snip
ARC0846I ML2 TAPES ARE BEING RECYCLED BY ANOTHER HOST
/snip
I do believe what's being asked, is there another LPAR using the HSM CDS'?
If not it soounds like the LPAR/HSM was terminated during a RECYCLE of ML2
and you'll have to zap the control block to clear it.
Jack Kelly
202-502-2390
snip
I am running into a strange situation where occasionally when DFHSM is
recalling ML2 data for A user (not many just one) according to SDSF it
is going to 50% + cpu utilization
/snip
Maybe if you look at the FSR type5's FSRCPU to determine HSM perspective
of CPU usage and FSRTRKW to see
Earlier I posed this query and finally have a resolution. HSM would not
stack SMS and nonSMS volumes on the same tape during AUTODUMP. Problem was
affinity. In the STORAGE GROUPS' DUMP SYSTEM OR SYS GROUP specified
an particular LPAR which gave the SMS volumes affinity to that LPAR. So
SNIP
I'm looking for a book that breaks down the internals of MVS
/SNIP
getting into the ABC series takes a good deal of knowledge and/or
experience. If you're talking more about entry level stuff, something like
MVS: Concepts and Facilities (J. Ranade IBM series)
may be more than enough to
Hold Migration should stop migration after the current dataset. Since I
can't believe that a ML1 DSN is that big, are you sure that the Hold
Migration was received and acted upon by HSM?
Jack Kelly
202-502-2390 (Office)
From:
John Dawes jhn_da...@yahoo.com.au
To:
IBM-MAIN@bama.ua.edu
Date:
snip
Try the HOLD MIGRATION(AUTO) command and see what happens.
/snip
Shouldn't Hold Migration trump (AUTO), in that it should stop ALL
migrations?
Jack Kelly
202-502-2390 (Office)
--
For IBM-MAIN subscribe / signoff / archive
snip
Was it because there were a lot of inexperienced assembler programmers
writing code? Was it because people thought the platform would not last
and treated every program as a throw away? Was it due to limitations in
the assembler itself?
/snip
Having been 'part of that problem', I believe
snip
Could some of it have come about by disassembling to reconstruct or
reverse engineer unavailable source code?
/snip
NO
202-502-2390 (Office)
--
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to
To settle a disagreement, I put a tape without barcode information
into an IBM ATL, d/t 3584 (aka TS3500). The ATL took the tape and put it
in a slot and the display indicated that the VOLSER was Unknown' . So I
would assume that it's not assigned to a Logical Library because it's not
into the libraries web interface and locate the volume,
you can then either assign it a volser, or eject it from the library.
Scott
John Kelly john_j_ke...@ao.uscourts.gov 7/19/2010 9:42 AM
To settle a disagreement, I put a tape without barcode information
into an IBM ATL, d/t 3584 (aka TS3500
Previously I asked if anyone noticed that HSM's PSM always migrates one
DSN from [each] volume that meets the minimum requirement (age and size).
And in fact it does, reply from my PMR:
during PSM HSM processes all of the datasets in the migration queue by
priority order until it reaches the
snip
The ACS routines are written and customized by each installation to
manage their own unique storage requirements. You'll have to hunt down
their source code to see what the routine didn't like in the allocation.
/snip
And to find the current ACS routines use ISMF, opt 7 (AC Selection),
snip
IGD330I ERROR OCCURRED DURING CBRXLCS PROCESSING- *
*VOLUME REQUESTED BY SPECIFIC VOLUME SERIAL IS A SCRATCH VOLUME *
/snip
SMS/OAM does not allow selection of a tape volume in SMS SCRATCH status.
Change it to PRIVATE and try again
Jack Kelly
202-502-2390
If the catalgue is right and there's not a duplicate DSN, I would image
that you need to include a PROCESS(SYS1)
Jack Kelly
202-502-2390 (Office)
From:
larry macioce mace1...@gmail.com
To:
IBM-MAIN@bama.ua.edu
Date:
06/24/2010 08:03 PM
Subject:
Fwd: prob
Sent by:
IBM Mainframe Discussion List
HOLD EXPIREBV should do it.
