Well, perseverance pays, sometimes.I realize this mic probably came from China,
but...
the connections to the end of the cable, in the mic housing, weren't well
handled.
The connection of the black wire to the shield was made so near the end of the
outer jacket that overheating other wires was
My want has been fulfilled. Thanks for the inquiries
73 de K6SBA
David
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This
If anyone has an MH2 hand mic in excellent operational and cosmetic condition,
I would like to purchase it.
Tnx es 73 de K6SBA
David in Santa Barbara, CA
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
And a Mea Culpa from me.
I have a MH2 that I use very infrequently with my K2 and it works well.
When the question was asked, I noted the instructions were different for
the K3 but failed to read them carefully. I should have tried my MH2 on my
K3 before offering advice.
I have only a casual
Gentlemen, thank you very much. One of the nice things about Elecraft is all
the good feedback you get from users!
Mike NJ2OM
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home:
I am sorry to disagree, but the MH2 will work fine for both the K2 and
K3. They are interchangable. After the repair and configuration of
over 1000 K2s, I am quite familiar with the K2 microphone configuration
for various microphones.
Yes, the K2 mic config header must be jumpered properly
Download the MH2 instructions from Elecraft site and you will see that the
mic has different jumper settings for the K3. I’m not sure if an MH2
configured for K2 will work unchanged with K3. The K2 config in the mic
has a resistor that is not there for K3. At least that is the way I read
it.
Hello Mike
Yes, it works with K3
https://ftp.elecraft.com/MH2/E740030_MH2_Rev_D.pdf
73,
Enviado desde mi iPhone
> El 26 ene. 2021, a la(s) 15:14, NJMike escribió:
>
> Will the MH2 hand mic that was originally for the K2 work with the K3? I
> know there is an MH4 mic now that works with
Mike,
Yes, no problem. It needs bias. The MH4 was the replacement when the
MH2 was no longer able to be sourced by Elecraft.
73,
Don W3FPR
On 1/26/2021 1:13 PM, NJMike wrote:
Will the MH2 hand mic that was originally for the K2 work with the K3? I
know there is an MH4 mic now that works
Will the MH2 hand mic that was originally for the K2 work with the K3? I
know there is an MH4 mic now that works with both rigs.
Thanks,
Mike NJ2OM
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home:
Does the MH2 mic for the K2 work with the KX3?
tnx
ed
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
The MH2 has an 8-pin connector and I believe the KX3 mic uses a 1/8
tip-sleeve-ring plug. You might be able to make an adapter for it though.
Mike
KI0HA
On 9/14/2014 2:06 AM, Eddy via Elecraft wrote:
Does the MH2 mic for the K2 work with the KX3?
tnx
ed
Ed,
No, the connector will not fit the KX3.
If the question is 'will the MH2 work using a homebrew adapter', then
the answer is yes.
73,
Don W3FPR
On 9/14/2014 3:06 AM, Eddy via Elecraft wrote:
Does the MH2 mic for the K2 work with the KX3?
tnx
ed
Kenwood mic does not use bias (it is dynamic). Elecraft requires
bias. Measure between pins 1 and 7 to confirm bias (2.2 to 3.3V -
industry standard for AV mics).
Also check to make sure the microphone is wired correctly - mic
ground must be on pin 7, PTT ground must be on pin 8. If the two
Dear guys,
Please, any friend use the hand mic (MH-2) with a MicrokeyerII interface?
Best Regards
Ric
PY2PT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
The MH2 is an electret mic wired with a Foster plug having Elecraft's
Kenwood compatible pin assignments. The microHAM DB37-EL-K3R and
DB37-EL-K23 cable sets are configured for the Electaft/Kenwood standard
and the supplied Foster to RJ-45 adapter cable allows connecting the
MH2 to the rear
Dear Joe,
I've tried both jumpers position and nothing!!!
With my kenwood hand mic everything is ok. But with the MH-2 mic (even changing
the jumper position) nothing!!
Best Regards
Em 23/02/2013, às 23:31, Joe Subich, W4TV escreveu:
The MH2 is an electret mic wired with a Foster plug
Does anybody have a spare MH2 Mic that they would like to get rid of. Please
Email me at
k8...@yahoo.com. tnx 73 Jim K8DYZ
Best Wishes Carol Jim Navarre K8DYZ
__
Elecraft mailing list
Home:
Hi ALL
I got my MH2 mic or the k2 and there was no resistor in the box ACK!
I know its a 5.6K Green Blue red, and its a 1/4 watt but is there a better
choice?
and should I get a gold or a silver tolerance?
Off to the telephone shack tomorrow
-Neil
Neil,
The resistance is not critical, so if you have a resistor (of any
tolerance) between 4.7k and 6.8k on hand use that.
