I have an APRS station on 144.39. I would also like to run my Packet station on
145.03. So I need someway to run both stations. What would I need to do? Can I
build what I would need? If so where would I find that info?
Thanks, Kevin
Kc7hgn
Assuming from reading between the lines that you want to use both stations
on the same antenna, get a 2 meter duplexer. The seperation between the 2
frequencies is 0.64 MHz. At bare minimum you need a notch (reject) duplexer
but a bandpass-band reject type would probably be the better choice.
Good advice.
The only thing that I would add is that you need to use good quality
equipment for the antenna system. This includes the duplexer, jumpers,
connectors, cable and antenna. When you have a situation where two
transmitters can be on the air at the same time on the same antenna
look in your mail box
From: jim law lawsign...@yahoo.com
To: repeater-builder@yahoogroups.com
Sent: Sun, July 18, 2010 10:54:36 AM
Subject: [Repeater-Builder] IC-F420
Does anyone have a service manual for a IC-F420
Thanks Jim
On 7/17/2010 12:47 PM, Bill Smith wrote:
Used is false economy. You end with someone elses problems and high
maintenance
costs as well as downtime which is a bad thing for an ambulance company. The
4010 is a nice reliable system, much simpler than the RoIP stuff but not
nearly
as
On 7/18/2010 10:28 AM, Steve Jones wrote:
Thanks for everyone's input.
Controller choice seems to be like a religion. Everybody has their
favourite and are reluctant to try another brand.
Didn't see anybody mention S-Com!
http://www.scomcontrollers.com/
It'll do what you want, and they
Don't forget that Micor/Mitrek/Syntor/X/Mostar/and just about any other
one from that era will work. I think Maxtrac mics will work
too...maybe...I know a Maxtrac desk mic can be plugged into an older
radio-all you have to do is change the cord...and vice-versa-Maxar desk
mics will work on
S-Com can be a love/hate relationship. The older models did not have
an RS-232 interface, so you needed to keep track of everything
religiously on paper. BUT, they seemed to last forever. I have a few
of them and they have never glitched..never.
The newer S-Com controller has all the
On 7/19/2010 10:02 AM, Joe wrote:
S-Com can be a love/hate relationship. The older models did not have
an RS-232 interface, so you needed to keep track of everything
religiously on paper. BUT, they seemed to last forever. I have a few
of them and they have never glitched..never.
Joe k1ike_m...@... wrote:
S-Com can be a love/hate relationship.
As can be any controller...
The older models did not have an RS-232 interface, so you
needed to keep track of everything religiously on paper.
There is/was Windows Programming Software for all the early
S-Comm
But does it allow you to read what is programmed in the controller?
Joe
On 7/19/2010 1:16 PM, skipp025 wrote:
There is/was Windows Programming Software for all the early
S-Comm Controllers. Yes it used DTMF Control over the and/or
over a phone line. Once you wrote the simple text scripts
Nope. It can only write to the controller.
On 7/19/10 1:23 PM, Joe k1ike_m...@snet.net wrote:
But does it allow you to read what is programmed in the controller?
Joe
On 7/19/2010 1:16 PM, skipp025 wrote:
There is/was Windows Programming Software for all the early
The ability to program over-the-air, via phone line, or through the
optional RS-232 port was one of the big advantages of the ACC
controllers in the 1980's. This was a controller that was way in front
of the curve, but the cost was prohibitive for the average ham.
73, Joe, K1ike
On
Joe k1ike_m...@... wrote:
But does it allow you to read what is programmed
in the controller?
Joe
Sure, I can download an entire image of the controller
programming and save it. Then reprogram those contents
back to the same or a different controller. Handy since
I easily have 10 plus
K5In and I are looking for a couple of UHF Amplifier's that will have 10 to
25 watts in and 70 to 100 watts out. We would prefer n-connectors but will
accept other connectors.
Thanks,
Larry KC7CKO
Hello Group,
I have a Mocom 70 with intact PA section. Radio is a [T73BBA1900BA].
The PA board # is [TLD8882]
The transistor chain is made up of [M9622], [M9624], and (4) four
[M9625].
I thought perhaps that the PA section would make a great 2m amp.
Is anyone interested? I would think the
Don't know if they make an Invar flame suit, but I may need one :)
What I have done in the past is obtained a piece of stainless redi-rod and
short coupling nuts (female on both ends) with the same threading as the
Sinclair.
I then lengthen the rod by only the amount required by cutting the
But that is specific to the 7K controller. I have the 6K and 5K
versions. To my knowledge, they cannot be downloaded.
Joe
On 7/19/2010 2:01 PM, skipp025 wrote:
Joek1ike_m...@... wrote:
But does it allow you to read what is programmed
in the controller?
Joe
Sure, I can download an
Larry,
Last week there was someone trying to sell several Henry UHF amps on the
list. You may want to check your email box.
Mike Mullarkey K7PFJ
6886 Sage Ave
Firestone, Co 80504
303-736-9693
_
From: Repeater-Builder@yahoogroups.com
Stephen Slider stephensli...@... wrote:
Nope. It can only write to the controller.
The original S-Com sold DTMF Software for the 7K.
The Vyex 7K Digital Audio Board allows transfers both
directions.
Although I should mention the image transfer function
was put in (by Dave) to help
Joe k1ike_m...@... wrote:
But that is specific to the 7K controller. I have
the 6K and 5K versions. To my knowledge, they cannot
be downloaded.
Joe
Yeah but that's easily dealt with because you never forget
what you have programmed and it's always right every time
you program it.
At 7/19/2010 09:30, you wrote:
On 7/19/2010 10:02 AM, Joe wrote:
S-Com can be a love/hate relationship. The older models did not have
an RS-232 interface, so you needed to keep track of everything
religiously on paper. BUT, they seemed to last forever. I have a few
of them and they
heh-RS-232 on a ham controller was a pretty rare bird no
matter what...only a few had it...til abt 7-8 years ago
or so...
...so will be be another 7-8 years before we see a USB
interface on all controllers?
Nah we have USB now, just in the form of little adapter boxes
that
It uses a VPN. Not too easy to crack.
From: wd8chl wd8...@gmail.com
To: Repeater-Builder@yahoogroups.com
Sent: Mon, July 19, 2010 8:07:33 AM
Subject: Re: [Repeater-Builder] dispatch consoles
On 7/17/2010 12:47 PM, Bill Smith wrote:
Used is false economy. You
give me an idea of an easy roip console. Any ideas?
-Original Message-
From: Repeater-Builder@yahoogroups.com
[mailto:repeater-buil...@yahoogroups.com] On Behalf Of wd8chl
Sent: Monday, July 19, 2010 9:08 AM
To: Repeater-Builder@yahoogroups.com
Subject: Re: [Repeater-Builder] dispatch
Shure got out of the land mobile microphone market 4(?) years ago.
They now only deal in pro-audio.
WalterH
On 7/19/2010 3:49 PM, n...@no6b.com wrote:
At 7/19/2010 09:30, you wrote:
On 7/19/2010 10:02 AM, Joe wrote:
S-Com can be a love/hate relationship. The older models did not have
an RS-232 interface, so you needed to keep track of everything
religiously on paper. BUT, they seemed to last
Does anyone have any information on the Andrew DB436-2 Phasing Transformer
used as a phasing harness to connect two Andrew DB-436A antennas together?
I need to build one for a remote RX site. I have the information on the
DB-5009 dual yagi mounting bracket.
Thanks,
--
James Adkins, KB0NHX
28 matches
Mail list logo