Re: [Flexradio] SDR 1000 with MFJ 998 Intellituner ?

Dan, Can you use TS-2000 CAT commands? You can use the CAT commands out a RS232 port to the tuner. But if all you need is 10 watts out in Tune, when you hit the tune in PowerSDR, it uses a separate power setting from the normal operation and by default is set to 10 watts.. But if you

[Flexradio] Wanted - USB adapter cable , Fire wire cable Griffin Knob , Tuner

I have just purchased an SDR 1000 which I' m going to use with an iMac. I need Windows FP , USB adapter with Parallel port , Griffin Powermate Control Knob , firewire cable and maybe the internal tuner. Please email me . 73 Dan [EMAIL PROTECTED] ___

[Flexradio] Dead RX SDR 1000.

Hi gang. My SDR-1000, is dead, I get noise on the pan and audio, can hear the filter changes as I switch modes. But, even with a XG-2 or IFR connected, I can not get a signal through the unit. Last time I used it, (some time ago) it was a hot RX. I have done the setup, calibration, new data

Re: [Flexradio] Problem with CAT serial port

Doug, Can you provide a bit more detail? 1.) What versions of PowerSDR did you try? 2.) What virtual serial port software packages? 3.) What programs are you using to control PowerSDR? -Tim -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Doug

Re: [Flexradio] 5000A and CW setup

Sam, I had similar problems and have partially resolved them. With paddles and the internal keyer I had problems much as you describe. This was resolved by using an external keyer, in my case either a K1EL WKUSB or a little PicoKeyer. Cabling from the external keyer is set up as with a straight

Re: [Flexradio] Dead RX SDR 1000.

Verify your audio and hardware configuration in the Setup Form first. You should be able to verify that the software is working properly by noting the rise in the noise floor when you place your thumb over the end of the soundcard cable that normally goes to the SDR-1000 To Line In plug. Eric

Re: [Flexradio] I need the link to DDUtilty

svn://206.216.146.154/svn/repos_sdr_hpsdr/trunk/K5FR/DDUtil I don't think the link has changed since I downloaded. 73, Bob -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of FireBrick Sent: Monday, February 11, 2008 6:41 PM To: FlexRadio List Subject:

Re: [Flexradio] Wanted - USB adapter cable , Fire wire cable Griffin Knob , Tuner

This is a global question to all of the folks currently emulating Windows on a Mac running PowerSDR with a SDR-1000 for my edification. Will the proprietary USB-to-Parallel adapter and driver work successfully in this environment? -Tim -Original Message- From: [EMAIL PROTECTED]

[Flexradio] Problem with CAT serial port

I have a problem sending CAT commands to PowerSDR. I have tried various combinations of 1) Four different computers (XP Home and XP Pro) 2) Three different versions of PowerSDR 3) PowerSDR demo mode versus running my Flex-1K. 4) Two different programs for virtual com port. 5)

[Flexradio] I need the link to DDUtilty

I managed to overwrite the new version, 1.3.0 with the old. I have the online help but can't find the link to download the new version. Please and tu ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz

[Flexradio] SDR 1000 with MFJ 998 Intellituner ?

I have recently purchased a Flex Radio SDR 1000 , I would like to use my MFJ 998 intellitunner with it. MFJ has various interfaces cable selections for Yaseu and Icom , I'm currently using it with my Icom Pro III , the MFJ interface cable allows the Pro III to interface with the tuner , it is