Did you have a tan envelope on the package with the 8 jumpers for the
microphone configuration header? If so, look very carefully in that
envelope, the resistor can get
Don, Thank you for the help, and I did just that, tore the envelope up and
it still wasn't there. Radio is waiting, its ok, its been weeks, it will
wait 1 more day.
-Neil
On Thu, Jul 22, 2010 at 8:29 PM, Don Wilhelm w3...@embarqmail.com wrote:
Neil,
The resistance is not critical, so if you
Hi All:
I'm new to this list. As of last week, my K2 s/n 6770 is up and
running - I'm quite happy with it. Even though I have a stealth sloper
to a pine tree (HOA restriction), the receiver has impressed me, and
the QRP gets out (next weekend's board is the 100W PA). This weekend I
got
Steve,
Re-check those instructions for the MH2. The resistor goes between pins
1 and 6. Pin 1 is the AF line, and pin 6 is the 5 volt line. You must
pipe voltage to the AF line on the mike (through the resistor) to make
it produce audio.
BTW, pin 2 is the PTT pin.
73,
Don W3FPR
Stephen
Thanks to all. The mic is sold.
SidShusterman wrote:
Brand new! Never used. $40 includes shipping CONUS. Paypal no fee.
Reply directly to me please.
73,
Sid
Brand new! Never used. $40 includes shipping CONUS. Paypal no fee.
Reply directly to me please.
73,
Sid
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Hi Norm. It took me a while to find this as well. Page 51, Owner's
Manual: Main Menu: MIC SEL: tap the number 2 on the keypad to toggle Bias.
Ann VA3NOE
Norm Greenaway wrote:
Recently received my K3/100 s/n 1650.
But need help activating MH2 mic.
Have followed all the manual procedures but
Recently received my K3/100 s/n 1650.
But need help activating MH2 mic.
Have followed all the manual procedures but still
unable to turn bias on in mike.
any suggestions
73 VK4FNWG
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be
: Thursday, March 27, 2008 2:38 AM
Subject: Re: [Elecraft] MH2 Mic
Ken,
It is not from lack of use, it is very, very stiff.
Best,
DW Holtman
WB7SSN
- Original Message -
From: Ken Kopp [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
Sent: Wednesday, March 26, 2008 8:13 PM
Subject
Yes, a bit stiff - a bit of stretching and flexing (forgive the pun)
have helped.
Much stiffer than my Yaesu Ft-857 mic
--
The secret of life is honesty and fair dealing. If you can fake that,
you've got it made. -Groucho Marx
On 27 Mar 2008, at 07:11, David Cutter wrote:
The manufacturer has
Very disappointed in the mic cord. Poor QC in my opinion
I was going to send it back to Elecraft, but decided to replace the cord
with a very flexible thin rubber coiled cord removed from a spare $5
cheap dynamic CB microphone Workman electronics Super Star DM-507-4.
The Superstar is not a bad
I see several guys using the Kenwood MC 43 S mic with K3..
any comparisons. with the MH2. ?
Which is better...looks like they cost about the same
Mike Miller KA5SMA
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a
The MH-2 that I received with my K3 has ... in my
opinion ... a really stiff coiled cord. It's capable
of sliding the radio on the desk when the mic is held
about 24 from the radio. At this point the turns of
the coiled portion of the cord are (only) about 1/4
apart.
Perhaps it just needs
Ken,
It is not from lack of use, it is very, very stiff.
Best,
DW Holtman
WB7SSN
- Original Message -
From: Ken Kopp [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
Sent: Wednesday, March 26, 2008 8:13 PM
Subject: [Elecraft] MH2 Mic
The MH-2 that I received with my K3 has ... in my
On Wednesday 26 March 2008 18:49, Mike Miller wrote:
I see several guys using the Kenwood MC 43 S mic with K3..
any comparisons. with the MH2. ?
Which is better...looks like they cost about the same
Mike Miller KA5SMA
I've had an original MH2 with my first K2, but didn't like the large
I have a new and unused Elecraft Heil MH2 mic for sale. $75 OBO shipped
CONUS.
tnx 73, Doug -- K0DXV
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub
The MH2 mic has been spoken for.
Thanks -- Doug --K0DXV
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
Anyone have MH2 mic that aren't using and would like to sell? If so please
send details
Thanks
Tim
NZ8J
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub,
If anyone has a MH2 there not using and would like to part
with it, let me know. Would like one in like new condition
if possible. Reply direct to my email address. Have a great day!!
Larry (W6LDA)
___
Elecraft mailing list
Post to:
38 matches
Mail list logo