Jack Kelly
202-502-2390 (Office)
From:
John Dawes jhn_da...@yahoo.com.au
To:
IBM-MAIN@bama.ua.edu
Date:
06/21/2010 01:52 PM
Subject:
STOP EXPIREBV DISPLAY COMMAND
Sent by:
IBM Mainframe Discussion List IBM-MAIN@bama.ua.edu
G'day All,
I issued HSENDCMD EXPIREBV
I would have thought that you'd find it with SMF61 but if not did you try
to see if it was a rename, ie SMF66. Other option would be to check the
VVDS update, SMF60
HTH
Jack Kelly
202-502-2390 (Office)
From:
John Dawes jhn_da...@yahoo.com.au
To:
IBM-MAIN@bama.ua.edu
Date:
06/14/2010 10:54
snip
we are trying to put a gdg to a windows server.
/snip
You loss me there. IF the server(mainframe) is putting to Windows, why
would you send a new DSN. I could see (-1) or (0) but putting (+1) seems
wrong.
Jack Kelly
202-502-2390 (Office)
This is simply a curiosity question. It seems that catalogues are marked
as 'changed' daily, even if not updated?
Most of our catalogues are on nonSMS volumes but those that are on SMS
volumes get backed up by HSM every day even when they haven't been
changed. I am sure about that last
snip
I need to find a PDS member, and I know it starts with QA05. Trouble is,
I don't know the name of the PDS.
/snip
As suggested scan the possible JCL/PROC libraries. If that doesn't find
anything, either RECALL that user's DSN, scan SMF, eg SMF21, maybe
SMF42.6, SMF42.21, or give the
snip
... we have a volume within 3494 library that is not identified by 3494
library ...
/snip
It really looks like the ATL, or at least the TCDB, knows about the
volume, since you did not get:
CBR1064I Command rejected. Volume serial number VOLSER undefined.
What does SMS display or AMS
snip
MODIFY RESOLVER,D
EZZ9294I INCORRECT COMMAND SYNTAX
/snip
Chris,
Appears that it wants DISPLAY instead of just 'D', so
F RESOLVER,DISPLAY
works OK
Jack Kelly
202-502-2390 (Office)
--
For IBM-MAIN subscribe /
I would image that your STORCLAS ACS isn't assigning a STORCLAS to the
request if you code unit=dev#, instead of esoteric. AS I understand
SMSHONOR wants SMS attribute(s)?
Jack Kelly
202-502-2390 (Office)
From:
Tommy Tsui tommyt...@gmail.com
To:
IBM-MAIN@bama.ua.edu
Date:
05/04/2010 10:39 AM
snip
I'm curious how you might be expecting to factor in IDRC compression with
the data stored on the tape? I believe that the BLKCNT represents what is
being stored, not what got sent down the channel.
/snip
I've been reviewing our tape usage with FATS and the TMC BLKCNT is the
number of
I'm not too sure what you have but I do remember that 1.7 to 1.9 (I think)
was a problem with VSAM and UCATs. The jobs would run OK but the data
wasn't available in 1.9. The way that would work is to stop using ...
CAT(...) and use SSA on the 1.7 system. A pain but it works. There have
been
snip
is there any way to dump the RDW
/snip
IDCAMS's PRINT should print the entire record in hex for you. Or if you
have the TTR, then use ZAP.
Jack Kelly
202-502-2390 (Office)
--
For IBM-MAIN subscribe / signoff / archive
snip
Any lessons learned to be shared from those that have implemented PAVs
recently?
/snip
Doesn't look like you're a government agency, so you probably don't have
to deal with VION which is a good thing.
I implemented PAV on our HDS USP-V and it's pretty much like Ted said, ie
simple - once
snip
Is there some way to get from RMF or SMF the total write/read Gb(or Mb) by
tape drive?
/snip
Depending on your requirement and tools available, using the SMF21's
SMF21BRN abd SMF21BWN might be easiest. You could do reports via SORT
fairly painlessly. If you have SAS the SMF74 and SMF30
As others have said, you don't need OAM active unless you're USING SMS
tape drives or objects. Your display of the volumes was from the SCDS but
it's the ACDS that counts. I also couldn't help with DMS but if you're
still having the problem, how about just IEFBR14 allocating a DSN and a
snip
Something is trying to do a SAF call.
/snip
MVS is still up and doing things after you do your 'shutdown', eg your D A
command worked, etc. To stop MVS, do a QUIESCE, after it's 'down' and
removed from whatever
Jack Kelly
202-502-2390 (Office)
From:
Mary Elwood
snip
It would appear both tapes have the same amount of data.
/snip
Dave,
Not only does it look like both tapes have the same amount of data but the
9840D only used 189 feet of the 825 feet available, about 23%. of the
media. Obviously there's a reason for you to keep the 3490 emulation but
snip
IBM's position seems to be that you can hit PFK1, so why do you need a
manual
/snip
and if the tutorial EVER had any usable information, that would be good
advise. The only good thing to say about SDSF's tutorial is that it make
the manual look good.
Jack Kelly
202-502-2390 (Office)
David,
I do believe that you hit it on the head with the 'Unittype(3490)
is specified, which according to the manual nullifies use of the
Capacitymode parameter..' observation. I know that could not get 9840A to
qualify for Capacitymode but I'm not surprise that STK hasn't bellied up
snip
both SMS and non-SMS volumes on the same [dump] tape.
/snip
I took this issue to IBM and it appears that if the StorGroup has multiple
DUMPCLASSes then HSM will not combine SMS and nonSMS volumes on the same
tape. If there is a single DUMPCLASS, then HSM will combine SMS and nonSMS
snip
But the other problem I have is, the only SDSF manual I can find (titled:
SDSF Operation and Customization) is not USER oriented.
/snip
Opinion - The SDSF manual, and for that matter 'support', has always been
awful. To do anything, other than ?, it's pretty much guess or find
someone who
snip
if your tapes are SMS manages then esoterics are not used, period.
/snip
This comment excludes HSM access. HSM does a pre call to SMS and won't
allocate if the tape esoteric is not defined to MVS.
Jack Kelly
202-502-2390 (Office)
Anyone else seen and error updating an PMR? For the last hour, I get the
following message when I attempt to PMR update.
An error has occurred:
The database is currently unavailable. The return code is 606. Please try
again later
Jack Kelly
202-502-2390 (Office)
snip
tried to load the LPARs. .. But I got load failed.
/snip
You didn't indicate if this was your first IPL of the box but it could
definitely be hardware. Did you check to see if your IPL device is
accessible, eg CHP assigned to LPAR, CUs online, etc. Did you try to IPL a
tape, eg, SA dump,
snip
//TEST EXEC PGM=IEFBR14
//TEMP DD UNIT=VIO,SPACE=(TRK,1)
IEF210I JOBNAME# TEST TEMP - UNIT FIELD SPECIFIES INCORRECT DEVICE NAME
/snip
Sounds like someone changed the device that the esoteric VIO was pointing
to in the gen. Since SMS SG seems to allocate to VIO OK, there must be
snip
www-304bluecoat.ibm.com uses an invalid security certificate.
/snip
Here's my response form IBM FeedBack about it. I find that it goes away
after a while but happens mostly with Firefox. When I get it, I go to IE
and get in OK. I had an offline line email from someone else who's had the
snip
i marked the line below and jes2 start successfully :
//* DD DSN=CSQ700.SCSQPROC,DISP=SHR
this line is under proc00 on the jes2 proc, until now it work perferctly
i don't know what change.
/snip
You can save yourself a lot of issues by taking the PROCs out of JCL and
letting JES2
I'm going to IBMLINK via
http://www.ibmlink.ibm.com/ibmlink
I get an Untrusted popup sayin secure certificate only good for
www-304.ibm.com but I'm at https://www-304bluecoat.ibm.com
Jack Kelly
202-502-2390 (Office)
--
For
snip
https://www-304bluecoat.ibm.com
/snip
Guess that it was temporary. It went back to 'normal' after 15 minutes.
I'll send a feedback to IBM to see what it was.
Jack Kelly
202-502-2390 (Office)
--
For IBM-MAIN subscribe /
I will cross post this to the TCP List as soon as I re-figure out how to.
I have three FTPs running on a one stack TCP on a 1.9 system. Good old FTP
21 is still churning and ftps (open ftp, IBM ported ftp, or whatever it's
called) is working and listening on port 22. Since everything is
snip
So what i want to do is copy the IODF and place it on the COD res pack
WITHOUT bringing up the COD(as it wouldn't work anyway)
/snip
Since the IODF is VSAM you'll need it catalogued. I find that the Alias
HLQ to the COD catalog is the easiest way, just like you do with
ServPac,etc. Then
snip
I meant to add that with the exception of SYS1, a VSAM dataset can only
exist in 1 catalog at a time.
/snip
I must have missed this one too, when did IBM remove PAGE HLQ from this
list?
I thought that the original OP wanted to keep the COD separate from his
running system, so I thought
snip
DEF PAGESPACE(NAME(PAGE.LIH1.COMMON) -
FILE(MVSPG3) VOL(MVSPG3) RECATALOG) -
CAT(CATALOG.ICF.newmastercat)
/snip
I know that I have SYS1 HLQ page DSNs, rather than PAGE, but I haven't
been able to simple recatalog the page DSNs since 1.7, I also don't
understand how you could
snip
2) JSTL = 86400 seconds = TIME=1440
3) SWTL is x' 0D286880'
/snip
I can't make the arithmetic work for x'0D286880' either but I thought
that I'd offer
4) OMVS task is exempt from JWT
Also TIME=NOLIMIT is exempt, as is 1440. I'm not sure if time=1440 still
doesn't write SMF records
snip
According to my understanding, we need a CUADD for every controller on the
FICON
/snip
I'm not sure what a SL8500 ATL with STK 1 drives is but your
comments seem to indicate that each CU is a tape drive? Is each STK 1000
drive a contol unit and do you have the same CHP going to all
snip
I don't know how to go about measuring this to determine if it is a
problem
/snip
A good place to start is the 'f catalog,.' commands. they will tell
you lots of good things about how busy your catalogues are and their
performance.
Jack Kelly
202-502-2390 (Office)
snip
Windows or RedHat Linux side of things and then taking those dumps
(TS7700) offsite
/snip
Jim
We're using a 3584 with LTO and 3592 tape drives and the little people are
using Tivoli to backup/dump data to the LTOs. We haven't taken it offsite
yet, other than to Iron Mountain. I can put
snip
I don't get it. 1000MB is 1GB, which is well under 65536 tracks (4369
cylinders). The actual file is under 100 cylinders.
/snip
I thought that SMS combined the primary and all of the secondaries to make
the total allocation, not just the primary, Does it fail is you just give
it a
snip
physical restore. Here is the entire message along with the diagnostic
code:
DR866I (001)-SB213(01), UNABLE TO RENAME VTOC INDEX ON VOLUME SBB103
DIAGNOSTIC INFORMATION: 040E0033
/snip
Sounds like you already have a IX by that name. the reason code indicates:
Check caller's authority and
snip
I am puzzled by the message ADR866I
/snip
Hopefully that was a logical restore not a physical one. What was the
diagnostic codes?
Jack Kelly
202-502-2390 (Office)
--
For IBM-MAIN subscribe / signoff / archive access
on the HMC SAD display.
-Original Message-
From: IBM Mainframe Discussion List [mailto:ibm-m...@bama.ua.edu] On
Behalf Of John Kelly
Sent: Wednesday, February 03, 2010 3:10 PM
To: IBM-MAIN@bama.ua.edu
Subject: Re: Tape drive disconnect time issue
snip
some of those STK drives were faster
I'm bringing up an 3584 ATL with some 3592 drive on two control units. I
noticed that when I allocate a tape the drives are allocated serially from
low to high, ie control unit zero, device zero then on then ... and then
control unit one device zero,
I couldn't find anything in the
I have an old STK tape system ( ten 9840's in 3490 emulation mode inside a
9740. Each drive ESCON point to point) , that will hopefully go away but
I have an issue with HSM dump running longer than expected. The problem
appears disconnect time. During the HSM dumps, we're using four
. Have you
looked at the path?
