On Wed, May 7, 2008 at 4:55 AM, Zhichu Chen [EMAIL PROTECTED] wrote:
Hi everybody,
I'm just writing a module to typeset the traditional Chinese books.
Here is the thing: I use page-arrangement to put like 15 pages on
one page or actually 30 pages on one page in a double-sided mode
(I mean
Aditya Mahajan wrote:
Nice font, BTW.
Don Knuth's punk font.
Hans
-
Hans Hagen | PRAGMA ADE
Ridderstraat 27 | 8061 GH Hasselt | The Netherlands
tel: 038 477 53 69 |
Thanks Wolfgang,
After looking through the file you mentioned above, I finally find that
\writeutilitycommand
and \doutilities are what I want now. Maybe I should look into core-uti.tex
to get more.
On Wed, May 7, 2008 at 2:15 PM, Wolfgang Schuster
[EMAIL PROTECTED] wrote:
On Wed, May 7,
Hello Wolfgang,
Wolfgang Schuster [EMAIL PROTECTED] writes:
take a look into the XML manual, the magazine is a little bit special and
not the best starting point.
http://www.pragma-ade.com/show-man-15.htm
Thank you _very_ much. That was just what I needed: to quote the
example I just ran:
Paul Gideon Dann wrote:
Hi there,
I've got a table of contents for a document that's split into two
large sections. I'm trying to display a centered heading for each
section, and subsections listed in two columns underneath each section
heading. Hopefully this illustrates something
Thanks, that's genius! However, the problem I now have is that the
sections from *both* chapters are displayed below each chapter heading.
That is, \placelist[section] generates the same content in both contexts.
Paul
Hans Hagen wrote:
Paul Gideon Dann wrote:
Hi there,
I've got
On Wed, May 7, 2008 at 1:38 PM, Paul Gideon Dann
[EMAIL PROTECTED] wrote:
Thanks, that's genius! However, the problem I now have is that the sections
from *both* chapters are displayed below each chapter heading. That is,
\placelist[section] generates the same content in both contexts.
The
On Wed, May 7, 2008 at 2:05 PM, Paul Gideon Dann
[EMAIL PROTECTED] wrote:
The same example produces the problem for me. Maybe I have an older
version? I got MacTex pretty recently (two weeks ago), but the version is:
2007.01.12 15:56. Here's the exact source:
Thanks Wolfgang. It's unfortunate that I can't use combinedlist, but I
think I'll be OK without. Thanks again for your time, and I'll get in
touch if I have any more difficulties :)
Paul
Wolfgang Schuster wrote:
On Wed, May 7, 2008 at 2:05 PM, Paul Gideon Dann
[EMAIL PROTECTED] wrote:
(I am still using mkii, which I suspect may matter in this case)
I am able to produce rather nice booklets on US Letter paper, printing
double-sided two-up pages that fold into a booklet and using
texexec --arrange to make it work properly. For documents longer
than about 32 pages, it isn't
Hi Michael,
Arranging pages is not changed from MKII to MKIV. The possibilities are:
% \setuparranging[2*16] %section: one sheet 2 x 16 pages = 32 pages
% \setuparranging[2*8] %section: one sheet 2 x 8 pages = 16 pages
% \setuparranging[2*4] %section: one sheet 2 x 4 pages = 8 pages
%
The same example produces the problem for me. Maybe I have an older
version? I got MacTex pretty recently (two weeks ago), but the version
is: 2007.01.12 15:56. Here's the exact source:
\definecombinedlist[content][chapter]
Peter Rolf wrote:
vardef define_linear_shade (expr a, b, ca, cb) =
hide (_defined_cs_ := _defined_cs_ + 1 ;
_defined_cs_pre_ [_defined_cs_] := ls ;
_defined_cs_post_[_defined_cs_] := 0 1 decimal shadefactor
colordecimals ca ddecimal (a shifted
On Mon, May 05 2008, Wolfgang Schuster wrote:
this is not possible with the TABLE and table environments because of a
switch in core-tsp, table are always splittet to the complete textheight.
\ifinsidecolumns
% brrr, assumes empty columns
\global\setfalse\splitfloatfirstdone
On Mon, May 05 2008, Taco Hoekwater wrote:
Perhaps these bugs can be closed now:
Cetainly, or Perhaps? I have no time to test them myself,
but of course I can close them blindly'
I you consider that MKII and DVI are obsolete and to be replaced by MKIV
and PDF, then certainly!
Cheers,
On Wed, May 07 2008, Oliv wrote:
So, if I understand well there no in-depth French module for ConTeXt. [1]
Isn't it possible to convert the LaTeX packages (Babel French and French
LE) to ConTeXt?
As I'm totally new to ConTeXt, I don't know if it's hardwork or automatic.
Hello Oliv,
If you
16 matches
Mail list logo