specs, but 35 C seems to be very
harmless. That's even low enough that it won't hurt if
you touch it. :-)
All processors known to me can take temperatures well over
50 C. Some modern processors can even do more than 80 C
without harm.
Best regards
Oliver
--
Oliver Fromme, secnetix GmbH
everywhere.)
Best regards
Oliver
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29, 85567 Grafing
Dienstleistungen mit Schwerpunkt FreeBSD: http://www.secnetix.de/bsd
Any opinions expressed in this message may be personal to the author
and may not necessarily reflect the opinions of secnetix
this thread might be inappropriate for the
-hackers list. How about moving it to either -hardware
or -chat? (I watch them all, so either is fine with me.)
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29, 85567 Grafing
Dienstleistungen mit Schwerpunkt FreeBSD: http://www.secnetix.de/bsd
Any
),
and it's indeed a CISS device.
Best regards
Oliver
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29, 85567 Grafing
Dienstleistungen mit Schwerpunkt FreeBSD: http://www.secnetix.de/bsd
Any opinions expressed in this message may be personal to the author
and may not necessarily reflect
: DIMM
Set: 1
Locator: DIMM 01
Bank Locator: Not Specified
Type: DDR
Type Detail: Synchronous
Speed: 400 MHz (2.5 ns)
Best regards
Oliver
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29, 85567 Grafing b. M.
Handelsregister: Registergericht
of HP
and Compaq, after which it was probably renamed because of
markting purposes, but it is still the very same thing,
technically.
FreeBSD runs fine on one of those here (a ProLiant DL360).
Best regards
Oliver
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29, 85567 Grafing b. M
online
[...]
Mounting root from ufs:/dev/da0s1a
da0 at ciss0 bus 0 target 0 lun 0
da0: COMPAQ RAID 0 VOLUME OK Fixed Direct Access SCSI-0 device
da0: 135.168MB/s transfers
da0: 17359MB (35553120 512 byte sectors: 255H 32S/T 4357C)
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29, 85567
irrelevant.
For example, if you're planning to run it as DNS server,
router and/or packet filter, then about 128 to 256 MB will
probably suffice. ;-)
Best regards
Oliver
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29, 85567 Grafing b. M.
Handelsregister: Registergericht Muenchen, HRA
than under 6.2-R, for
example NFS (seems to be faster, too, although I haven't
done any benchmarks).
YMMV, of course.
Best regards
Oliver
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29, 85567 Grafing b. M.
Handelsregister: Registergericht Muenchen, HRA 74606, Geschäftsfuehrung:
secnetix
, a small question: I assume that all of those
SATA controllers do have their own BIOS, so I can boot
from them, right? It would be annoying to have to keep
an old PATA disk in that box just to be able to boot.
Thanks!
Best regards
Oliver
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29
. It explains the mechanism
used to maintain the time zone difference (if any)
between FreeBSD and the CMOS clock.
Best regards
Oliver
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29, 85567 Grafing b. M.
Handelsregister: Registergericht Muenchen, HRA 74606, Geschäftsfuehrung:
secnetix
and runs correctly. Only your BIOS doesn't know how
to display it correctly.
Best regards
Oliver
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29, 85567 Grafing b. M.
Handelsregister: Registergericht Muenchen, HRA 74606, Geschäftsfuehrung:
secnetix Verwaltungsgesellsch. mbH, Handelsregister
,
we need to know what controller it is (e.g. vendor ID and
product ID from pciconf -lv output). I think that the
support for intel NICs is very good, thanks to Jack Vogel,
so yours will probably work fine with either the em(4) or
igb(4) driver.
Best regards
Oliver
--
Oliver Fromme, secnetix
that FreeBSD tries to use
SATA-600, which fails because the external case doesn't
support that.
Is there a way to force FreeBSD to use SATA-300 only?
I've searched the mailing lists, but without results.
Best regards
Oliver
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29, 85567
dieter...@engineer.com wrote:
Oliver Fromme writes:
ahcich3: Timeout on slot 0
Is there a way to force FreeBSD to use SATA-300 only?
I've searched the mailing lists, but without results.
man ahci says:
The following tunables are settable from the loader(8
John Baldwin wrote:
On Tuesday, August 14, 2012 9:23:19 am Oliver Fromme wrote:
I've got a small PC that currently has two disks: The
first one is 1 TB with a standard MBR, used to boot FreeBSD,
and the second one is 3 TB with GPT, used as data disk for
FreeBSD (the BIOS doesn't
John Baldwin wrote:
On Monday, September 17, 2012 8:41:09 am Oliver Fromme wrote:
Problem is, the machine doesn't have an EFI BIOS and does
*not* support GPT. So it will use the compatibility MBR
of the GPT, I assume. And MBR isn't able to represent
addresses beyond 2 TB, so
software rendering, then that's
causing your video playback problem. In that case you
should check your Xorg configuration and maybe update
your Xorg video drivers.
Best regards
Oliver
--
Oliver Fromme, secnetix GmbH Co. KG, Marktplatz 29, 85567 Grafing b. M.
Handelsregister: Registergericht
C. G. fun...@hotmail.com wrote:
Oliver Fromme wrote:
Please install the xvinfo tool from ports or packages.
It displays the status of the XVideo extension.
Here is the output of the xvinfo command as you requested :
[root@PC-BSD] ~# xvinfo
xvinfo: Unable to open display
19 matches
Mail list logo