-Original Message-
From: IBM Mainframe Discussion List [mailto:ibm-m...@bama.ua.edu] On
Behalf Of John Kelly
Sent: Wednesday, February 03, 2010 12:51 PM
To: IBM-MAIN@bama.ua.edu
Subject: Tape drive disconnect time issue
I have an old STK tape system ( ten
snip
I translated and ACTIVATE'd twice
/snip
have you Validated it and did you get the 'object created' message?
Jack Kelly
202-502-2390 (Office)
--
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to
snip
IGGN505A Specify unit for SYS1.IBM.PARMLIB on SYSR1 or cancel === then
I checked our SYS1 datasets and SYS1.PARMLIB is the only one cataloged to
volser **. Maybe because SYSR1 is not resolved yet. You can try
this. now
/snip
Appear like the DSN is changing. Initially it was
snip
:Currently in Top Secret each user has some institution defined data
that we use for various things. There is a call interface called TSSCAI
that we can call from Cobol programs to retrieve this data
unsnip
There are lots of routines running around that extract RACF fields, try
CBT
snip
Now, how do I override that? Is there a JCL parameter?
/snip
As other have said, use a different MgmtClas (MC) is you can or make the
PDSe nonSMS and piss off everyone. Lots of time you can't allocate with a
different MC but you can ALTER the DSN after it's allocated.
Jack Kelly
snip
debug1: SSH2_MSG_KEXINIT sent
Connection closed by x.x.x.x
/snip
I haven't been following this thread too closely but this seems like the
client was waiting for the server and the server terminated the session.
Have you used sshd -d to get the server's debug options? As an aside,
when
snip
sysouts have a status user
/snip
I tend to find that 'user' in this case means a sysout 'hold'. In my
cases, this is caused by an error in handling the sysout, usually a PSF
issue. Releasing the job doesn't release the sysout, I have to release the
individual sysout. HTH.
Jack Kelly
snip
You may need to vary the console device off/on and V CONSOLE to get it
back however
/snip
I can't disagree with the orderly shutdown but I've never had to do
anything to the console PCs, eg shutdown TN3270 emulator, with an IPL. And
I even have the Secure Agent emulator, using 'unsecure'
snip
Check out the TAPEUTILIZATION command option in HSM. You can use the
CAPACITYMODE option or depending on how back-level your HSM is you can
set percentfull to +100%.
/snip
I didn't think that CAPACITYMODE would work for anything other than 3590
emulating 3490. I know that it didn't do too
The HSM Guide states:
Volumes associated with copy pools are not stacked with non-copy pool
volumes. Outside of copy pool associated volumes, dumps of SMS-managed and
non-SMS-managed volumes can exist on the same dump tape.
which would leave me to believe that SMS and nonSMS volumes would be
snip
Yes, I quite definately have both SMS and non-SMS volumes on the same
tape. What level of HSM are you running, at what PUT level?
/snip
Scott,
First, thanks for the response, glad to know that there's light at the end
of the tunnel.
I'm running the 1.9 HSM but my maintenance is around
snip
If you were unable to implement CA-JOBTRAC V11 into your production
environment, then what did you do?
/snip
At this account, we got tired of trying to get it to work and dropped
JobTrac. We were lucky in that job scheduling was minimal and the rest
we put into MVS/OPS.
Jack Kelly
snip
RACF in the facility class called STGADMIN.IGC.**
/snip
I do believe that it's a typo or a hybrid of IGG and IDC. Audit it and if
nothing, delete it.
Jack Kelly
202-502-2390 (Office)
--
For IBM-MAIN subscribe / signoff /
snip
Our solution was to define a separate set of non-library drives that were
always offline at our home installation.
/snip
Wouldn't you have a problem with SMS assigning to the non-library drives
at the DR or do you use different ACS' or unitnames at DR?
