a manufacturer should supply guidance on this.
>>>>
>>>> On Thu, Jun 2, 2022, 1:02 PM Dana Orzel via RE-wrenches <
>>>> re-wrenches@lists.re-wrenches.org> wrote:
>>>>
>>>>> Tape is not approved as a wire retainin
via RE-wrenches <
>>> re-wrenches@lists.re-wrenches.org> wrote:
>>>
>>>> Tape is not approved as a wire retaining device as far as I can find in
>>>> the NEC :-]
>>>>
>>>>
>>>>
>>>>
>>&g
.@solarwork.com - C - 208.721.7003
>>>
>>>
>>>
>>> *From:* RE-wrenches *On
>>> Behalf Of *Jerry Shafer via RE-wrenches
>>> *Sent:* Thursday, June 2, 2022 9:40 AM
>>> *To:* RE-wrenches
>>> *Cc:* Jerry Shafer
>>> *Subje
No you certainly cannot rely on that tape for long.
We use stainless wire clips like Heyco SunRunner or RevRunner attached to the
module frame.
https://www.heyco.com/Solar_Power_Components/?sub=wire-management
The QCells AC modules have the microinverters attached so they hang down past
the
:40 AM
> *To:* RE-wrenches
> *Cc:* Jerry Shafer
> *Subject:* Re: [RE-wrenches] wire management on Qcell AC module
>
>
>
> Regarding the tape on the back sheet
>
> I have seen Novis installers keep the tape to secure the modules and I
> have also seen it with th
retaining device as far as I can find in
> the NEC :-]
>
>
>
>
>
> Dana Orzel - E - d...@solarwork.com - C - 208.721.7003
>
>
>
> *From:* RE-wrenches *On
> Behalf Of *Jerry Shafer via RE-wrenches
> *Sent:* Thursday, June 2, 2022 9:40 AM
> *To:* RE-wrenches
&
Subject: Re: [RE-wrenches] wire management on Qcell AC module
Regarding the tape on the back sheet
I have seen Novis installers keep the tape to secure the modules and I have
also seen it with the tape stll attached to the wires laying on the roof so in
my humble opinion the tape is for shipping
G'day All
I rarely do roofs but I can tell you with my pole, ground or DAT projects
it's nearly impossible to cover the modules with a screening product for
safety reasons. I refuse to use the mid panel j-box modules. I'm not one
for boycotts but just use the old school modules with the j-box
These modules are designed for racking w/o MLPE and the rest of the world that
doesn’t use MLPE.
And code in both 300.11 and 330 ish say that wires need to be supported between
6” and 12” ( I’m not sure which is the correct one to use, I’ve always been
told to use 12”) from any box or
I didn't snap a photo yesterday, but next week I will certainly take some
photos, and report back on what we figure out. Definitely sounds like tape
is not a permanent solution.
Cheers,
Dave
On Thu, Jun 2, 2022 at 11:39 AM Jerry Shafer
wrote:
> Regarding the tape on the back sheet
> I have seen
Regarding the tape on the back sheet
I have seen Novis installers keep the tape to secure the modules and I have
also seen it with the tape stll attached to the wires laying on the roof so
in my humble opinion the tape is for shipping only and is not to be used as
a wire management system.
Jerry
enches] wire management on Qcell AC module
That's concerning. We just added these to our product offerings. I reviewed
the QCell installation manual for this product and there doesn't seem to be
any guidance on the subject.
Are the DC leads tight enough when connected to the microin
*Subject:* [RE-wrenches] wire management on Qcell AC module
Hi All,
I just got some of the Qcell 360w AC modules that have the Enphase
microinverter factory applied to the back. The module is the half cut cell
type with the DC leads coming from either side of the middle of the module.
The modules
I just got a quick look at them on the pallet when they arrived on site
yesterday. We will be starting this installation next week, so I can report
back with more details then.
Cheers,
Dave
On Thu, Jun 2, 2022 at 9:47 AM Jason Szumlanski via RE-wrenches <
re-wrenches@lists.re-wrenches.org> wrote:
That's concerning. We just added these to our product offerings. I reviewed
the QCell installation manual for this product and there doesn't seem to be
any guidance on the subject.
Are the DC leads tight enough when connected to the microinverter that they
would not sag enough to touch the roof,
Hi All,
I just got some of the Qcell 360w AC modules that have the Enphase
microinverter factory applied to the back. The module is the half cut cell
type with the DC leads coming from either side of the middle of the module.
The modules come with the wires taped to the back of the module. If you
16 matches
Mail list logo