anyone know when the battery charger will ship its second round. Dlittle, AF5U __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net

[Elecraft] KX2 feedback CW

When I depress any selection on my KX2 - I get CW telling me what selection I pressed. How do I stop or restart this? I can’t kind it in the manual. Dave Little, AF5U __ Elecraft mailing list Home:

Re: [Elecraft] Are you satisfied with your K3?

And to elaborate on this theme, it is my setup on QTH up for trade. It is equal in price with a new FTDX-5000MP, and I am asking for the value of a used MP for it. Separately, I have tried to sell it for what used MPs are going for. I had tried to sell it for that price previously on QTH,

[Elecraft] FT: K3-F / P3-F Setup

Loaded K3/100 with P3 Pan adapter K3/100-F_Serial Number 50xx KAT-3F___100 Watt Auto Tuner (internal) KRX3-F___2nd RX KBPF3General Coverage RX Module KDVR3Digital Voice Recorder KTCXO3-1_TCXO (0.5 ppm) KXV3ARX Antenna, IF Out and Xverter Interface

Re: [Elecraft] K-Line system integration questions

FWIW, you can find InsideOut Edgeport interfaces on eBay that are usually quite reasonable. I have them in 2 port, 4 port and 8 port configurations. The use a single USB connector and provide what the computer sees as stable serial ports that stay where you put them. Each port can be

Re: [Elecraft] K3 Problems

Chas, If a single button held in on power up won't cure it, grab a handful. The CPU should still be attempting to strobe the panel for key presses. All you want it to do is have the lockup clear up long enough for the cpu to sense a correctable failure. If/When you get it unlocked;

Re: [Elecraft] Dumb Question

Hold the 1 button on the keypad for one second to toggle :b Set David KD4NUE -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of kis...@me.com Sent: Friday, November 16, 2012 1:49 PM To: elecraft@mailman.qth.net Subject:

[Elecraft] Swap K3FL3A-6K for KFL3B-FM

I have AM filters in both main and sub receivers, and would like to have the capability to work FM on 10m. Is there anyone out there that has 2 of the 8-pole FM filters and would like to swap for one an AM 8 -pole filter? respond to kd4nue at arrl dot net Thanks, David KD4NUE

[Elecraft] Swap AM filter for FM filter

On my previous message, I referenced 8 pole AM and FM filters, and I am not sure such exists. Let me reword it to want to trade an AM filter for a FM filter. David KD4NUE __ Elecraft mailing list Home:

Re: [Elecraft] Small HF amp suggestions

Take a look at this site: http://www.n2ckh.com/fl110.htm These show up from time to time. My little QRP circle of friends have found 2 in the last month. Both were around $300. When you see a solid state amp that was built in the late 70's with the original output transistors, you get the

[Elecraft] FS/FT: K3-F / P3-F

Loaded K3/100 with P3 Pan adapter K3/100-F_Serial Number 50xx KAT-3F___100 Watt Auto Tuner (internal) KRX3-F___2nd RX KBPF3General Coverage RX Module KDVR3Digital Voice Recorder KTCXO3-1_TCXO (0.5 ppm) KXV3ARX Antenna, IF Out and Xverter Interface

[Elecraft] K3 Receive Sensitivity Consistency

When I turned the K3 on this morning, I decided to listen to 60m, to get away from the contesting. As I went through the bands from the 2 meg frequency I had been monitoring, when it got to the 5 MHz band it seemed to be a bit deaf. Volume was considerably lower, but signal on the P3 looked

Re: [Elecraft] K3 Receive Sensitivity Consistency

Preamp, Attenuator, ATU, AGC were all checked before determining that the audio on 60m was lacking. The levels on the P3 were also checked to aid in determining the problem. RX EQ was all maxed out in able to overcome the inherit audio attenuation when the EQ settings are moved off of +16.

Re: [Elecraft] K3-PR10

10m preamp - TBA David KD4NUE -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of N5GE Sent: Thursday, October 25, 2012 2:04 PM To: Nand Kishore Cc: elecraft Subject: Re: [Elecraft] K3-PR10 I don't see that on the Elecraft

Re: [Elecraft] KPA500 input SWR in standby ...a question.