Jack Kelly
202-502-2390 (Office)
I believe that this type of problem was discussed a month or so ago, so
you should be able to find more info in the archive. Basically you'll need
to use IEH-eyeball and see what is using CSA, luckily it's not ECSA. I
assume that you already have VSM TRACK on for CSA. Once you find out
what's
snip
From REXX you can internally issue the LISTC and capture and parse the
output, and the REXX DATE function should be able to supply the rest.
/snip
If you have RMM you can just use their REXX/CLIST interface to get the
date. TMS you're out of luck, you'll have to parse the LISTC output. But
snip
Your email address bounced when I tried to send you the SMS DATACLAS we
are using.
/snip
I'm not too sure what good a DATACLASS ACS routine will be, unless it's
for the media or to tell the SC and SG routine what to do. If it's non
SMS, the SC routine will have to make the decision, not
snip
It should be noted that early IPL messages can be written to the HMC
system console in addition to/or instead of the z/OS NIP console. While
the HMC
system console has a number of usability problems, it does allow scrolling
backward to see messages.
/snip
I'll bite, how do you make
snip
I have a problem with the console device; is it possible to unpin the
device associated to the console??
/snip
You'll need to delete the unused console first. Members are
SYS1.SAMPLIB(IEARELCN) MCS CONSOLE
SYS1.SAMPLIB(IEARELEC) EMCS CONSOLE
Jack Kelly
202-502-2390 (Office)
snip
But then, I blame Extra! for most things, when I have to use it.
/snip
You really have to know what bad is to make a comparison. I use to think
Extra was bad but they this account went to Secure Agent's 3270 emulator.
It REALLY is the bottom of the dung heap!
Jack Kelly
202-502-2390
I made a TAPECOPY of an ML2 tape. I don't remember why but a month later I
made another TAPECOPY of the same ML2 tape. i assumed that HSM would
delete the first one, obviously I'm wrong. I did find a sentence that For
duplex tapes only, the tape volume exit ARCTVEXT is invoked, if active, to
I didn't see my response, so I've sent it again. If a dupe, I apologize.
snip
SYS1.VTOCIX.SYBSS1
/snip
Seems like you missed a 'V' in the DSN, it should be SYS1.VTOCIX.VSYBSS1
instead of SYS1.VTOCIX.SYBSS1
|__
snip
SYS1.VTOCIX.SYBSS1
/snip
You missed a 'V' in the DSN, it should be SYS1.VTOCIX.VSYBSS1
|__
Jack Kelly
202-502-2390 (Office)
--
For IBM-MAIN subscribe / signoff / archive access
snip
but there?s no further info on HOW to use DATACLAS to bypass sms.
/snip
There is no way to bypass SMS with Dclass unless there's a check in the
StorClas ACS to check on the Dclass name. I believe that your quote
indicates that you can use Dclass with non SMS DSN but not the other
classes.
snip
The main problem is that the second partition to come up does not have
TCP/IP connectivity
/snip
not to get involved in the TP portion of this thread, is the CHP online
and accessible to the second partition?
Jack Kelly
202-502-2390 (Office)
snip
Is there a utility where I can give it a list of dataset names and it can
give back some JCL that could have been used to define that file?
/snip
The REXX suggested is probably the easiest way, especially if you put in
a LISTDSI. That will give you most of the parameters that you need to
snip
But when I request a particular number of cylinders, some busybody
component (sometimes?) adjusts the requested number downward by the ratio
of 3380 cylinder size to 3390 cylinder size.
/snip
That certainly sounds like the Default Device Geometry in the SMS Base
Configuration.
Jack
This is a curiosity question. I noticed that I have one or two datasets
daily that get migrated during PSM that have one track and the minimum age
(via MgmtClas criteria). There are numerous other datasets that have much
larger allocation and longer age that aren't migrated. PSM has no trouble
snip
Lack of ML1 space? What do the HSM migration logs say? Hint MSGARC0734I If
SMS managed, what is the MGMTCLAS and the attributes assigned?
/snip
These DSN go directly to ML2 (which I should have stated) so ML1 isn't an
issue.
Since there isn't any errors, there's no msgARC0734I
SMS
snip
The Mainstar code was fixed before GA. Frankly, since SDS provided also
provided a fix, I would consider this a user error.
