On Wed, 25 Feb 2015 20:52:24 +0800, Bill Kenworthy wrote:
I have been using net-misc/spice-gtk (spicy is the executable) to
connect to libvirt vm's. Works well but I cant use CTRL-ALT-Fx to
switch between consoles like you can with virt-manager.
With qemu, you press Ctrl-Alt-space then the F
On 25.02.2015 10:23, Stefan G. Weichinger wrote:
good hint, thanks! I will report back if I find something.
Swapped the cable and also the SATA-socket on the board.
It always gives the same result ...
What is interesting: the HDDs negotiate their NCQ fine:
[2.254804] ata2.00: ATA-8:
This made me recall having to download and alter a Windows SATA Host
Controller driver. For some reason I had to get hold of an 6Gbyte
development .iso to do this (that's Microsoft for you)... Now that was fun
and games!! Basically because the SATA controller driver tried to enable
NCQ (I can't
Hi all,
I have been using net-misc/spice-gtk (spicy is the executable) to
connect to libvirt vm's. Works well but I cant use CTRL-ALT-Fx to
switch between consoles like you can with virt-manager.
Getting my fingers all tangled up yesterday I managed to get it to
switch consoles by accident but I
So this is for my motherboard's (Nehalem - so only one generation before
yours) onboard Intel Host Controller... Only a SATA-2 3Gbit capable device.
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI
Controller (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer
On 25.02.2015 14:18, Bob Wya wrote:
Just out of interest what make is the Host Controller on your
motherboard... Is it a Intel one? Or some crappy addon chipset? Perhaps you
could post the output of lscpi (with lots of - flags - just the Host
Controller bit)?
00:1f.2 SATA controller:
Ahhh,
Quoting from the Intel 6 Series Chipset pdf...
The PCH supports the Serial ATA Specification, Revision 3.0. The PCH
also supports
several optional sections of the Serial ATA II: Extensions to Serial ATA
1.0 Specification,
Revision 1.0 (AHCI support is required for some elements). Please
Switching VTs works for me using ctrl+alt+f#. I can't figure out which
setting is allowing me to do it, if any. Grab keyboard when active
and focused wasn't it. I've had to use this to kill spicy a few times
as if you fullscreen a guest (on my install, at least) you can't get
out.
I wasn't aware
On 25/02/15 21:49, Neil Bothwick wrote:
On Wed, 25 Feb 2015 20:52:24 +0800, Bill Kenworthy wrote:
I have been using net-misc/spice-gtk (spicy is the executable) to
connect to libvirt vm's. Works well but I cant use CTRL-ALT-Fx to
switch between consoles like you can with virt-manager.
On Tue, Feb 24, 2015 at 05:08:50PM -0500, Tom H wrote
# ip a sh dev wlan0
2: wlan0: BROADCAST,MULTICAST,UP,LOWER_UP mtu 1500 qdisc mq state UP
group default qlen 1000
link/ether e8:2a:ea:0f:68:ec brd ff:ff:ff:ff:ff:ff
inet 192.168.1.240/24 brd 192.168.1.255 scope global wlan0
On 25.02.2015 00:55, Bob Wya wrote:
Super obvious question... but can you enable AHCI mode for your SATA
Controller - in the BIOS.
AHCI is enabled in the BIOS, I checked right now.
Do the messages tell us it isn't?
Ah, I see, no NCQ for the SSD ... hmm, right.
Are you using HP supplied SATA
11 matches
Mail list logo
