Re: [PATCH 2/2] memory: omap-gpmc: Add Kconfig option for debug

On Wednesday 06 January 2016 10:55:51 Ivaylo Dimitrov wrote: > > > On 6.01.2016 00:49, Tony Lindgren wrote: > > > >Suggested fix below, please test and reply with your Tested-by's if > >it solves the problem so we may still be able to get this into v4.4. > > > >Regards, > > > >Tony > > > >8<

[PATCH 0/2] DRA72/DRA74: Add 2 lane support

Add driver modifications in pci-dra7xx to get x2 mode working in DRA72 and DRA74. Certain modifications is needed in PHY driver also which will be sent as a separate series. Certain board modifications has to be done in order to test x2 mode in dra72-evm. These patches were created on pci next.

[PATCH 1/2] phy: ti-pipe3: get tx and rx MEM resource

get tx and rx MEM resource since this has to be used to configure for DRA72x to work in X2 mode. Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Sekhar Nori --- drivers/phy/phy-ti-pipe3.c | 27 +++ 1 file changed, 27 insertions(+)

Re: [PATCH 2/2] memory: omap-gpmc: Add Kconfig option for debug

On 6.01.2016 00:49, Tony Lindgren wrote: Suggested fix below, please test and reply with your Tested-by's if it solves the problem so we may still be able to get this into v4.4. Regards, Tony 8< --- From: Tony Lindgren Date: Tue, 5 Jan 2016 12:04:20 -0800

[PATCH 2/2] pci: host: pci-dra7xx: Enable x2 mode support

Perform syscon configurations to get x2 mode to working in DRA74x and DRA72x. Also add a new compatible string to dfferentiate DRA72x and DRA74x, since b1c0 mask is different for both these platforms. Signed-off-by: Kishon Vijay Abraham I ---

[PATCH 1/2] pci: host: pci-dra7xx: use "num-lanes" property to find phy count

use "num-lanes" property to find phy count instead of the number phy-names property. Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Sekhar Nori --- drivers/pci/host/pci-dra7xx.c | 23 +++ 1 file changed, 11 insertions(+), 12

[PATCH 0/2] dra72: add support for PCIE 2 lane mode

dra72 reuse the USB PHY for the PCIe 2n lane. So in order for PCIe x2 mode to work in dra72, certain special configuration has to be made in USB PHY. This patch series adds those configurations. In order to enable PCIe x2 mode in DRA72, USB should be disabled. Certain board modifications has to

[PATCH 2/2] phy: ti-pipe3: configure usb3 phy to be used as pcie phy

DRA72 uses USB3 PHY for the 2nd lane of PCIE. The configuration required to make USB3 PHY used for the 2nd lane of PCIe is done here. Signed-off-by: Kishon Vijay Abraham I --- Documentation/devicetree/bindings/phy/ti-phy.txt |2 ++ drivers/phy/phy-ti-pipe3.c

Re: [PATCH 2/2] pci: host: pci-dra7xx: Enable x2 mode support

On Wed, Jan 06, 2016 at 04:19:53PM +0530, Kishon Vijay Abraham I wrote: > Perform syscon configurations to get x2 mode to working in DRA74x and > DRA72x. Also add a new compatible string to dfferentiate > DRA72x and DRA74x, since b1c0 mask is different for both these platforms. > > Signed-off-by:

Re: [PATCH 2/2] phy: ti-pipe3: configure usb3 phy to be used as pcie phy

On Wed, Jan 06, 2016 at 04:29:08PM +0530, Kishon Vijay Abraham I wrote: > DRA72 uses USB3 PHY for the 2nd lane of PCIE. The configuration > required to make USB3 PHY used for the 2nd lane of PCIe is done > here. > > Signed-off-by: Kishon Vijay Abraham I > --- >

Re: [PATCH 1/3] ARM: dts: omap5-board-common: enable rtc and charging of backup battery

On 01/06/2016 02:13 AM, Laxman Dewangan wrote: > > On Wednesday 06 January 2016 01:12 PM, H. Nikolaus Schaller wrote: >> Hi, >> >> Am 06.01.2016 um 00:40 schrieb Nishanth Menon : >> >>> On 01/05/2016 06:01 AM, H. Nikolaus Schaller wrote: +rtc { +

Re: OMAP4430 power management support

On 01/06/2016 08:22 AM, Frank Jenner wrote: > Hello, > > I am working on trying to enable power management features on a > product that was based on the OMAP4430 SoC and the mainline 3.14 > kernel. In particular, I am interested in enabling Smart Reflex/AVS > and frequency scaling (via cpufreq)

OMAP4430 power management support

Hello, I am working on trying to enable power management features on a product that was based on the OMAP4430 SoC and the mainline 3.14 kernel. In particular, I am interested in enabling Smart Reflex/AVS and frequency scaling (via cpufreq) functionality. I have attempted to use the following

[PATCH] clk: move the common clock's to_clk_*(_hw) macros to clk-provider.h

to_clk_*(_hw) macros have been repeatedly defined in many places. This patch moves all the to_clk_*(_hw) definations in the common clock framework to public header clk-provider.h, and drop the local definations. Signed-off-by: Geliang Tang --- drivers/clk/clk-composite.c

