[Emc-users] Info Required

2008-09-09 Thread Atif Khalil
Sir,   How do I connect the spindle inverter with MOTENC.My inverter operates with +/-10 Vdc.Kindly advice.        Atif  Khalil. - This SF.Net email is sponsored by the Moblin Your Move Developer's challenge Build the

Re: [Emc-users] Info Required

2008-09-09 Thread Jeff Epler
On Tue, Sep 09, 2008 at 09:47:38AM -0700, Atif Khalil wrote: Sir,   How do I connect the spindle inverter with MOTENC.My inverter operates with +/-10 Vdc.Kindly advice. If you are using the 7525 termination board, you can find a summary of connections in the manufacturer's datasheet:

[Emc-users] Filleting the corners of a pocket

2008-09-09 Thread aaron Moore
Hi I am having problems with tool paths, The tool is not following the tool-path right into the corners, rather it is 'filleting' the corners of a pocket. I am using EMC 2.22 (right out of the box with no tweaks) and SheetCamTNG-V0.0.35.deb, on a gantry style router. I do not know if it a

Re: [Emc-users] Filleting the corners of a pocket

2008-09-09 Thread Leslie Newell
Hi Aaron, With inside corners you will always get a fillet due to the radius of the cutter. You can reduce the problem by using a smaller cutter. If you are cutting a pocket for a sharp edged part to fit into, open the cut operation in SheetCam and go to the cut path tab. Turn on

Re: [Emc-users] Filleting the corners of a pocket

2008-09-09 Thread Kim Mortensen
Aaron, Does Sheetcam show these toolpaths, if not, have you set the G-code that tell the CNC to follow the exact toolpath, because it can round corners to maintain speed/acceleration in certain cases.. unledd you set the exact G-code... cant remember what the number is... Best Regards Kim

Re: [Emc-users] Filleting the corners of a pocket

2008-09-09 Thread Alex Joni
This seems to come up every couple of weeks. http://wiki.linuxcnc.org/cgi-bin/emcinfo.pl?TrajectoryControl Regards, Alex - Original Message - From: aaron Moore [EMAIL PROTECTED] To: EMC userslist emc-users@lists.sourceforge.net Sent: Tuesday, September 09, 2008 9:26 PM Subject:

[Emc-users] New error after upgrade

2008-09-09 Thread Steve Blackmore
Hi Guys - getting a new error after installing upgrading and making my own setup using stepconf. On opening any emc setup, I get an error on the first attempt, the second attempt always succeeds? Even to my untrained eye looking through the error log I spotted the following: 6204.322680] says:

Re: [Emc-users] New error after upgrade

2008-09-09 Thread Alex Joni
Hi, can you post a list of modules loaded? Also, does a reboot cure this issue? I see the first time 6200..6202 RT got up and then back down again, without issues. Only at 6204 (second start?) it got messed up.. sounds like something stayed behind. Regards, Alex - Original Message -

[Emc-users] (fwd) Re: New error after upgrade

2008-09-09 Thread Steve Blackmore
On Wed, 10 Sep 2008 00:37:45 +0300, you wrote: Hi Alex can you post a list of modules loaded? Sorry - I don't know how to do that. Linux/EMC newbie. Can you give me a pointer please. Also, does a reboot cure this issue? No - first attempt at opening any emc config, either mine or sim ones, it

Re: [Emc-users] (fwd) Re: New error after upgrade

2008-09-09 Thread Alex Joni
On Wed, 10 Sep 2008 00:37:45 +0300, you wrote: Hi Alex can you post a list of modules loaded? Sorry - I don't know how to do that. Linux/EMC newbie. Can you give me a pointer please. open a terminal, type lsmod Also, does a reboot cure this issue? No - first attempt at opening any

[Emc-users] New at mailing list, and seeking for some help with 7i43

2008-09-09 Thread Richard Acosta
Hello, my name is Richard, and i´have bought a 7i43 board, wich i hope to use on a home made drilling machine. I´m stuck on the first steps, i have connected this board using parallel port cable, set jumpers according to what manual says, so, now i don't know what else to do. I have been

[Emc-users] Another problem with Hostmot2 and m5i20

2008-09-09 Thread Eric H. Johnson
Sebastian et al, I had just got the stepper outputs working before I went on vacation and am just now getting back to it. I am using Hostmot2, the m5i20 board and SVST8_4 configuration, configured for 2 steppers, 1 pwm and no encoders. I am also using just the patch applied to the most recent

Re: [Emc-users] Another problem with Hostmot2 and m5i20

2008-09-09 Thread Peter C. Wallace
On Tue, 9 Sep 2008, Eric H. Johnson wrote: Date: Tue, 9 Sep 2008 20:28:21 -0400 From: Eric H. Johnson [EMAIL PROTECTED] Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: emc-users@lists.sourceforge.net Subject: [Emc-users] Another problem with Hostmot2 and

Re: [Emc-users] Another problem with Hostmot2 and m5i20

2008-09-09 Thread Eric H. Johnson
Peter, I presumed the selecting of one PWM in the configuration set the direction of the GPIO, as it does for the step and direction outputs for the two steppers in the configuration. Regards, Eric Sebastian is probably the one to ask, but, did you have the driver enable the PWM0? Not the HAL

Re: [Emc-users] Another problem with Hostmot2 and m5i20

2008-09-09 Thread Peter C. Wallace
I presumed the selecting of one PWM in the configuration set the direction of the GPIO, as it does for the step and direction outputs for the two steppers in the configuration. Regards, Eric It should... Is the PWM pin high or low? Did you start with Sebastians HAL file? I know he has

Re: [Emc-users] New at mailing list, and seeking for some help with 7i43

2008-09-09 Thread Kirk Wallace
On Tue, 2008-09-09 at 20:14 -0300, Richard Acosta wrote: Hello, my name is Richard, and i´have bought a 7i43 board, wich i hope to use on a home made drilling machine. I´m stuck on the first steps, i have connected this board using parallel port cable, set jumpers according to what manual