In a recent message, Sverre Holm (LA3ZA) la...@nrrl.no writes
I wonder what's the experience with the MV89A, does it need a lot of
adjustment of the control voltage, or does it have this kind of accuracy out
of the box?
No, Sverre, I did not need an adjustable 5V control voltage as the MV89A
was
The uC 04.86 FW REVS is the firmware revision number. From this screen
the VFO B knob should cycle through the config parameters and the VFO A
knob will cycle through the values available for the selected parameter.
From the FW REVS screen, if rotate the VFO A knob clockwise a little,
it
On 9/20/2014 4:24 AM, Michael Eberle wrote:
From the FW REVS screen, if rotate the VFO A knob clockwise a little,
it should change to something like d1 02.83 which is the DSP firmware
revision. I am curious if it will do this, but not change the frequency
when you exit the menu.
No, turning
I've had a few responses to my earlier query re using the Heil Proset
iC with the K3, others who have had similar problems - you are not alone!
Here is my original post:
Using the K3, has anyone else had problems with the Heil Proset
supplied by Elecraft (model iC) as to audio feedback on
Thanks for the help and the good ideas. I will find a stereo plug first, and
go from there. YES, the K2 is a great little rig! 73
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K2-Straight-key-auto-detect-tp7593193p7593232.html
Sent from the Elecraft mailing list
Test
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email
The best way to determine if a problem is or is not produced by RF
Feedback is to operate with the transmitter working into a dummy load.
If the problem goes away, there is a 99% chance it is RFI.
This comment is not confined to the K3 or any other Elecraft gear, it
can be any transmitter.
Go to the INP menu, edit the parameter and tap
DISPLAY to toggle ADET on or off. With ADET set to ON, you should be
able to key the K2 from the straight key (or computer) even though the
INP menu is set to PDLn or PDLr.
Thanks, Gene, for posting the original question and, Don, for the
On 9/20/2014 8:36 AM, Ron Wetjen wrote:
Will try to take a look at the encoders later today and double check to
see that they are installed correctly.
Disassembled the front panel ... and reinstalled the encoders. That
corrected the problem. Both VFO's are working now.
On to the setup!
Whichever one you decide on, I'd strongly suggest you get something,
otherwise the battery will need a a LOT of attention. I have the AA
smart charger and it works like a charm with zero attention to it.
Tom
wb2qdg
k2 1103
On 9/18/2014 10:59 PM, Doug Hensley wrote:
Elecraft referred me to
Hi folks,
received my 2M module this week. Assembly went fine, everything as
described in the instructions.
TX works great, I can drive my PA with 1.5W.
RX is also quite sensitive. Worked 2 stations via TR 400km, both were
running less power than I did.
But: The tuning noise problem which I
Would it be possible to get the k3/kx3 freq memory editor ver 1.3.3.0
updated to allow entry of the NOAA weather channels?
162.400, .425, .450, .475, 162.500, .525, .550
currently i get a little red exclamation mark error.
Jeff Herr, WW6L
4636 Kelton Way
Sacramento, Ca 95838
916.925.6089
Thanks David,
David G4DMP wrote
No, Sverre, I did not need an adjustable 5V control voltage as the MV89A
was spot on 10,000,000.00 Hz
-
Sverre, LA3ZA
K2 #2198, K3 #3391,
LA3ZA Blog: http://la3za.blogspot.com,
LA3ZA Unofficial Guide to K2 modifications:
The K3/KX3 can't tune those frequencies ... even with the
2 meter transverters. Those frequencies would be well above
30 MHz (IF limit).
73,
... Joe, W4TV
On 2014-09-20 5:31 PM, Jeff Herr wrote:
Would it be possible to get the k3/kx3 freq memory editor ver 1.3.3.0
updated to allow entry
Gernot,
did you activate the RXSHFT on 2 m? That should take care of it. Think
there's a remark on that in the KX3-2M manual, too.
73, Olli - DH8BQA
Contest, DX radio projects: http://www.dh8bqa.de
Am 20.09.2014 23:23, schrieb g...@gmx.net:
Hi folks,
received my 2M module this week.
My understanding is that the KX3 (not the K3) _CAN_ tune the WX band for RX.
Bruce/N1RX
The K3/KX3 can't tune those frequencies ... even with the
2 meter transverters. Those frequencies would be well above
30 MHz (IF limit).
73,
... Joe, W4TV
On 2014-09-20 5:31 PM, Jeff Herr
Hey, Joe --
From the Elecraft KX3 Module FAQ:
*Q:What frequency range will the module cover?*
A:On 2 meters: About 120 to 165 MHz, allowing copy
of weather-band stations at 162 MHz, airport tower
AM in the 120 MHz range, etc. On 4 meters: About
65-72 MHz. Sensitivity gradually falls off
The KX3 with KX3-2M is able to tune frequencies in the range 120-168
MHz. See p53 of the owner's manual for the specs.
73,
matt
W6NIA
On Sat, 20 Sep 2014 20:45:45 -0400, you wrote:
My understanding is that the KX3 (not the K3) _CAN_ tune the WX band for RX.
Bruce/N1RX
The K3/KX3 can't tune
OK guys ... I get the message. The K3 is not able to tune Weather band.
73,
... Joe, W4TV
On 2014-09-20 9:10 PM, Matt Zilmer wrote:
The KX3 with KX3-2M is able to tune frequencies in the range 120-168
MHz. See p53 of the owner's manual for the specs.
73,
matt
W6NIA
On Sat, 20 Sep 2014
The weekly Elecraft SSB net meets Sunday at 1800Z on 14.3035 MHz. Join us.
73,
Phil, NS7P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
20 matches
Mail list logo