Re: OMAP4430 power management support

I dont' know if it helps, but I struggeled with this too. With my DM3730 (OMAP 3630), I had to enable Device Drivers->Adaptive Voltage Scaling Class Support which enables CONFIG_POWER_AVS, a requirement for POWER_AVS_OMAP. Once I did that, I was able to get AVS Class 3 working on my DM3730 using

Re: OMAP4430 power management support

On Wed, Jan 6, 2016 at 9:26 AM, Nishanth Menon wrote: > On 01/06/2016 08:22 AM, Frank Jenner wrote: >> Hello, >> >> I am working on trying to enable power management features on a >> product that was based on the OMAP4430 SoC and the mainline 3.14 >> kernel. In particular, I am

Re: OMAP4430 power management support

On 01/06/2016 09:05 AM, Frank Jenner wrote: > On Wed, Jan 6, 2016 at 9:26 AM, Nishanth Menon wrote: >> On 01/06/2016 08:22 AM, Frank Jenner wrote: >>> Hello, >>> >>> I am working on trying to enable power management features on a >>> product that was based on the OMAP4430 SoC and the

Re: [PATCH 2/2] memory: omap-gpmc: Add Kconfig option for debug

Hi, On Tue, Jan 05, 2016 at 02:49:29PM -0800, Tony Lindgren wrote: > Commit 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug") > unified the GPMC debug for the SoCs with GPMC. The commit also left > out the option for HWMOD_INIT_NO_RESET as we now require proper timings > for GPMC

Re: [PATCH 2/2] memory: omap-gpmc: Add Kconfig option for debug

On 6.01.2016 19:47, Tony Lindgren wrote: * Sebastian Reichel [160106 09:41]: Hi, On Tue, Jan 05, 2016 at 02:49:29PM -0800, Tony Lindgren wrote: Commit 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug") unified the GPMC debug for the SoCs with GPMC. The

Re: [PATCH 2/2] memory: omap-gpmc: Add Kconfig option for debug

* Sebastian Reichel [160106 09:41]: > Hi, > > On Tue, Jan 05, 2016 at 02:49:29PM -0800, Tony Lindgren wrote: > > Commit 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug") > > unified the GPMC debug for the SoCs with GPMC. The commit also left > > out the option for

Re: [PATCH 2/2] memory: omap-gpmc: Add Kconfig option for debug

* Ivaylo Dimitrov [160106 10:01]: > > Unfortunately, it seems there is more to be fixed. It booted several times > to the userspace, but after a couple of shutdowns, rootfs became corrupted > again. I flashed, installed linux 4.4, but the same happened after the

OMAP3630-ISP and MT9P031 Device Tree Help

I am trying to setup the device tree to enable a parallel camera interface as found on the LPD Dev Kit. The instructions I am using for the basis are: https://alaganraj.wordpress.com/2015/08/08/beagleboard-xm-camera-li-5m03-mt9p031-support-with-device-tree/ It I get the same results when I

Re: [PATCH 2/2] memory: omap-gpmc: Add Kconfig option for debug

Hi, On 6.01.2016 20:26, Tony Lindgren wrote: Hmm. Care to verify that your onenand really gets detected at 83 MHz like your earlier logs show? Below is a patch that should show it. before the corruption appeared, I looked a couple of times in syslog and the freq there was 83MHz. Including

Re: OMAP4430 power management support

On 01/06/2016 10:02 AM, Adam Ford wrote: > I dont' know if it helps, but I struggeled with this too. > > With my DM3730 (OMAP 3630), I had to enable Device Drivers->Adaptive > Voltage Scaling Class Support which enables CONFIG_POWER_AVS, a > requirement for POWER_AVS_OMAP. > > Once I did that, I

Re: [PATCH 1/3] ARM: dts: omap5-board-common: enable rtc and charging of backup battery

On Wed, Jan 6, 2016 at 8:36 AM, Nishanth Menon wrote: > On 01/06/2016 02:13 AM, Laxman Dewangan wrote: >> >> On Wednesday 06 January 2016 01:12 PM, H. Nikolaus Schaller wrote: >>> Hi, >>> >>> Am 06.01.2016 um 00:40 schrieb Nishanth Menon : >>> On 01/05/2016 06:01

Re: OMAP4430 power management support

Any chance you can define what you mean by 'issues' and 'old'? Logic PD (my daytime employer) uses AVS 3 in their custom Linux distribution. If that's going to be a problem, I would like to notify some people there. adam On Wed, Jan 6, 2016 at 1:12 PM, Nishanth Menon

Re: [PATCH 2/2] memory: omap-gpmc: Add Kconfig option for debug

* Pali Rohár [160106 01:06]: > On Wednesday 06 January 2016 10:55:51 Ivaylo Dimitrov wrote: > > On 6.01.2016 00:49, Tony Lindgren wrote: > > > > > >Suggested fix below, please test and reply with your Tested-by's if > > >it solves the problem so we may still be able to get

Re: [PATCH 1/3] ARM: dts: omap5-board-common: enable rtc and charging of backup battery

