[Elecraft] KX3 - sounds like filter blow-by - what am I hearing?

I have been using a KX3 during FD, connected to some large (tower/yagi) antennas. Am operating CW exclusively. Although I've had the KX3 for a while, I've only used it casually until today's FD. All day I've been noticing (on 20 and 40M, with fairly strong signals - some ove S9 - across both

Re: [Elecraft] KX3 - sounds like filter blow-by - what am I hearing?

.) The FC setting doesn't seem to interact with this. Thanks again any further advice! Dave -- On Sat, Jun 27, 2015 8:01 PM MDT David Feldman wrote: I have been using a KX3 during FD, connected to some large (tower/yagi) antennas. Am operating CW exclusively. Although

[Elecraft] KX3-2M can be ordered

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

[Elecraft] Progress update on KX3-2M module?

Checking at end of April 2014 Any update appreciated - roving plans for June VHF contest... __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

[Elecraft] KXPA100 use with K3-10?

This may already have been asked and/or answered (so please forgive the redundant request), but my question is this - is the KXPA100 is expected to be usable (externally) with a K3-10? I have a K3-10 and would rather use a future KXPA100 with it for the occasions where higher power is needed

Re: [Elecraft] KXPA100 use with K3-10?

Wow - much clearer/faster answers than I expected! I would not need an internal tuner to the K3, so I'm good-to-go and anxiously awaiting order opportunity for KX3 and KXPA100! Dave On Thu Jun 16th, 2011 5:13 PM MDT Wayne Burdick wrote: Yes. Wayne On Jun 16, 2011, at 4:02 PM, David Feldman

Re: [Elecraft] New K144XV/KXV3A - problems on 2M - 1 milliwatt calibration ERR TXG and 'Unexpected response DB 0.56 MW; to DB; State 153'

. 73 Dave WB0GAZ wb0...@hotmail.com Message: 13 Date: Tue, 23 Mar 2010 17:12:29 -0600 From: david feldman wb0...@hotmail.com Subject: Re: [Elecraft] New K144XV/KXV3A - problems on 2M - 1 milliwatt calibration ERR TXG and 'Unexpected response DB 0.56 MW; to DB; State 153

[Elecraft] New K144XV/KXV3A - problems on 2M - 1 milliwatt calibration ERR TXG and 'Unexpected response DB 0.56 MW; to DB; State 153'

Seeking advice while trying to get KXV3A/K144XV added to existing K3-10. May be operator error. Detail below. Rig's history: K3 SN 18xx, no options (single 2.7 kHz 5-pole filter), built from kit when first received (Fall 2008), used successfully for a little while, then stored until today

Re: [Elecraft] New K144XV/KXV3A - problems on 2M - 1 milliwatt calibration ERR TXG and 'Unexpected response DB 0.56 MW; to DB; State 153'

Partially fixed - I had set XV1 ADR to TRN1 instead of INT TRN1. Once I changed that, I found many problems corrected - I was able to set the two offset frequencies, I hear the relay switching between band segments, and I am now able to receive on 2M. However, I repeated the calibration using

[Elecraft] K144XV followed by KPA3?

If a K144XV is purchased for a basic (10W) K3, then later a KPA3 is added, does the K144XV module need to be replaced or can it be re-used? An entry (copied below) from www.elecraft.com/elecraft_prod_list.htm#k3 says there are two ways to order K144XV, but an e-mail to elecraft asking how I'd

RE: [Elecraft] soldering station info, from a guy who

As you'd expect, for professional use, the Pace and the Metcal are the most costly - and the best at what they do. I'm curious what makes one unit better than another other than the obvious differences between a temperature-controlled iron and a $10 radio shack unit. Are you thinking of

[Elecraft] WTB KX-1 assembled/running

Functional, but cosmetics not important. E-mail off-list 73 Dave WB0GAZ [EMAIL PROTECTED] ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.):

RE: [Elecraft] Feasibility of KPA-1(?)

Hello Jim, The two solutions I've looked at so far are unappealing (going all the way to the 100W level, or the hfpack-based project which includes a DC/DC converter to run it's transistors at 28V, which has it's own efficiency impact.) I have been looking for a more modest power increase,

RE: [Elecraft] Feasibility of KPA-1(?)

PROTECTED] To: 'david feldman' [EMAIL PROTECTED],elecraft@mailman.qth.net Subject: RE: [Elecraft] Feasibility of KPA-1(?) Date: Sun, 3 Apr 2005 18:12:34 +0200 Sorry, excuse I hit the wrong button. No my response to the mail Swiss Hams always need 80m due to their yearly traditional National Mountain

[Elecraft] K1 - 6 bands simultaneously?

This is probably FAQ, but I'm curious if/how the K1 is set up for 6 bands simultaneously (basically a K1-4 with an extra 2-band filter module.) I'd really like to find a way not to have to open the rig to switch between band sets, and would like to have access to 80 and 15/17 along with the

[Elecraft] OXY-BATT?

Oxyride cells were shown at CES/Las Vegas 1/06/05. Eagerly anticipating for KX-1 73 Dave WB0GAZ [EMAIL PROTECTED] ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change,

[Elecraft] Max DC supply voltage for KX-1

Is the KX-1 capable of operating from twelve NiMh cells (~16-17V at full charge?) without being damaged? Interested in using it self contained (six AA NiMh cells) or with additional supply voltage (more cells) added externally and wired in series with the internal cells, and wonder what the