FWIW, below are my notes - from before I sent mine in for repair. Something happened that caused an LDG AT-1000Pro to toast the protection Diode, and an Icom IC-756 Pro 2 to burn one of the contacts off of the antenna 1 / antenna 2 change over relay. I had already taken the K3 out of line

Re: [Elecraft] KPA500 REFL HI Message - With Dummy Load

Carl, I have swapped cables, dummy load direct to Amp dummy load through tuner (in bypass) to amp, dummy load through SWR bridge to amp. Cables have been checked into a dummy load by SWR analyzer (realize this doesn't' take into effect power going through them. Have used accessory cable from

[Elecraft] K3 Data Modes using SignaLink USB

Got my cable in today to do soundcard data modes on the K3 with a SignaLink USB Not much chance of getting the cabling incorrect, installation was uber easy. I used the rear panel inputs and outputs for the additional isolation; allowing me to keep the Mic on the front panel for mixed mode

Re: [Elecraft] K3 Data Modes using SignaLink USB

to be set for Line Level output - it is plugged for mic level by default. See the manufacturer's documentation to see how to set it to line level output. 73, Don W3FPR On 10/12/2012 10:19 PM, David Little wrote: Got my cable in today to do soundcard data modes on the K3 with a SignaLink USB

Re: [Elecraft] K3 Data Modes using SignaLink USB

at the 5ht bar, and bars 1 through 4 do not indicate any ALC action at all. They are more like a VU meter provided to allow you some metering to help you adjust the audio level. 73, Don W3FPR On 10/12/2012 10:19 PM, David Little wrote: Got my cable in today to do soundcard data modes on the K3

Re: [Elecraft] Fw: KX3 - audio distortion after level 30

Yeah, if you are gonna take that route, a pair of Bose 901s, the EQ unit and a pair of Macintosh mono amps would be out Geez Louise, for $4.08 + $2.98 shipping you can buy a pair of foldable compact speakers from Amazon.com that will fill your room with audio. Powered from a USB port or wall

[Elecraft] K160RX K2 second antenna

Anyone looking to upgrade your K2 - I have for sale on eBay a K160RX kit. The bids starts at $12.00 plus flat rate shipping. Dave Little, AF5U __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

[Elecraft] 43 ft Vertical

The other half of this vertical antenna is the ground system. Without that other half, you will be wasting your time and money on the first half. The proof of this - you would never dream of putting up half of a dipole. Hi Hi 73, Dave Little, AF5U

[Elecraft] 43 ft Vertical Balun

Those of you who a thinking about a 43 ft vertical or how to feed it might read the links I have provided you here. I have built a 43 ft vertical from a 50 ft telescoping Rohn push-up pole. I am using a mesh ground system under it thanks to Home Depot's 4ft x 7 ft mesh sheets linked together,

[Elecraft] K2 VFO Stuck on 40M

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

[Elecraft] Buy ur K2

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

[Elecraft] Options for K2

Please email about any Elecraft options for K2. 100 w lid PA, ATU/100, I/O, NB, SSB, Audio Fltr or DSP ... Etc... Dave Little, AF5U 214.384.5171 iPhone __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft

[Elecraft] Purchase K2

I looking to buy a K2 with accessories. Please contact me. David Little, AF5U iPhone sent 214.384.5171 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post

Re: [Elecraft] [K3] Case screws rusting

On the Stainless Screws, a Black Magic Marker does wonders. Use a piece of Styrofoam to push the screws into, and give the heads a few coats. It is a renewable process that can be repeated every time they are removed. David KD4NUE Thanks to Bob MD0CCE for his efforts on Topband! He

Re: [Elecraft] Switching PS with the K3 - thoughts?

Another one that may be worth looking into (other than the suggestions presented already) is the Alinco DM-330MV Switching supply. It is metered, adjustable voltage, remotely accessible, small, quiet, well laid out, and it has a feature similar to Yaesu's Clock Shift, whereby you can shift any