Re: [Elecraft] K3S - blank screen - won't start won't shut off

Our club's K3 has had a similar  problem for several months.  It only occurs when you physically turn the K3 power off from the from the front panel.  The display stays lit, but remains blank.  Pressing the power button has no effect until I turn off the 13.8V supply, and turning it back on.  

Re: [Elecraft] K3 Config and Main Menu Dump?

: The easiest way to do this is simply to save the preferred/standard configuration using K3 utility.  And after other fingers have been at the radio, restore that saved configuration.  There’s no reason to have to look through individual menu settings. Grant NQ5T > On Nov 2, 2020, at 9:57 AM, Ed

[Elecraft] K3 Config and Main Menu Dump?

Is there a way to read back the K3 Config and Main Menu settings into a spreadsheet or CSV file?  I have two club K3 stations that occasionally experience some changes to the menus.  It would be nice to be able to quickly verify what the changes were, and if necessary restore the menus. Thanks

Re: [Elecraft] KAT500 EEPROM Problem

but you didn't say that you tried to reload the firmware. Have you tried to RELOAD the firmware? If you didn't reload the firmware, then I would suggest that you give that a try. 73, Ken K3IU ~ On 7/9/2020 12:37 PM, Ed via Elecraft wrote: > Our clu

[Elecraft] KAT500 EEPROM Problem

Our club K3 is connected to a KAT500, which is connected to 3 antennas (ANT1: Zero-Five vertical, ANT2: DXCC fan dipole, ANT3: 135ft doublet.  Yesterday I was using the K3 on 6 meters with ANT 1 and ANT2, which were not designed for 6 meters.  The KAT500 was able to tune for a low SWR, and the

[Elecraft] Weighted Knobs in K3?

Before I install 73inc weighted knobs on my K3S, is anybody of the opinion that these knobs cause long-term damage to the PTO shaft? These knobs are quite heavy, compared to the factory ones. Seems Elecraft used lightweight knobs for a reason. Input appreciated. 73, Ed NI6S

[Elecraft] For Sale: KSYN3 Board

Surplus to my needs, as I upgraded this to the latest. This came out of a working K3. Make offer. Thanks. 73, Ed NI6S __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

[Elecraft] Elecraft PR6-10 Preamp

This is the optional plug-in unit for the K3. Will add sensitivity, 22-54 MHz. Pls see link for more info: http://www.elecraft.com/manual/PR6- 10%20Owners%20Manual%20Rev%20A.p df Used only twice! $100 shipped 73, Ed NI6S __ Elecraft

[Elecraft] For Sale: KAT-3 Internal Antenna Tuner

Optional internal antenna tuner for the K3. $200 shipped. 73, Ed NI6S __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net

[Elecraft] FS: K3-100/F

All, I have upgraded to a new K3S and now have for sale a clean, bare bones K3, s/n 0959 (with optional KXV3A and stainless steel screws). This unit is in mint condition and has never been used in a contest. It probably has about 30 hours of use, max. My original intent was to upgrade this

[Elecraft] Interface Cable Recommendations?

Greetings. I would like to have auto band-switching and ALC between my K3 and Yaesu Quadra amplifier. Does anybody manufacture an interface cable that facilitates this? Thanks and 73, Ed NI6S __ Elecraft mailing list Home:

[Elecraft] Need Advice

I have had my K3 for a few years and have always kept it up to date. It seems cheaper than taking a loss in selling it and springing for a K3S. I am about to send it in again for the new synth boards and DSP board swap, etc. In the end, I will have 90% of a K3S. Is this the way to go?

[Elecraft] K3 remote power on.

We control our club's K3 with the free RemoteHams.com software.  An additional cable between the CAT connector routes the RTS through a transistor buffer to pin 8 on the AUX connector.  Here is a link that discusses the additional

Re: [Elecraft] Elecraft] KX3 - easiest way to panadapt?

What is " comocon " and why would I need it with NaP3 and my KX3 just to view the spectrum? Ed From: Chris Rutkowski [mailto:chrisr...@gmail.com] Sent: Saturday, October 17, 2015 4:53 PM To: k7...@yahoo.com; elecraft@mailman.qth.net Subject: Re: Elecraft] KX3 - easiest way to

Re: [Elecraft] Elecraft] KX3 - easiest way to panadapt?

va2fsq.com Sent from BlueMail <http://www.bluemail.me/r> On Oct 17, 2015, at 8:15 PM, Ed via Elecraft <elecraft@mailman.qth.net> wrote: What is " comocon " and why would I need it with NaP3 and my KX3 just to view the spectrum? Ed From: Chris Rutkowski [mailto:chri

Re: [Elecraft] Elecraft Hex Key Serial # 57

Don, didn't you mean, N3ZN? Ed K7AAT -Original Message- That worked well for me until I bought a paddle from K3ZN which has more than enough weight on the base to keep it solid. Don W3FPR __ Elecraft mailing list Home:

[Elecraft] KX3 - easiest way to panadapt?

I have a KX3. I would like to use my computer and laptop ( Windows 7 and Windows 8 ) to display a spectrum from my KX3, using the RX I/Q output. What is the simplest and recommended easiest way to do this? NaP3 ? I use my KX3 mostly on digital modes with SignaLink USB interface and

Re: [Elecraft] KX3 - easiest way to panadapt?

system over NaP3 and LP-Bridge. Second, you have more control of your KX3. 73, Barry K3NDM -- Original Message -- From: "Ed via Elecraft" <elecraft@mailman.qth.net> To: elecraft@mailman.qth.net Sent: 10/16/2015 6:24:37 PM Subject: [Elecraft] KX3 - easiest way to panadapt? >