On Wed, Apr 16, 2008 at 10:38:40PM -0400, Gene Heskett wrote:
So I need the silver cyanide, a small loop of silver wire I can place
around it for the sacrificial silver, and a few volts and amps to do
the plating. Both are made out of pure un-obtainium out here in the
hills of WV.
A quick
On Thursday 17 April 2008, Erik Christiansen wrote:
On Wed, Apr 16, 2008 at 10:38:40PM -0400, Gene Heskett wrote:
So I need the silver cyanide, a small loop of silver wire I can place
around it for the sacrificial silver, and a few volts and amps to do
the plating. Both are made out of pure
On Thu, Apr 17, 2008 at 03:43:08AM -0400, Gene Heskett wrote:
I think the cyanide solution was for gold plating, and we used a
titanium anode, to avoid polluting the solution. (Which was consumed.)
The solution or the electrode? For either, I always assumed that the anode
should be
On Thursday 17 April 2008, Erik Christiansen wrote:
On Thu, Apr 17, 2008 at 03:43:08AM -0400, Gene Heskett wrote:
I think the cyanide solution was for gold plating, and we used a
titanium anode, to avoid polluting the solution. (Which was consumed.)
The solution or the electrode? For either,
Gene:
There's nice background material on electoplating, electrodeposition,
and such in the Wikipedia. I did enough electroplating in grad school
not to want to go there if I can avoid it.
Did you notice that CoolAmp also markets Conducto-Lube? I don't know if
it would work in your
On Thursday 17 April 2008, Kenneth Lerman wrote:
Gene,
I have a gold ring with my call letters K2EMR that I got as a present from
my parents for my 16th birthday in 1960. It weighs about an ounce and cost
about $16.00
Ken
If it weighs about an ounce, Ken, and cost only $16, that would have been
On Thursday 17 April 2008, Kent A. Reed wrote:
Gene:
There's nice background material on electoplating, electrodeposition,
and such in the Wikipedia. I did enough electroplating in grad school
not to want to go there if I can avoid it.
Did you notice that CoolAmp also markets Conducto-Lube? I
Gentlemen,
While reading the config files for the Mazak I saw the section
where you set up the spindle to 'wrap'. I would like to see that same
capability for the rotary axes.
The C axis on the 5axis sim would work good with the 'wrap'
function. This would work good on a machine I have.
Hi All
I Previously had emc installed via the BDI I have recently tried to
upgrade to emc2,2 . I downloaded the ISO and cut it to a disc
seemingly without a hiccup. I can boot my machine using the live cd
however when I try to install the software the installation hangs at
step 3
On Tue, 2008-04-15 at 20:42 -0700, Kirk Wallace wrote:
I am losing patience with the Bandit on my Shizuoka mill, so I am
...snip
touch off after powering up?
It's time to hit the books, but any advise is appreciated.
Here is what I have reverse engineered so far:
On Wed, 2008-04-16 at 21:37 -0400, John Kasunich wrote:
... snip
It sure looks like a unipolar drive to me. They are probably doing
half-stepping, which would give you the counts per inch that you think
you have.
Power is applied to the two center taps, thru two of the transistors
which
On Thu, Apr 17, 2008 at 01:14:37PM -0700, Kirk Wallace wrote:
http://www.wallacecompany.com/machine_shop/Shizuoka/1-1a.jpg
While it's out I'd meter those 220? ohm carbon composition resistors
surrounded by discolored circuit board. Heat is their enemy and
causes their values to drift
My HobbyCNC board says it is a Unipolar Chopper Control
It does 1/2, 1/4, 1/8, 1/16 microstepping. Uses 6 wire (2 common)
steppers.
C
--- Chris Radek [EMAIL PROTECTED] wrote:
On Thu, Apr 17, 2008 at 01:14:37PM -0700, Kirk Wallace wrote:
On Thu, 2008-04-17 at 14:30 -0700, Curtis W. Moore wrote:
My HobbyCNC board says it is a Unipolar Chopper Control
It does 1/2, 1/4, 1/8, 1/16 microstepping. Uses 6 wire (2 common)
steppers.
C
Thanks Curtis. Thats looks close. Too bad it has a 3 Amp max. I need
around 8 Amps with slightly
Kirk Wallace wrote:
On Thu, 2008-04-17 at 14:30 -0700, Curtis W. Moore wrote:
My HobbyCNC board says it is a Unipolar Chopper Control
It does 1/2, 1/4, 1/8, 1/16 microstepping. Uses 6 wire (2 common)
steppers.
C
Thanks Curtis. Thats looks close. Too bad it has a 3 Amp max. I need
around
On Thu, 2008-04-17 at 18:21 -0400, John Kasunich wrote:
Kirk Wallace wrote:
On Thu, 2008-04-17 at 14:30 -0700, Curtis W. Moore wrote:
My HobbyCNC board says it is a Unipolar Chopper Control
It does 1/2, 1/4, 1/8, 1/16 microstepping. Uses 6 wire (2 common)
steppers.
C
Thanks
Kirk Wallace wrote:
On Thu, 2008-04-17 at 18:21 -0400, John Kasunich wrote:
Do you know your motor's rated current and voltage (not supply voltage,
winding voltage, determined by multiplying the rated winding current by
the winding resistance).
There is no data attached to the motors. I
Ah! Yes. Stopped to think and forgot to start again.
Been there, done that.
Dave
On Apr 17, 2008, at 2:58 PM, Stuart Stevenson wrote:
--
Message: 5
Date: Thu, 17 Apr 2008 12:09:50 -0700
From: Glenn Stewart [EMAIL PROTECTED]
Subject: Re: [Emc-users] Vital
On Thursday 17 April 2008, Dave Engvall wrote:
Ah! Yes. Stopped to think and forgot to start again.
Been there, done that.
Dave
On Apr 17, 2008, at 2:58 PM, Stuart Stevenson wrote:
--
Message: 5
Date: Thu, 17 Apr 2008 12:09:50 -0700
From: Glenn Stewart [EMAIL
Kirk Wallace wrote:
I scoped the driver board inputs again and corrected my signal diagram
on the schematic. The gray traces are the result of the coil input and
it's inhibit. I confirmed this with scoping the far side of the input
optocoupler. I played with the axis speed and noticed the
20 matches
Mail list logo
