Re: [Elecraft] What Two Bands would you pick for a K1?

I built my K1 when it was still possible to get the 4-band module which for me, covers 40, 30, 20 & 15. As I would like to have 80m also to work my Norwegian hams, I built a 2-band board with 80 & 20. 20m is a band that's normally always open some part of the day and a band you can use for dx,

Re: [Elecraft] KX3 QSK

Me too. In find that the "NEW QSK" is the same as the "OLD QSK" with a slight delay. It's better to turn down the RF gain if you get too much "popping" sound in your audio. 73 de Hal/LA4XX On 16-03-02 17:47, Ray W2RS via Elecraft wrote: > > The KX3 "NEW QSK" mode

Re: [Elecraft] [KX3][XPA100] KX3 drops out of PA MODE ON

Hi Glen. I've had this probleme several times and what I have to do (or at least do) is to disconnect the radio from the PC. After that it normally works. Maybe you have to switch the radio off/on. When everything works again, you can connect to the PC. 73 de Hal/la4xx On 16-01-21 08:51, Glen

Re: [Elecraft] When is mode A not mode A?

Hi. Well, I for one use mode B and have always done so. Probably because my first keyer only had mode B and secondly because I wanted to use the squeeze tchnique, as I thought that was the ultimate way to send morse code. I have no problems with mode B, but cannot use mode A without a lot of

Re: [Elecraft] WTB Elecraft K1 still

The KFL1-4 band filter module does not cover the 80m. only 40, 30, 20, 17/15. If you need the 80m you also need a 2 band module. 73 de Hal/la4xx On 15-10-17 05:02, KC6CNN wrote: > > I am still looking for a K1 4 band radio. > I would like to find one with 80, 40 , 30, 20

Re: [Elecraft] KX3-PX3-KXPA100 problem

Hi. I've also had this problem a couple of times. If you have the KX3 connected to a computer - disconnect. I think that solved the problem for me. You can connect to the computer again when the KXPA100 is up and running. 73 de Haø/la4xx On 15-03-12 22:59, David F. Reed w5sv.d...@gmail.com

Re: [Elecraft] List of K1 modifications

Hi Jim. Have a look at this page http://homepage.ntlworld.com/lapthorn/k1.htm. At the bottom you will find two links to sites decribing som mods made by others than Elecraft. Mods made by Elecraft (if there are any), you will probably find on the official Elecraft site. 73 de Hal la4xx

Re: [Elecraft] KX3] KXPA100 will not manual tune

Disconnect the amp and computer from the KX3. Switch the KX3 on and off. Reconnect the amp and switch on the KX3. This worked for me. You might check the menu key PA Mode to see if it's on. 73 de Hal/la4xx On 14-12-26 22:38, George via Elecraft elecraft@mailman.qth.net wrote: Was working

Re: [Elecraft] KX3 firmware to-to list

So did I. It's over two years since Wayne promised to look at this after he returned from his summer vacation. He agreed that the weight was not good enough.  73 de Hal/la4xx On 14-09-24 21:57, Joe W2KJ w...@bellsouth.net wrote: I thought that increasing the weight settings on the internal

Re: [Elecraft] K1-4 4 band version gone?

I use the technique with the rubber band and change filter board in 5 minutes from I start to unscrew the first screw of the top cover.  73 de Hal/la4xx K1 2929 On 14-07-23 19:12, Mike Morrow k...@earthlink.net wrote: Changing band modules is a special pain for me because installed the

Re: [Elecraft] KX-3 NR1 adjustment?

By turning the (AF/RF - SQL) knob rigth above the NR button.73 de Hal/la4xx On 14-04-21, lane zeitler via Elecraft elecraft@mailman.qth.net wrote: How do you adjust the amount of NR on NR1 on the KX3? My menu reads 10. Thanks. Lane Ku7i JH1JCM

Re: [Elecraft] KX3 firmware question

MCU 1.87 / DSP 1.28 11-26-2013 73 de Hal la4xx On 14-02-19, Gerry leary gerrylear...@icloud.com wrote: What is the version number of the current KX3 firmware that is available? Sent from my iPhone this time __ Elecraft

Re: [Elecraft] KX3 audio quirk

I have noticed something similar, but that has nothing to do with the KXPA100. Whe I switch on NR, the audio is muted. Pushing the PBT button to get NORM bandwith gets the audio back, but if I try to change the bandwith it is muted again. Strange. Without NR on there is no such strange

Re: [Elecraft] KX3 Headphone Clicks

Yes, this is a known issue. Try to turn down the AF gain when keying. That will make it much better.73 de Hal la43xx On 13-12-30, Klaus Koppendorfer k...@ccf.net wrote: that is what we had several times told to elecraft, qsk on kx3 is bad, you can read this also at bob sherwood

Re: [Elecraft] KX3 Headphone Clicks

, 12:53 AM, Hjalmar Duklæt wrote: Yes, this is a known issue. Try to turn down the AF gain when keying. That will make it much better. 73 de Hal la43xx On 13-12-30, Klaus Koppendorfer k...@ccf.net wrote: that is what we had several times told to elecraft, qsk on kx3 is bad

Re: [Elecraft] K-1 power out vs current draw.

According to the manual the K1 will deliver around 5W at 14V (varies between bands), and the current draw is around 55mW (without display backlight). It can be operated on a voltage between 8.5 - 15V. Hal/la4xx On 13-12-19, k...@juno.com k...@juno.com wrote: Good folk, In the planning

Re: [Elecraft] Customized Radio Stands

For me it looks like the paddles are positioned too high above the desk on this stand? 73 de Hal On 13-11-07, Richard Newstead rich...@sotabeams.co.uk wrote: Dear all As I don't own a KX3 I was not able to take any photos of the new stand with one in place. However, the first ones are now

Re: [Elecraft] K1-4 Low power output only on 15 meters.

Hi Jim. I've had the same problem with my K1. It turned out to be a bad crystal, so my suggestion is to get another crystal for the 15m band. 73 de Hal la4xx On 13-06-12, Jimithy66 jimith...@gmail.com wrote: My K1 was a wonderful radio on all bands 40 - 17m. However 17m saw very little use

Re: [Elecraft] My in-progress K1 is ALIVE!!!

Hi Paul. Congratulations!! This reminds me of when I put mine together some two years ago. I also trimmed the caps by ear. Plugged in my dipole and found a German station on 20m. Called him and he replied with a report of 579. Just after that I worked Senegal, Africa. I was totally hooked and

Re: [Elecraft] Suggested key/paddle for CW for a the K3 and others (not expensive)

Hi Cliff. Have a look at this site http://cwtouchkeyer.com/. I've been using these paddles for nearly two years and my opinion is that they can not be beaten by any mechanical paddles, and I've tried quite a few during over 30 years of cw operation.And they are very cheap too. 73 de Hal/LA4XX

Re: [Elecraft] Newbie ....

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

Re: [Elecraft] kX3 and L ion battery

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

Re: [Elecraft] [K1] RF Board Resistance Checks

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

Re: [Elecraft] K1 Kit Question

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

Re: [Elecraft] KX3 oddity when changing bands

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

Re: [Elecraft] CW Key suggestions ?

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

Re: [Elecraft] K1 calibration question.

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

Re: [Elecraft] K1 no power out B2

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

[Elecraft] PLease stop OT threads

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

Re: [Elecraft] KAT500 now on order form

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

Re: [Elecraft] KX3 Order made Dec 31st at 1346

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

Re: [Elecraft] backlight in unbuilt k1

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

Re: [Elecraft] VFO tuning range of 150Khz

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

[Elecraft] Mails bouncing back

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: