flexradio-requ...@flex-radio.biz wrote:
Send FlexRadio mailing list submissions to
flexradio@flex-radio.biz
To subscribe or unsubscribe via the World Wide Web, visit
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
or, via email, send a message with subject
Many besides myself have reported the following problem with the setup-test
function. when the test button is pressed there is no tone coming out of either
speaker. We are all using the delta44 sound card. This function used to work
up until about 3 months ago
Bill Nagle
, there
is a small amount of the motorboating but after going to tx then back rx it is
4
times louder.
I am using a delta44 board into an athlon 2.5g machine
I also have windrm loaded and it works fine
Bill Nagle
[EMAIL PROTECTED]
___
FlexRadio Systems
We have been toying with windrm on the northeast coast and are looking for
some other flexers with which to qso. The audio quality and readability of
this mode far surpasses any other voice mode.
[EMAIL PROTECTED]
Bill Nagle
___
FlexRadio mailing
exists with
either a usb or parallel cable driving the flex. I am thinking somewhere in
the
code there may be an answer to desensitize this thong?
Bill Nagle
[EMAIL PROTECTED]
___
FlexRadio mailing list
FlexRadio@flex-radio.biz
http://mail.flex
Has anyone gotten audio from the newly added svn code from the sub
receiver and if so how?
Bill Nagle
___
FlexRadio mailing list
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archive Link: http
but no power comes out and you canot get it to go back
to run or standby ?
Bill Nagle
___
FlexRadio mailing list
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archive Link: http://www.mail-archive.com
Yes Bob, I think the guys would enjoy reactivating the bin mode on am. the
hilbert transform may simulate the stereo effect.
Bill Nagle w3duq
___
FlexRadio mailing list
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo
So what version of LINUX are we going to use?
I guess billy boy is going to learn the hardway!!!
Bill Nagle
___
FlexRadio mailing list
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archive Link: http
not talking about the mixw and similar app running through the sdr
software but the actual sdr receiver audio.
Bill Nagle
[EMAIL PROTECTED]
Bill Nagle
___
FlexRadio mailing list
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo
Ok, so I changed the svn address to trunk/Source and it downloaded fine.
NOW, after I compile in release mode I cant seem to find where visual 2003
is putting the BIN folder.
Bill Nagle
___
FlexRadio mailing list
FlexRadio@flex-radio.biz
http
What milliseconds should the delta 44 latency be set for?
Bill Nagle
___
FlexRadio mailing list
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archive Link: http://mail.flex-radio.biz/pipermail
--- Forwarded message follows ---
From: Bill Nagle [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Subject:312 question
Date sent: Wed, 24 May 2006 12:33:22 -0400
I recently purchased version 312 of vac and have a question:
I
adding a second
virtual cable to the list in the vac software.
I am setting up a wav file recorder and would like to eliminate the external
audio jumpers currently going from the delta44 speaker out to the onboard
line in jack.
Bill Nagle
[EMAIL PROTECTED
does anyone have a copy of the instructions to change R9 from 1k to 470
ohms to correct the occasional problem where the equipment does not go
back to receive? I need the location of the resistor and which board it is on
also.
Bill Nagle
it momentarily
goes into receive then right back to transmit mode. Unchecking the VOX box
has no effect once it has been checked. The only way to stop it is to exit the
program.
Bill Nagle
than the tdk or other suggestions?
Setup is delta44 on a 2.8gig w/512m ram.
Bill Nagle
[EMAIL PROTECTED]
be left that
way so that you can transmit both mic and wave?
BTW, I finally put the flex into its permanent operating position and am now
driving it with the external audio bank similar to Dave AD does. Superbo!
Bill Nagle
[EMAIL PROTECTED]
what is the procedure for using drm with powersdr? I have purchased the
dream software but how does it interface with flex?
Bill Nagle
when compiling release 19 source, thhe error unable to find setup.vdproj
I suspect this is being caused by a glitch in the sln file?
Bill Nagle
\VsdAdminLicenseDlg.wid'
C:\SDR-1000\Flex-PowerSDR-1-4-5p19\Setup\PowerSDR
Setup.vdproj Unable to build dialog module named
'C:\Program Files\Microsoft Visual Studio .NET
2003\Common7\Tools\Deployment\.\VsdDialogs\1033\VsdLicenseDlg.wid'
Bill Nagle wrote:
when compiling release 19 source, thhe
the problem with release 19 source is that it brings the compiler up into
DEBUG mode. Try switching to RELEASE mode and recompiling.
Bill Nagle
that msadox.dll is not really an error as was explained to me by flex. just
ignore it.
On 25 Mar 2006 at 8:57, Ken N9VV wrote:
Date sent: Sat, 25 Mar 2006 08:57:17 -0600
From: Ken N9VV [EMAIL PROTECTED]
To: Bill Nagle [EMAIL PROTECTED]
Copies
?
Bill Nagle
[EMAIL PROTECTED]
I've been meaning and forgetting to ask who told you the eq notch should be
at 160 hz? All of my broadcast engineer friends say it should be centered
around 250 hz and be around -6-10 db deep.
Perhaps we should start a thread on the forum and get other pinions?
Bill Nagle
[EMAIL PROTECTED]
How do i add a new c file into the powersdr solution in visual studio?
Bill Nagle
will do
On 11 Mar 2006 at 17:20, Robert McGwier wrote:
Date sent: Sat, 11 Mar 2006 17:20:37 -0500
From: Robert McGwier [EMAIL PROTECTED]
To: Bill Nagle [EMAIL PROTECTED]
Copies to: FlexRadio@flex-radio.biz
Subject:Re
Does anyone know how to switch the RELEASE folder to automatic overwrite
each time a build is done? currently the default is if there is a similar
filename
in the folder it leaves it alone.
using c++ .net visual studio 2003
Bill Nagle
[EMAIL PROTECTED]
this in previews 15 and svn 16 ?
Bill Nagle
proposed
solution is to put a small in between relay in the ptt line and have it's
coil
powered by the 12 volts on the LOAD side of the sdr power switch on the
front panel.
Bill Nagle
the monitor hardware performave- no effect. Tried changing
the sdr panadapter to scope mode- no effect.
If I open another app and put it in front of the open sdr app, it cears up.
If I minimize the sdr software it clears up.
Computer is an athlon 1.8gig w/.5 gig ram.
Bill Nagle
headphones .
Bill Nagle
[EMAIL PROTECTED]
Every once in awhile I press a key (not sure which one it is) and the sdr
software becomes about one quarter of its size and the screen now shows
also any open apps that were running. Pressing the escape key brings the
sdr software back in focus.
What IS that magic key?
Bill Nagle
[EMAIL
Hi Jerry:
Could you please send me the code changes to get the sdr1000 panadapter
out to 96khz in release 15?
Thanks,
Bill Nagle
[EMAIL PROTECTED]
Anyone care to share suggested layouts for the buttons on the contour
shuttle device for the sdr1000?
Bill Nagle
[EMAIL PROTECTED]
Am programming the contour shuttle and came across this glitch:
When pressing the key combo ALT+F to narrow the filter, it jumps right down
to VAR1 and then each time you press the combo it changes the cw low/high
limit screens. The same is true if you press CTRL+F to widen the filter.
Bill
ALT+I, K , L dont seem to work on the filters either. This is release 15
Bill Nagle
Does anyone have a graphic of the powersdr.pref keys on the contour
shuttle?
Bill Nagle
[EMAIL PROTECTED]
In version 15 the imd two tone test does not work nor does the power adjust
associated with it. It defaults over to the sweep generator instead.
Bill Nagle
Has anyone else run into this glitch on rev 13-15?
If you set LSB receive to say 4khz then exit the software and start it up
again,
LSB has switched to 6khz.
Bill Nagle
it and make a
suggestion for future rev change. Better yet, could it be made adjustable in
settings easily?
Also, has anyone asked for independent sideband transmit capability for
possible use with digital on one side and voice on the other?
Bill Nagle
[EMAIL PROTECTED]
Do you have a description of the various filters like the hanning default and
what is best for what mode?
Bill Nagle
to add with the digital world in some future sdr
revision.
