[Elecraft] WTB P3SVGA Board

I understand Elecraft no longer sells the P3SVGA Board for the K3/K3s. I'm looking for the board and associated cabling for a K3 if anyone has one they would be willing to part with. Thanks,Mike KD8RQE __ Elecraft mailing list Home:

[Elecraft] Kpod data cable

I seem to have misplaced the data cable that connects the Kpod to my K3. Is this any kind of standard cable or do I need to get a new one from Elecraft? Thanks. Mike KD8RQE __ Elecraft mailing list Home:

Re: [Elecraft] Kpod data cable

any standard cable you can watch your VFO drift off frequency while you're in a QSO. Directions are provided for making your own. http://www.elecraft.com/manual/E740285%20KPOD%20Owner%27s%20Manual%20Rev%20D.pdf 73, Dennis NJ6G On 2/4/2018 03:38, Mike via Elecraft wrote: > I seem to have mis

Re: [Elecraft] kxpd3 question

Hi Jerry, I made the decision to use a single lever paddle and not learn the "squeeze" technique needed to run a dual lever paddle. Several reasons: The truly high speed guys use single lever paddles--they feel they make fewer mistakes with the single lever. If you learn the single lever

Re: [Elecraft] KLPA3A power transistor thermal stress concerns

The K3/100 switches to the KPA3A at 12 watts. So is there a 2w range (10-12w) where the KLPA3A is putting out unacceptable IMD? Is there a way to make the switch at 10w, or should we just avoid that 2w "danger zone"? 73 Mike KD8RQE In a message dated 10/24/2017 10:56:38 A.M. Eastern

[Elecraft] KX3: Roofing filter behavior

Hi, It is written in the manual (p. 39) that: "Roofing Filter Configuration for SSB Mode: Roofing filter FL2 (3 kHz) can be inserted when the upper edge of the receive passband reaches either 2.4 kHz (default value) or 2.9 kHz. When the passband edge is higher than this, FL1 is used (wide

[Elecraft] KX3 roofing flters vs IC-7300

Hi guys, I have a KX3 with roofing filters installed. I also have an IC-7300. Will KX3 have an advantage on receive in noisy environment and what is the best way to use them (SSB and CW)? Thanks!MikeAB3VN __ Elecraft mailing list Home:

Re: [Elecraft] CP1 vs other directional coupler

These guys have several. Well built. Not cheap. http://www.preciserf.com Mike KD8RQE In a message dated 5/28/2017 1:25:49 P.M. Eastern Daylight Time, mike.ab...@gmail.com writes: I'd like to get a directional coupler to, among other things, monitor my transmit signal on a scope. The

Re: [Elecraft] Elecraft Equipment chat group

No thanks. Mike KD8RQE In a message dated 5/1/2017 9:51:49 A.M. Eastern Daylight Time, va...@portcredit.net writes: Someone did change this to OT, but it really isn't. As others have also mentioned is that this is a list that is heavily diluted by so many OT issues. This is the only

Re: [Elecraft] Linear thoughts

1. Separate power supply or small control box (ala ACOM 2000A). Same form factor as K line if separate power supply (small control box able to control an integral or separate "KAT1500" as well). 2. Solid state. 3. Full integration with K line similar to KPA500 and easy integration with

Re: [Elecraft] KX3 2m external amplifier

Ed, KL7UW, built me a nice 80w 2m amp for less than $400. http://www.kl7uw.com Mike In a message dated 7/28/2016 12:54:12 P.M. Eastern Daylight Time, dhand...@plantron.se writes: Does anyone use a KX3 + internal 2m transverter with an external amplifier? I am looking for any

[Elecraft] K2

Thanks for all he replies and advice. I'm looking forward to enjoying this project. It's been quite a while since I've built anything and I remember it fondly. 73 Mike KD8RQE __ Elecraft mailing list Home:

[Elecraft] K2

A K2 kit is on it's way. Although I do have some experience soldering, it has been 30+ years and I am open to any suggestions as to equipment needed. I have a Hakko FS-951 soldering station. I have seen various mechanisms for holding the circuit boards while working on them. Any other

Re: [Elecraft] Announcing the KX2 80-10 m, SSB/CW/Data transceiver

Will the Begali "Adventure" paddles fit the KX2 as well as the KX3? Mike KD8RQE In a message dated 5/19/2016 5:37:10 P.M. Eastern Daylight Time, n...@elecraft.com writes: Introducing the Elecraft KX2 transceiver -- the newest member of our compact KX Line. The KX2 has features very

[Elecraft] Hamvention discounts

Any advantage to ordering during the Hamvention? If so, do the same discounts apply to phone or internet orders or do you have to be physically present in Dayton to take advantage? Thanks. 73 Mike KD8RQE __ Elecraft mailing list

[Elecraft] Speaker for K3

I've been happy with 2 Palstar SP30B's. Mike KD8RQE __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by:

[Elecraft] OT Generac Generators

15 KW Generac with 550 gal propane tank. Live out in the country and have gone 14 days without power. I'm good for 2-4 weeks, depending on load. Mike KD8RQE __ Elecraft mailing list Home:

[Elecraft] K3 AF Gain

I know I'm probably stupid and missing something obvious, but when I turn on the sub receiver it is much louder in my right ear than the main is in my left with the AF gain set the same on both receivers and both VFO's tuned to the same frequency. RF gain is set the same on both receivers.

Re: [Elecraft] K3 AF Gain

and balance. If you are in balance mode and you want them to be the same you have to set the Sub AF Gain knob to the middle. Buck k4ia K3# 101 KX3 #715 On 7/19/2014 5:11 PM, Mike via Elecraft wrote: I know I'm probably stupid and missing something obvious, but when I turn on the sub receiver

[Elecraft] Learning CW

I have wanted to learn CW and be a ham since I was 8. I started and stopped 5 or 10 times in the next 52 years. I was finally licensed in Feb 2012 as a General and upgraded to Extra 6 months later, but I was old school enough to not consider myself a true ham until I could do CW, so I