/snip
Paranoia seems to have raised its head. I didn't see anything accusatory
in this thread and how many times have 'users issues/errors' been involved
in
snip
Does the Management class for these datasets require a Backup and does
that backup exist?
/snip
Yes, backup is required and was done, and current (exists), two weeks
before the DSN gets migrated.
Jack Kelly
202-502-2390 (Office)
This is from z/OS V1R9.0 DFSMShsm Storage Administration Guide
(SC35-0421-06) page 65.
/snip
John thanks for the thought but I think that's talking about Interval
Migration Processing and not so much about PRIMARY SPACE MANAGEMENT.
Jack Kelly
202-502-2390 (Office)
snip
DELETE (Vxx) VOLUMEENTRY PURGE
/snip
is trying to delete a volcat entry and should require update.
Seems like the operator should be doing a RMM 'delvol remove' if
Scratch
Jack Kelly
202-502-2390 (Office)
--
When defining DSECT entries, I always find it better to let the assembler
figure out lengths,ie use the length of the generated WTO to define the
length DSECT entry
sDetailmsg wto text=,routcde=(11),mf=l
endmsg ds 0H
then
Detailmsg ds cl(endmsg-sDetailmsg)
then you don't
snip
Any ideas how to find who has the dataset?
/snip
have you looked at SMF14 and/or SMF15 if you collect them or SMF42.6 if
the DSN is SMS around the time of the step failure?
Jack Kelly
202-502-2390 (Office)
--
For IBM-MAIN
snip
IEC030I B37-04,IFG0554A,DFHSMY,DFHSMY,ARCPDOX,9BEB,SMP103,HSM.HSMPDOXY
/snip
Willie it certainly doesn't look like you've done too much HSM work.
Message seems WAD for what you've said that you're doing. What you may
have to look at for is the journal and automation that you have with that.
snip
There is a non-reentrant program which, when executed via JCL from an
authorized library, fails with a S0C4.
/snip
As a debugging tool can you determine which subpool the module is loaded
into (that should clear up the non reentrant [et al] too) and what reason
code is the AB/S0C4
snip
HSEND FREEVOL MVOL(HSM501) AGE(0) TARGETLEVEL(Ml2)
/snip
If you don't use AGE(0) with SMS DSN, then the management class for each
SMS data set is used to determine whether the migration copy is moved to
another volume.
Jack Kelly
202-502-2390 (Office)
I'm at a lost about several things that you mention (other apparently
understood), maybe you could clarify?
snip
drains the lpar, goes to the HMC (hardware management console) , finds the
?activate? colophon for that lpar, selects it
/snip
I don't understand how activate would work unless part
snip
Can the HSM.Backtape and ML2 tapes be unencrypted while the off-site
HSM.COPY.** tapes are encrypted?
/snip
From what RS indicated, it sounds like the T9840D device is either encrypt
or not (I don't know what those devices are like) which would mean that
you'd have to segregate allocation
snip
He has included the Java in the JCL
//SMPCPATH DD PATH='/usr/lpp/smp/classes/'
//SMPJHOME DD PATH='/usr/lpp/java/J1.4/'
/snip
I haven't looked up the messages but J1.4 seems old for a 1.9 system. I'm
on 1.9 and it J1.6. Don't know if that makes a difference but
Jack Kelly
snip
is there a way to keep job output only if the RC 0 ?
/snip
What I've done is have a unique purge sysout class and then review the
job at end of execution (eg JES3 IATUX19/72 or JES2 exit51, maybe exit40)
to check the max return code and change the class then.
Jack Kelly
202-502-2390
snip
The DSORG is ? or NONE.
/snip
it is wise to have a default dataclass that assigns a dsorg=ps so you
don't have this problem.
Jack Kelly
202-502-2390 (Office)
--
For IBM-MAIN subscribe / signoff / archive access
snip
We are getting the following sequence in our syslog several times a
day:
/snip
The IEF196I is just an echo message, which I turn off with MPF and
TSS7000I is a Top Secret audit trail type of message.
Jack Kelly
202-502-2390 (Office)
1 - 100 of 226 matches
Mail list logo