Your thoughts?
Bill Nagle
In Release 14, if you exit the program from the AM 6khz position with LSB and
USB set to
4khz,
the next time the program is started LSB starts at 6khz while USB remembers its
4khz
setting.
Bill Nagle
%
instead of higher positive peak availability 50%80% on average male voice.
I don't know if this is a creature the alc has hatched since it is NOT present
in
version 12 which shows a nice ratio that changes when the mike phase is
reversed.
Bill Nagle
[EMAIL PROTECTED]
Question on the 100 watt pa: Could we crank up the alc controlled available
peak power a bit by decreasing the bias on either the driver or main
transistors to reduce intermod above 100 watts on ssb ?
Bill Nagle
http://home.ptd.net/~w3duq
I vote for 5 channels of EQ rather than 3.
Bill Nagle
http://home.ptd.net/~w3duq
PS: The scope mode of the display only shows audio waveforms, not
modulation waveforms.
Bill Nagle
http://home.ptd.net/~w3duq
AND audio. This is NOT desirable.
Bill Nagle
[EMAIL PROTECTED]
which is
EXACTLY the way we need it to work.
One question: What is the leveler supposed to be doing?
Bill Nagle
[EMAIL PROTECTED]
more peak power on any given amp on AM.
I can run my SDR at the 25 watt carrier out level and modulate around 200%
in the positive direction (the negative peaks dont cut the carrier off due to
the
operation of the balanced modulator) without any i-m generated.
Bill Nagle
[EMAIL PROTECTED]
Bill
to standby then back to on it recovers.
Bill Nagle
[EMAIL PROTECTED]
from am/lsb/usb to
digl or digu
Bill Nagle
[EMAIL PROTECTED]
Where do I obtain VAC 3.11 ?
Bill Nagle
[EMAIL PROTECTED]
to stop it also
This does not happen on ssb or dsb or fm modes. This happens with two
different delta44 cards.
A cure might be to put a very low frequency highpass filter in the software
(say 10 hz cutoff) wherever the mike input control comes from.
Bill Nagle
[EMAIL PROTECTED]
Seems that the MON button works on SSB but not on AM. It would be very
useful to have it active in AM.
Bill Nagle
http://home.ptd.net/~w3duq
I am trying to set up the DREAM drm encoder using sdr release 12 and
there is no option in transmit profile setup ulldown menu for saving options to
a DRM profile.
Bill Nagle
[EMAIL PROTECTED]
In Version 12 the playback level for wave files is extremely high.
Bill Nagle
[EMAIL PROTECTED]
I get the following s meter upper scale readings with the rx preamp and am
wondering why they are backwards (the higher the gain the lower the
reading). This is with no input signal to the receiver.
off -95db
low -102
med -119
high -124
Bill Nagle
[EMAIL PROTECTED]
Has anyone tried to reverse the mikw phase 180 degrees from within the
flex? I tried reversing it in the delta44 card pullup menu on in3 and in4 but
it
has no effect, i assume because the flex takes over?
Bill Nagle
http://home.ptd.net/~w3duq
sets?
Bill Nagle
[EMAIL PROTECTED]
Be very careful with version 12 when you go to play back a wav file with the
flex recorder. The level is about 10 times the needed level and it may pop
your amp if you dont get to the mox button fast enough.
Bill Nagle
http://home.ptd.net/~w3duq
If I have installed version 12 then make some changes to it and recompile,
when I deploy it from the compiler will it install on top of the originally
installed
version 12? If it does than is it smart enough to see that there is already a
database in there and not overwrite it?
Bill Nagle
The MUTE button has ceased working on preview 12
Also, how does the squelch button work? I dont get any effect in any mode
including fmn.
The new EQ's are amazing,considering that they are only 3 channels.
Behringer could take a lesson for their vx2000 processor.
Bill Nagle
[EMAIL PROTECTED
The problem with mute in version 12 is that it WILL activate yellow when the
software is in STANDBY mode. When you switch the software to ON it will
not go yellow on pushing the mute button.
Bill Nagle
http://home.ptd.net/~w3duq
65 matches
Mail list logo