I've followed every advice in /usr/ports/UPDATING
The portmaster -r jpeg* returns No match.
portmaster -r jpeg-7 rebuilds only jpeg-7 no other ports!
After this upgrade my X won't start :-(
Any hints?
Thanks
Leslie
-- snip ---
(II) LoadModule: synaptics
(WW
On Fri, 24 Jul 2009 16:34:35 +0200
Leslie Jensen les...@eskk.nu wrote:
I've followed every advice in /usr/ports/UPDATING
The portmaster -r jpeg* returns No match.
portmaster -r jpeg-7 rebuilds only jpeg-7 no other ports!
After this upgrade my X won't start :-(
Any hints?
Including
/Leslie
of course turn off hald, and run moused.
Unfortunately that did not fix the problem :-(
What do I test next?
/Leslie
do
X -configure
and look at xorg.conf then try fixing something there.
___
freebsd-questions@freebsd.org mailing list
Errors from xkbcomp are not fatal to the X server
(EE) config/hal: NewInputDeviceRequest failed
(EE) config/hal: NewInputDeviceRequest failed
Protocol not supported by server
Do you have
dbus_enable=YES
hald_enable=YES
in your /etc/rc.conf ?
Yes I have
If not: add them, reboot and
Wojciech Puchar skrev:
Errors from xkbcomp are not fatal to the X server
(EE) config/hal: NewInputDeviceRequest failed
(EE) config/hal: NewInputDeviceRequest failed
Protocol not supported by server
Do you have
dbus_enable=YES
hald_enable=YES
in your /etc/rc.conf ?
Yes I have
If
Produces the same result :-(
wouldn't it be better to pkg_delete xserver, make config, turn off hal
dependency and then install. Probably it will work fine then.
Sounds lika a good idea. I'll try it and repport back.
/Leslie
of course turn off hald, and run moused.
Wojciech Puchar skrev:
Produces the same result :-(
wouldn't it be better to pkg_delete xserver, make config, turn off
hal dependency and then install. Probably it will work fine then.
Sounds lika a good idea. I'll try it and repport back.
/Leslie
of course turn off hald, and run
Leslie,
On Fri, May 29, 2009 at 3:06 PM, Leslie Jensen les...@eskk.nu wrote:
of course turn off hald, and run moused.
Unfortunately that did not fix the problem :-(
What do I test next?
Could you paste the output of:
cd /usr/ports/x11/xorg; make missing
--
Glen Barber
Glen Barber skrev:
Leslie,
On Fri, May 29, 2009 at 3:06 PM, Leslie Jensen les...@eskk.nu wrote:
of course turn off hald, and run moused.
Unfortunately that did not fix the problem :-(
What do I test next?
Could you paste the output of:
cd /usr/ports/x11/xorg; make missing
There's no
When I try to startx my screen goes black for a while and then it
returns to the prompt.
At the screen I see this
The XKEYBOARD keymap compiler (xkbcomp) reports:
Warning: Type ONE_LEVEL has 1 levels, but RALT has 2 symbols
Ignoring extra symbols
Errors from
On Fri, 29 May 2009, Leslie Jensen wrote:
When I try to startx my screen goes black for a while and then it returns to
the prompt.
At the screen I see this
The XKEYBOARD keymap compiler (xkbcomp) reports:
Warning: Type ONE_LEVEL has 1 levels, but RALT has 2 symbols
Peter Ulrich Kruppa skrev:
On Fri, 29 May 2009, Leslie Jensen wrote:
When I try to startx my screen goes black for a while and then it
returns to the prompt.
At the screen I see this
The XKEYBOARD keymap compiler (xkbcomp) reports:
Warning: Type ONE_LEVEL has 1 levels, but RALT
On Saturday 02 August 2008 02:30:22 David Gurvich wrote:
Have you loaded all the kernel modules you need and installed
xf86-video-chips?
I am not aware of any kernel modules that i would have to load explicitely.
And, yes, as indicated by the Xorg.log snippet, the chips driver is present.
Hello List,
I got an old TFT that uses a special connector to a CHIPS ct65554 graphics
card. However, although the ct65554 is listed as supported, it is not
recognized by the chips driver. System is FreeBSD 7-Release AMD64. I am
pretty sure that the same xorg.conf worked under i386.
pciconf
Have you loaded all the kernel modules you need and installed
xf86-video-chips?
___
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to [EMAIL PROTECTED]
On Sun, May 01, 2005 at 10:19:17AM -0400, [EMAIL PROTECTED] wrote:
(EE) Failed to load module speedo (module does not exit,0)
(EE) Failed to load module Keyboard (module does not exit,0)
(EE) No input driver matching 'Keyboard'
No core keyboard
Fatal server error:
failed to inititalize
On 5/1/2005 19:49, [EMAIL PROTECTED] wrote:
I just upgraded from 5.3 to 5.4 RC3 via sysinstall from a cd.The
upgrade was successful however, when I try startx I get the
following error:
(EE) Failed to load module speedo (module does not exit,0)
(EE) Failed to load module Keyboard (module does not
[EMAIL PROTECTED] wrote:
I just upgraded from 5.3 to 5.4 RC3 via sysinstall from a cd.The
upgrade was successful however, when I try startx I get the
following error:
(EE) Failed to load module speedo (module does not exit,0)
(EE) Failed to load module Keyboard (module does not exit,0)
(EE) No
I just upgraded from 5.3 to 5.4 RC3 via sysinstall from a cd.The
upgrade was successful however, when I try startx I get the
following error:
(EE) Failed to load module speedo (module does not exit,0)
(EE) Failed to load module Keyboard (module does not exit,0)
(EE) No input driver matching
Hi,
X no more start after a crash with root.
Error Knotify, kdeinit, etc.. pid...
As user all goes well.
What can I do ??
Thanks for your help.
mess-mate
___
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To
On Tuesday, 5 August 2003 at 14:21:38 +0200, mess-mate wrote:
Hi,
X no more start after a crash with root.
Error Knotify, kdeinit, etc.. pid...
If you get that far, X is running. Those error messages are there for
a purpose. Read them.
As user all goes well.
So you're saying that root
21 matches
Mail list logo