Subject: [Elecraft] K3 Utility help in England, please
Dear UK K3 owners,
This email is a request for some help in troubleshooting my recently
acquired K3. It is an early model Ser No 104 and has been hardly used. I
suspect I am suffering from front panel to RF board pin corrosion problems
since
Dear UK K3 owners,
This email is a request for some help in troubleshooting my recently acquired
K3. It is an early model Ser No 104 and has been hardly used. I suspect I am
suffering from front panel to RF board pin corrosion problems since K3 utility
fails to connect and comes up with the
I installed the utility and installed what I think is the driver via CDM
c2.08.30 WHQL Certified.exe
I connected the KUSB cable to the K3’s RS232 port. I started the utility and
selected COM3 as it was the only choice.
The utility cannot find the K3.
What am I missing?
Carl Yaffey K8NU
Banjo,
check the utility baud rate is set correctly to match the k3's baud rate
CONFIG RS232
On 2/4/2014 3:06 PM, Carl Yaffey wrote:
I installed the utility and installed what I think is the driver via CDM
c2.08.30 WHQL Certified.exe
I connected the KUSB cable to the K3’s RS232 port. I started the
Assuming Windows, what does device manager say about the port? No other
program is using the port, right? Have you tried a reboot of the puter? Is the
DB9 firmly attached to the K3? When you plugged the USB cable into the 'puter
did Windows recognize it?
That's all I got
73 Mike NF4L
I think the k3 Utility will match whatever the K3 is set to. AFAIR, it cycles
thru all the baud rates.
73, Mike NF4L
On Feb 4, 2014, at 4:19 PM, Sam Morgan k5oai@gmail.com wrote:
check the utility baud rate is set correctly to match the k3's baud rate
CONFIG RS232
On 2/4/2014 3:06 PM,
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Mike Reublin
Sent: Tuesday, February 04, 2014 1:26 PM
To: Elecraft Reflector
Subject: Re: [Elecraft] K3 utility help
I think the k3 Utility will match whatever the K3 is set to. AFAIR, it
cycles thru all the baud rates.
73, Mike NF4L
On Feb 4, 2014
Mike,
That may be true, but if the P3 is in place, the K3 rate must be set to
38,400 or some things will not work together. I don't know whether a P3
is involved in the original post or not.
73,
Don W3FPR
On 2/4/2014 4:25 PM, Mike Reublin wrote:
I think the k3 Utility will match whatever
True, Don and good point. But the utility still does the seek. It's not
possible to match the utility and K3 manually.
Mike NF4L
On Feb 4, 2014, at 4:45 PM, Don Wilhelm w3...@embarqmail.com wrote:
Mike,
That may be true, but if the P3 is in place, the K3 rate must be set to
38,400 or
you are quite correct,
just goes to show I am playing with to many different pieces of software
that aren't as smart as elecraft's utils g
On 2/4/2014 3:25 PM, Mike Reublin wrote:
I think the k3 Utility will match whatever the K3 is set to. AFAIR, it cycles
thru all the baud rates.
73,
I'd like to thank everyone that responded to my plea for help after a
lightning strike knocked
out K3 utility. After advice from the mailing list-and from k3 support-akio3
main board-daughter board
and new serial-usb cable solved the problem. Thanks for everyone's help.
11 matches
Mail list logo
