and it will work the first time you fire it up.
73,
Fred, KC9QQ
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K2-7375-Progress-tp7564785p7566418.html
Sent from the Elecraft mailing list archive at Nabble.com
bandwidth of the crystal and DSP filters. For
convenience I use the same bandwidth in both filters at a given
selection setting--XF1=AF1, XF2=AF2, etc.
Good luck and 73
Bob N6WG
The Little Station with Attitude
/
Thanks,
Fred, KC9QQ
--
View this message in context:
http://elecraft.365791.n2
,
Fred, KC9QQ
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KDSP2-Board-Layout-Image-tp7560434.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net
have two questions:
1. Should I be concerned that these resistors are not on the Rev E board?
2. What is the purpose of the additional resistors?
Thanks,
Fred, KC9QQ
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KSB2-Problem-with-Assembly-tp7560131.html
Sent from
!! I would like to be able to tie the symptoms to the location of the
bad connection.
Thanks,
Fred, KC9QQ
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Question-about-jumper-wire-on-control-board-tp7560052.html
Sent from the Elecraft mailing list archive at Nabble.com
Thanks Don. I downloaded your procedure and will go through it this week.
Thanks again for your quick response.
Fred
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K2-Dial-Calibration-Question-tp7559958p7559990.html
Sent from the Elecraft mailing list archive at
installed the K2IO and started to use Spot
Collector spots to tune the rig through the K2IO. When I tune in spots I
noticed that they are off by about 200 cycles. I only use the rig for CW
QRP so I had not noticed this before. I do not have a K2 SSB adapter in the
rig.
Fred, KC9QQ
--
View
Don,
Thanks for you detailed reply. I think I will install the KIO2 first so I
can interface the K2 to my computer for CW contesting.
I don't know if I was being very patient or just afraid I would break the K2
which was already working so well!
Fred, KC9QQ
--
View this message in context
for one of our Indiana snow storms this winter.
Thanks,
Fred, KC9QQ
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Accessory-Build-order-tp6987212p6987212.html
Sent from the Elecraft mailing list archive at Nabble.com
,
Fred, KC9QQ
--
View this message in context:
http://n2.nabble.com/K2-working-on-40M-tp4554916p4557987.html
Sent from the [K2] mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo
,
Fred, KC9QQ
--
View this message in context:
http://n2.nabble.com/K2-kit-recieved-tp4467882p4470831.html
Sent from the [K2] mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo
Here is a link to N0SS's website which has a number of K2 mods.
http://www.n0ss.net/index_k2.html http://www.n0ss.net/index_k2.html
Yves Dussault wrote:
I see on page 84 of my manual a reference to the associated application
note, about installing a SPLIT/RIT/XIT led.
Where can I find
day projects. I hope
you have as much fun with the K2 as I am having.
Fred, KC9QQ
WE0H wrote:
Just got done testing the TX RX on K2 S/N 6698 and all is working per
the manual. Now onto the options...
Mike
WE0H
__
Elecraft
.
Here is the link to the site: http://www.qth.com/topten/abss.htm
http://www.qth.com/topten/abss.htm
Fred, KC9QQ
Greg Buhyoff wrote:
Group,
This is off topic and I would deeply appreciate any responses to be
sent to me off list. I am posting here because I respect the
knowledge
a
magnifier takes a little getting used to, but once you develop the hand eye
coordination of the iron under the magnifier you will find it much less
stressful making the solder connections.
I bought a low cost lighted magnifier from Staples for around $30. It was
worth every penny.
Fred, KC9QQ
KC9QQ wrote:
I also just noticed that the power output transistors Q7 and Q8 are
getting
warm when the power is on. I did not say before but, their is no display
or any other activity on the control board or front panel.
Fred, KC9QQ
KC9QQ wrote:
KC9QQ wrote:
I also just noticed that the power output transistors Q7 and Q8 are
getting
warm when the power is on. I did not say before but, their is no
display
or any other activity on the control board or front panel.
Fred, KC9QQ
I also just notice
transistors Q7 and Q8 are
getting warm when the power is on. I did not say before but, their
is no display or any other activity on the control board or front panel.
Fred, KC9QQ
__
Elecraft mailing list
Home: http://mailman.qth.net
KC9QQ wrote:
Don Wilhelm-4 wrote:
Fred,
In cases like yours, first step is to connect a dummy load to the K2
just in case it is trying to transmit - it is not good to enter transmit
state without a load on the PA transistors. If it is a K2/100, remove
the KPA100 and connect
display to
start receiving CW.
Fred, KC9QQ
--
View this message in context:
http://n2.nabble.com/HRD-cw-copy-tp2192917p2193412.html
Sent from the Elecraft mailing list archive at Nabble.com.
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
20 matches
Mail list logo