* H. Nikolaus Schaller [160106 08:48]: > Hi Tony, > > Am 06.01.2016 um 17:41 schrieb Tony Lindgren : > > > Hi, > > > > * H. Nikolaus Schaller [160106 00:12]: > >> Am 06.01.2016 um 02:00 schrieb Tony Lindgren : > >>>

Re: [PATCH 1/3] ARM: dts: omap5-board-common: enable rtc and charging of backup battery

Hi, * H. Nikolaus Schaller [160106 00:12]: > Am 06.01.2016 um 02:00 schrieb Tony Lindgren : > > > > Also I'm not seeing just zeroes coming from RTC after typing hwclock > > on omap5-uevm. It's working on x15 though. > > > > Nikolaus, is hwclock command

Re: [PATCH 2/2] memory: omap-gpmc: Add Kconfig option for debug

Hi, On Tue, Jan 05, 2016 at 02:49:29PM -0800, Tony Lindgren wrote: > From: Tony Lindgren > Date: Tue, 5 Jan 2016 12:04:20 -0800 > Subject: [PATCH] ARM: OMAP2+: Fix onenand rate detection to avoid filesystem > corruption > > Commit 63aa945b1013 ("memory: omap-gpmc: Add Kconfig

Re: [PATCH 1/3] ARM: dts: omap5-board-common: enable rtc and charging of backup battery

Hi Tony, Am 06.01.2016 um 17:41 schrieb Tony Lindgren : > Hi, > > * H. Nikolaus Schaller [160106 00:12]: >> Am 06.01.2016 um 02:00 schrieb Tony Lindgren : >>> >>> Also I'm not seeing just zeroes coming from RTC after typing hwclock >>>

Re: [PATCH 1/3] ARM: dts: omap5-board-common: enable rtc and charging of backup battery

Hi Tony, Am 06.01.2016 um 02:00 schrieb Tony Lindgren : > * Nishanth Menon [160105 15:40]: >> On 01/05/2016 06:01 AM, H. Nikolaus Schaller wrote: >>> tested on OMP5432 EVM >>> >>> Signed-off-by: H. Nikolaus Schaller >>> --- >>>

Re: [PATCH 1/3] ARM: dts: omap5-board-common: enable rtc and charging of backup battery

On Wednesday 06 January 2016 01:12 PM, H. Nikolaus Schaller wrote: Hi, Am 06.01.2016 um 00:40 schrieb Nishanth Menon : On 01/05/2016 06:01 AM, H. Nikolaus Schaller wrote: + rtc { + compatible = "ti,palmas-rtc"; +

Re: [PATCH v3] PCI: hosts: mark pcie/pci (msi) irq cascade handler as IRQF_NO_THREAD

Hi Grygorii, On Thu, Dec 10, 2015 at 09:18:20PM +0200, Grygorii Strashko wrote: > On -RT and if kernel is booting with "threadirqs" cmd line parameter > pcie/pci (msi) irq cascade handlers (like dra7xx_pcie_msi_irq_handler()) > will be forced threaded and, as result, will generate warnings like:

Re: Nokia N900: u-SD card in v4.2+

Hi, On Thursday 07 January 2016 02:16 AM, Pavel Machek wrote: > Hi! > > In v4.1, both internal MMC and u-SD cards work ok. > > In v4.2, only the internal MMC is detected. In v4.3, not even internal > MMC works. In v4.4, only the internal MMC is detected. > > Does it work for you? Any patches?

Re: [PATCH 2/2] pci: host: pci-dra7xx: Enable x2 mode support

Hi, On Wednesday 06 January 2016 07:43 PM, Rob Herring wrote: > On Wed, Jan 06, 2016 at 04:19:53PM +0530, Kishon Vijay Abraham I wrote: >> Perform syscon configurations to get x2 mode to working in DRA74x and >> DRA72x. Also add a new compatible string to dfferentiate >> DRA72x and DRA74x, since

Re: OMAP4430 power management support

On 01/06/2016 01:44 PM, Adam Ford wrote: > Any chance you can define what you mean by 'issues' and 'old'? > AVS class recommendation is AVS Class 1.5 for DM3730. If one does not follow the recommendation, then the result will be that some devices may not function OR fail in some unpredictable

Re: [PATCH 1/3] ARM: dts: omap5-board-common: enable rtc and charging of backup battery

On 01/06/2016 01:34 PM, Rob Herring wrote: > On Wed, Jan 6, 2016 at 8:36 AM, Nishanth Menon wrote: >> On 01/06/2016 02:13 AM, Laxman Dewangan wrote: >>> >>> On Wednesday 06 January 2016 01:12 PM, H. Nikolaus Schaller wrote: Hi, Am 06.01.2016 um 00:40 schrieb Nishanth

Nokia N900: u-SD card in v4.2+

Hi! In v4.1, both internal MMC and u-SD cards work ok. In v4.2, only the internal MMC is detected. In v4.3, not even internal MMC works. In v4.4, only the internal MMC is detected. Does it work for you? Any patches? (I do have hack in the dts to disable back cover detection...)